Forum: Model-T
01-01-2013, 06:21 PM
|
|
Replies: 0
Views: 1,621
wtt 1916 Maxwell touring body
I have a 1916 Maxwell touring body I would like to trade for a '23-25 or '26-27 roadster or RPU body. This touring is in amazing shape, the wood is super solid and original. Sheetmetal is the best...
|
|
Forum: Early V8
07-14-2012, 09:59 AM
|
|
Replies: 0
Views: 519
1940 v8-60 rod bearings complete set
These are a NOS Ford set of .020 rod bearings. part # 92A-6211. There for a .020 crank and STD. rods. This set does all 8 rods. $70 includes shipping in the U.S. Thanks!
|
|
Forum: Early V8
07-01-2012, 03:32 PM
|
|
Replies: 2
Views: 1,483
8ba flathead good running engine
Im selling a 8ba for a friend, it came out of his '50 coupe for a late drivetrain swap. This motor ran great, didnt smoke or make any noise. It's complete except for the carb. It may be a '52 or '53...
|
|
Forum: Model-A
06-23-2012, 02:40 PM
|
|
Replies: 7
Views: 4,278
|
|
Forum: Early V8
12-21-2011, 02:47 PM
|
|
Replies: 0
Views: 1,652
1935 Harley flathead engine
I've got a rebuilt, ready to run 1935 Harley VLD 74" flathead engine. It's totally rebuilt, .020 pistons, all new shafts, bearings, cages and races. Correct VLD high compression heads, M51 UL carb,...
|
|
Forum: Model T (1909-1927)
06-19-2011, 02:44 PM
|
|
Replies: 5
Views: 1,908
Re: Spring Perch Boss Thickness
You will have to mill down the T axle 1/8" on the top and bottom to reduce it the 1/4" diffrence. Also the angle on the A wishbone ends is wrong, you need to cut them loose at the trans mount casting...
|
|
Forum: Model-T
06-06-2011, 10:20 AM
|
|
Replies: 3
Views: 1,532
|
|
Forum: Model-T
05-22-2011, 01:25 PM
|
|
Replies: 3
Views: 1,532
'26-'27 roadster rear quarters, inner brace
turtle deck quarters and the lower inner brace. The deck sides are in good shape, very little rust through at the bottoms, and the brace is straight, just needs cleaned up and painted. Dont want to...
|
|
Forum: Model-T
05-22-2011, 01:18 PM
|
|
Replies: 0
Views: 1,160
'24-'25 fenders, aprons, trunk lid for coupe
I am selling some parts for a 1925 coupe. All the fenders, spare tire rack, side aprons, trunk lid and a wheel that was on the spare rack. The fenders have some old weld repairs, and one of the rears...
|
|
Forum: Model-A
04-24-2011, 03:28 PM
|
|
Replies: 3
Views: 1,608
|
|
Forum: Model-A
04-23-2011, 01:42 PM
|
|
Replies: 3
Views: 1,608
|
|
Forum: Model-A
04-22-2011, 09:50 AM
|
|
Replies: 3
Views: 1,608
Model A Modified/speedster
Selling my modified roadster, this is a new build. Body is based on a 28-29 cowl, the rest is hand built. Driveline is from a '31 roadster and runs great. The frame is custom built 2x3 with a model A...
|
|
Forum: Model-A
02-25-2011, 02:57 PM
|
|
Replies: 2
Views: 1,293
|
|
Forum: Model-A
02-25-2011, 02:56 PM
|
|
Replies: 3
Views: 1,606
|
|
Forum: Model-T
02-25-2011, 02:56 PM
|
|
Replies: 1
Views: 1,459
|
|
Forum: Model-T
02-25-2011, 02:56 PM
|
|
Replies: 1
Views: 1,332
|
|
Forum: Model-T
02-25-2011, 02:55 PM
|
|
Replies: 2
Views: 1,859
|
|
Forum: Model-A
02-25-2011, 11:50 AM
|
|
Replies: 2
Views: 1,293
Tropic Aire water neck
This is a Tropic Aire water neck for a A. it has the heater valve in it but the valve will need to be repaired, or replaced. Very solid no bad corrosion inside, good neck. if your running a heater in...
|
|
Forum: Model-A
02-25-2011, 11:45 AM
|
|
Replies: 3
Views: 1,606
Winfield cast Iron head
I have a cast Iron Winfield head for sale. It has a K7 stamped in it which I believe makes it a 7.1 compression head. It's been magnafluxed and has no cracks. it needs to be surfaced and the chambers...
|
|
Forum: Model-T
02-25-2011, 11:39 AM
|
|
Replies: 1
Views: 1,332
|
|
Forum: Model-T
02-25-2011, 11:35 AM
|
|
Replies: 1
Views: 1,459
frontenac oil pan sump
This is a never used Frontenac deep sump finned aluminum oil pan for a T. The bolt holes were never drilled, it needs to be bead blasted, its just been in storage forever. $75 plus $15 shipping....
|
|
Forum: Model-T
02-25-2011, 11:31 AM
|
|
Replies: 2
Views: 1,859
iandola finned aluminum head
This is a Iandola high compression head for a T. It is a unfinished blank. The chambers and water jackets dont need anything, but the head bolt holes need to be drilled and the spark plug holes need...
|
|
Forum: Model-A
02-12-2011, 12:56 PM
|
|
Replies: 1
Views: 850
WTB engine in florida
Looking for a good A motor, something that ran recently or is known as good. Doesnt need to have manifolds, Thanks in advance, Rob.
|
|
Forum: Model A (1928-31)
01-23-2011, 08:05 PM
|
|
Replies: 79
Views: 18,838
Re: Model A myths
I like it when people tell me they like the ones that didnt come with fenders.
|
|
Forum: Model T (1909-1927)
01-12-2011, 01:03 PM
|
|
Replies: 8
Views: 2,756
|
