Forum: Model-A
06-27-2022, 01:36 PM
|
Replies: 1
Views: 700
|
Forum: Model-A
06-16-2022, 03:02 PM
|
Replies: 1
Views: 700
Zenith 3 Side Bowl Carburator
This is a rare Zenith 3 side bowl carburator completely rebuilt to show standards and road tested. Correct plating and gas resistant paint. $750.00 includes shipping. E mail: [email protected] or call:...
|
Forum: Model-A
06-16-2022, 02:45 PM
|
Replies: 0
Views: 567
Zenith 2 Side Bowl Carburator
Zenith 2 side bowl carburetor completely rebuilt to show standards and road tested. Correct plating and gas resistant paint. $350.00 plus shipping and insurance. Email to: [email protected] or call at...
|
Forum: Model A (1928-31)
02-23-2022, 11:53 AM
|
Replies: 55
Views: 7,256
|
Forum: Model-A
09-08-2021, 11:39 AM
|
Replies: 0
Views: 735
Zenith & Holley Carb Parts Wanted
In search of original throttle arms for Zenith and Holley Model A carburetors. The correct shafts are made of brass. Must not be worn out or rust pitted arms. Please contact me if you are in need of...
|
Forum: Model A (1928-31)
08-05-2018, 11:12 AM
|
Replies: 19
Views: 4,056
|
Forum: Model-A
04-27-2018, 09:15 PM
|
Replies: 0
Views: 946
Early Zenith carb bottom
Looking for early recessed Zenith, (No 1), double venturi carb bottom, domed dowl pin boss on engine side, no dowel pin boss on hood side. Bowl rim design small boss. [email protected]
|
Forum: Model A (1928-31)
10-26-2017, 11:32 AM
|
Replies: 13
Views: 2,847
Re: ZENITH 2 sidebowl carb question
I just rebuilt a carb that had a brass or bronze filter on it, it was no good at all as someone drilled out the gas inlet and no way to hook up the gas line. Also the drain valve was not the right...
|
Forum: Model A (1928-31)
09-14-2017, 12:00 PM
|
Replies: 0
Views: 744
Raised Zenith @ carbs & third brass plug
Some pictures of Raised Zenith 2 carbs and others. I have 15 Raised Zenith 2 carbs None without the 2 as discused a few days ago. I will sell them if you need one
|
Forum: Model A (1928-31)
02-28-2017, 10:35 AM
|
Replies: 13
Views: 2,781
Re: Carb Question
As Richard L. said if the solder flows deeper into the jet which it usally does, it is very necessary to flow test the jets to see how they flow.
|
Forum: Model A (1928-31)
02-25-2017, 11:31 AM
|
Replies: 35
Views: 6,143
Re: Broken Zenith 2 carb
Hello Rusty
It can be fixed by brazing it. like others said it has to be put in a jig that holds it in place. I have done several but they were not broken into the throat like yours. May be better...
|
Forum: Model A (1928-31)
02-09-2017, 12:17 PM
|
Replies: 15
Views: 2,457
|
Forum: Model A (1928-31)
10-08-2016, 06:50 PM
|
Replies: 17
Views: 3,213
Re: Leaky Carb
More than likely the float valve, not a good one made today. Some work most do not.
|
Forum: Model A (1928-31)
10-08-2016, 06:42 PM
|
Replies: 11
Views: 4,303
|
Forum: Model A (1928-31)
09-10-2016, 12:54 PM
|
Replies: 16
Views: 2,842
|
Forum: Model A (1928-31)
09-10-2016, 12:45 PM
|
Replies: 34
Views: 7,740
Re: Where are the GAV Wrench's
I made my own several years ago, just took a 3/8" deep socket and carefully filed it down to 13/32", works just fine and I use a lot to rebuild carburetors.
|
Forum: Model A (1928-31)
07-21-2016, 03:54 PM
|
Replies: 40
Views: 8,566
|
Forum: Model A (1928-31)
07-14-2016, 03:08 PM
|
Replies: 29
Views: 7,261
|
Forum: Model A (1928-31)
07-03-2016, 08:57 PM
|
Replies: 10
Views: 2,525
Re: clutch release shaft arm broke
Same thing happened to me, out with the car and could not shift, made it home in second gear. Did not know this is a frequent problem. Asked on this forumn and did not hear about this happening....
|
Forum: Model A (1928-31)
06-09-2016, 10:51 AM
|
Replies: 74
Views: 21,594
|
Forum: Model A (1928-31)
05-15-2016, 04:42 PM
|
Replies: 4
Views: 1,710
|
Forum: Model A (1928-31)
04-15-2016, 07:59 PM
|
Replies: 7
Views: 2,159
Re: rear drum bearing
Looks like an original to me. Just looked at mine ,were purchased years ago, still look OK.
|
Forum: Model A (1928-31)
04-15-2016, 07:55 PM
|
Replies: 24
Views: 13,232
|
Forum: Model A (1928-31)
04-05-2016, 01:52 PM
|
Replies: 11
Views: 2,696
Re: Clutch release shaft arm
2 replies
Yes the vendors sell a replacement arm. I had an old housing out in the shed that I was able to get the arm off of and used that. I will have to keep an eye on it.
I have not been...
|
Forum: Model A (1928-31)
04-05-2016, 07:00 AM
|
Replies: 11
Views: 2,696
Re: Clutch release shaft arm
Hello Ray
I also went back and looked at the original discussion and could not find any thing about a broken arm. It is good that is all up graded now. Thanks to everbody
|