Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: cas3
Forum: Early V8 (1932-53) Yesterday, 11:38 PM
Replies: 8
Views: 255
Posted By cas3
Re: chrome stripping?

google it up. there are youtube videos of guys doing it. not electrolysis like rust removal with a battery charger, they are using a welder for power
Forum: Early V8 (1932-53) 04-01-2020, 09:43 PM
Replies: 17
Views: 808
Posted By cas3
Re: Guility as charged ??!!

looks to be about 25ish with the demountable wheels. too bad you aren't closer i would have given you similar for a couple distributors. have fun with it bubba, stay healthy!
Forum: Early V8 (1932-53) 04-01-2020, 12:20 AM
Replies: 23
Views: 839
Posted By cas3
Re: Been dabbling in Stainless trim repair

back in my tri5 chevy days i bought side trim from a guy that thats all he did was fix 5-6-7 stainless trim. had a 2 car garage full of it, and made a nice living with very little $ in tools
Forum: Early V8 (1932-53) 03-31-2020, 04:41 PM
Replies: 20
Views: 558
Posted By cas3
Re: Who lightens flywheels? Looking for a shop

i've done them too. in my 14" clausing they only fit with the ring gear off. i've taken the big blob off of several of the early 9" clutch's. use a bit for cast iron and run slow. it takes several...
Forum: Early V8 (1932-53) 03-31-2020, 03:55 PM
Replies: 0
Views: 98
Posted By cas3
34 window channels

i'll try a new approach. trying to install vintique window channel kits. i said they look ok, well before i tried to install them. in the blue instruction sheet they say short channel rear, long...
Forum: Early V8 (1932-53) 03-30-2020, 05:50 PM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

thats what i thought too, however the clip at the bottom of each channel is not big enough to fit it in. i was going to scalp a little out with the wiz wheel, but playing with the fuzzy channels it...
Forum: Early V8 (1932-53) 03-30-2020, 05:18 PM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

got my springs today, not in yet but i can see how they go, thanks. been fighting with window channels today, can any one tell me where this rubber bumper attaches ? C&G part # B7021580, 32-34 lower...
Forum: Early V8 (1932-53) 03-29-2020, 10:00 PM
Replies: 76
Views: 4,353
Posted By cas3
Re: What in Tarnation?

no virus in my shop either. when they close the hardware store i'll be pissed
Forum: Early V8 (1932-53) 03-29-2020, 09:57 PM
Replies: 16
Views: 637
Posted By cas3
Re: Cutting down 42 to 48 ford axles for a 40 ford

i was gonna do it once, but quit the idea. never could get the exact degree, i think its 7, and also i never get a nice cut when turning the compound by hand. had a cnc guy but he wanted a blue...
Forum: Early V8 (1932-53) 03-27-2020, 10:40 AM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

two of the tabs on this cover have already been broken and welded by a previous owner. i'll figger something out when i get the spring
Forum: Early V8 (1932-53) 03-26-2020, 09:48 PM
Replies: 4
Views: 196
Posted By cas3
Re: 1950 Transmission Input Shaft

a little side to side play is pretty normal, in and out should be none, or darn close to it
Forum: Early V8 (1932-53) 03-26-2020, 09:45 PM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

so, your original spring looks like the ones Terry shows, and the replacements i ordered look like the the catalog picture the deuce lover shows. should be interesting trying to reshape the spring!...
Forum: Early V8 (1932-53) 03-26-2020, 02:59 PM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

yep, like usual i just received a parts order, and now i need to order a spring!! thanks all
Forum: Early V8 (1932-53) 03-26-2020, 11:16 AM
Replies: 20
Views: 535
Posted By cas3
Re: 1933 door latch help

i am playing with doors at this time also, Terry could you please tell more about the second spring for the lock? i dont have one, and dont see what it it would hook up to. thanks. i have early...
Forum: Early V8 (1932-53) 03-24-2020, 04:16 PM
Replies: 7
Views: 271
Posted By cas3
Re: 34 3W door window/risor questions

thank you all. i looked at my other channel, its marked L , but is clearly the right side. even the label on the boxes were backwards, but at least they did not send two of one side! i bought some...
Forum: Early V8 (1932-53) 03-24-2020, 10:54 AM
Replies: 8
Views: 378
Posted By cas3
Re: A bit of machining. Re-drilling a flywheel.

another good show mart! i have had one of those clicker/counter things laying around for years, now i know of a use for it
Forum: Early V8 (1932-53) 03-23-2020, 10:10 PM
Replies: 9
Views: 793
Posted By cas3
Re: What happens in a transmission rebuild - Part 2

i have access to a shot blast cabinet like that, it shoots cast iron balls. i have used it on cases, but you run the gears and shafts thru there too?
Forum: Early V8 (1932-53) 03-23-2020, 09:42 PM
Replies: 7
Views: 271
Posted By cas3
Re: 34 3W door window/risor questions

David, no i am not ready for installation, just trying to lay it all out and study to avoid my usual circumstance of try to put it together and realize i am missing some part, then waist shipping and...
Forum: Early V8 (1932-53) 03-23-2020, 04:02 PM
Replies: 7
Views: 271
Posted By cas3
34 3W door window/risor questions

i'm getting ready to finish up my doors and get some glass in them. i bought all the stuff from c&g, mostly vintique, whatever, looks fine to me. looking at the bottom channel that the glass sits in,...
Forum: Early V8 (1932-53) 03-23-2020, 03:48 PM
Replies: 60
Views: 3,870
Posted By cas3
Re: petehoovie???

i dont know anything about the server change, but to answer Kubes question, Pete was a frequent contributor, 34 sedan owner, avatar with the pretty Bud girls sitting on his old ford, and a master...
Forum: Early V8 (1932-53) 03-21-2020, 06:57 PM
Replies: 25
Views: 1,151
Posted By cas3
Re: My wife hates crankshafts...

years ago i returned home from an auction with a bunch stuff, and some bare model T blocks got unloaded in the driveway to be moved later. i brought a new girlfriend home that night, i even warned...
Forum: Early V8 (1932-53) 03-21-2020, 06:49 PM
Replies: 4
Views: 367
Posted By cas3
Re: robert stewart thermastats

goodness! this is getting confusing!
Forum: Early V8 (1932-53) 03-21-2020, 06:17 PM
Replies: 5
Views: 305
Posted By cas3
Re: Time to work

no time for the A right now, busy working on a v8
Forum: Early V8 (1932-53) 03-20-2020, 09:07 PM
Replies: 60
Views: 3,870
Posted By cas3
Re: petehoovie???

yup, sure do miss those "bud' girls
Forum: Early V8 (1932-53) 03-19-2020, 11:56 PM
Replies: 13
Views: 467
Posted By cas3
Re: New horn issue

nelsb01 is correct, but to just fix the spring under the button you may be able to just lift the rod up enough to work on the tabs that hold the button down, instead of completely removing the...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:43 PM.