Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 104
Search took 0.01 seconds.
Search: Posts Made By: steamgas
Forum: Model-A 08-18-2020, 04:43 PM
Replies: 0
Views: 410
Posted By steamgas
Wanted:1929-1932 model a shock

i am looking for a good rebuild-able shock absorb-er for a 1929 model a ford truck. it must be the ac for the right rear. send me a picture of what you have.


steamgas0@gmail.com...
Forum: Early V8 (1932-53) 02-15-2018, 02:08 PM
Replies: 9
Views: 1,346
Posted By steamgas
Re: 6 volt vs 12 volt

fordwife said from 6 volt positive.is this true?were all fords up too 1956 positive ground?
Forum: Early V8 (1932-53) 02-11-2018, 09:56 AM
Replies: 32
Views: 4,099
Posted By steamgas
Re: Spark timing question

dear Mr hoop this is the exact question i am asking
Forum: Early V8 (1932-53) 02-10-2018, 01:24 PM
Replies: 32
Views: 4,099
Posted By steamgas
Spark timing question

i know this question has been asked before but i need to know where to go to get the information i need. my rebuilt engine runs good but i need to now set the spark timing. i know it has an...
Forum: Late V8 (1954+) 02-10-2018, 01:22 PM
Replies: 1
Views: 727
Posted By steamgas
Spark timing question

i know this question has been asked before but i need to know where to go to get the information i need. my rebuilt engine runs good but i need to now set the spark timing. i know it has an...
Forum: Early V8 (1932-53) 01-30-2018, 12:58 PM
Replies: 1
Views: 418
Posted By steamgas
Add on oil filter cartage

can some one tell me the maker and part number for the filter for my add on oil filter? as best i can tell it is 4 1/2" outside diameter and 4 1/2" long.
Forum: Early V8 (1932-53) 01-26-2018, 02:44 PM
Replies: 6
Views: 836
Posted By steamgas
Re: Fuel pump push rod

sorry guy's i feel like the man in Hawaii who pushed the wrong button and caused a false alarm for a nuclear attack.when i reamed out the bushing for the push rod i never went all the way thru....
Forum: Early V8 (1932-53) 01-26-2018, 02:09 PM
Replies: 6
Views: 836
Posted By steamgas
Fuel pump push rod

i just inserted the fuel pump rod down onto the cam lobe but there is no lift on the rod. what am i doing wrong?
Forum: Early V8 (1932-53) 01-19-2018, 08:34 AM
Replies: 4
Views: 653
Posted By steamgas
Re: Need information on an engine part

thanks guy's this helps a lot. i was going to make my own oiling system for the valves but you all say that the splash system is all it takes to get the right amount of oil up there. when i first saw...
Forum: Early V8 (1932-53) 01-19-2018, 08:14 AM
Replies: 4
Views: 653
Posted By steamgas
Need information on an engine part

can someone describe the function of the oil baffle (part # 6524)? there are 2 of theses parts in the engine just under the carb manifold that are attached by spring force to the oil galley tube.
Forum: Early V8 (1932-53) 01-17-2018, 07:40 AM
Replies: 10
Views: 1,073
Posted By steamgas
Re: ford flathead v8 crankshaft pully

thanks guy's for the information
Forum: Early V8 (1932-53) 01-17-2018, 07:37 AM
Replies: 4
Views: 410
Posted By steamgas
Re: v8 motor valve assembly oiling

dear sir
thank you for the reply back. i believe you are right.
Forum: Early V8 (1932-53) 01-17-2018, 07:14 AM
Replies: 4
Views: 410
Posted By steamgas
v8 motor valve assembly oiling

i have a question about the oiling process of the lifters and valve assemblies. how dose any oil get to the upper part of the motor? what am i missing? i see no oil ports at all oiling this part of...
Forum: Early V8 (1932-53) 01-17-2018, 07:03 AM
Replies: 10
Views: 1,073
Posted By steamgas
Re: ford flathead v8 crankshaft pully

thank you sir for the reply back.i am having trouble getting the fan belt to go over the pullies. i ordered the belt from mac's and it is 55 inches long but still will not work. any suggestions?
Forum: Early V8 (1932-53) 01-15-2018, 04:38 PM
Replies: 10
Views: 1,073
Posted By steamgas
Re: ford flathead v8 crankshaft pully

this is a 1935 ford flathead
Forum: Early V8 (1932-53) 01-15-2018, 01:52 PM
Replies: 10
Views: 1,073
Posted By steamgas
ford flathead v8 crankshaft pully

what is the diameter of the front crankshaft pulley?
Forum: Early V8 01-01-2018, 01:51 PM
Replies: 0
Views: 415
Posted By steamgas
Wanted:information on eaely v8 distributor

i am looking for detailed information on how to set up a 1932-1935 distributor.i just can't find what i am looking for.can some one here point me in the right direction?:confused:
Forum: Late V8 12-23-2017, 10:51 AM
Replies: 0
Views: 641
Posted By steamgas
wanted oil pan

looking for a good oil pan for a 1935 ford v8. let me know what you have.
Forum: Early V8 (1932-53) 07-13-2017, 07:40 AM
Replies: 4
Views: 663
Posted By steamgas
Looking for a good supplier of rod bearings

i have just had a 1935 ford crankshaft reground too -.020 on the rod bearings diameters.i now need to find the bearing for this size.i need help!!!!!:eek:
Forum: Early V8 (1932-53) 05-27-2017, 08:35 AM
Replies: 2
Views: 553
Posted By steamgas
camshaft grinder supplier on east coast

i need someone to grind my camshaft who is located on the east coast.can someone recommend a company.in VA. ?
Forum: Early V8 (1932-53) 05-01-2017, 08:44 AM
Replies: 10
Views: 1,207
Posted By steamgas
Re: v8 babbitt motores

thanks guys for the reply.it only stands to reason that shims were used.why scrap a perfectly good motor for only .002 wear on the Babbitt when all you have to do is remove a .001 shim and have a...
Forum: Early V8 (1932-53) 04-27-2017, 10:14 AM
Replies: 10
Views: 1,207
Posted By steamgas
v8 babbitt motores

do the early v8 Babbitt motors have shims under the bearing cap like the model a engines have to take up the wear of the Babbitt material
Forum: Early V8 (1932-53) 04-25-2017, 01:32 PM
Replies: 4
Views: 534
Posted By steamgas
Smile machining 1934 motor block for main's

i need to know what the engineering diameter and tolerance is for the main's on a 1934 block.is there someone here that i can talk too about this?
Forum: Early V8 (1932-53) 03-08-2017, 09:36 AM
Replies: 8
Views: 1,238
Posted By steamgas
line boreing for insert main bearings

what is the diameter the block needs too be line bored out to too except insert main bearings?please give machinist numbers and tolerances.this is an early Babbitt block that i want to update to...
Forum: Early V8 (1932-53) 02-12-2017, 01:08 PM
Replies: 1
Views: 632
Posted By steamgas
v-8 crankshaft blueprints

several years back i was able too get crankshaft blueprints for the model a crankshaft from the Henry ford museum.my question is can i get the blueprints for the v-8 crankshaft from the years...
Showing results 1 to 25 of 104

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:45 PM.