Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts Made By: 32pu
Forum: Early V8 (1932-53) 02-10-2020, 05:00 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Ok thanks for that tip that makes sense, and easy to
execute
Forum: Early V8 (1932-53) 02-10-2020, 12:48 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Steve/IL, that's a possibility to check into, I'll look under the dash tonight. But at a glanceit appeared that everything was factory install. The cowl vent (green paint) matches what's on the...
Forum: Early V8 (1932-53) 02-09-2020, 10:58 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Hello David, yes that extra hole is what was used to bolted shut by the prior owner. The lower level ratchet is the one that was in the truck, I tried the new one didn’t seem to make a difference if...
Forum: Early V8 (1932-53) 02-09-2020, 06:03 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

So first two photos show Calvin laying fairly flush in place, but the vent is not centered within the opening thereís a large gap on the back. Second two photos show itís centered where I think it...
Forum: Early V8 (1932-53) 02-09-2020, 05:53 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Hereís the mechanism
Forum: Early V8 (1932-53) 02-09-2020, 05:42 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Hereís some more photos of the vent
Forum: Early V8 (1932-53) 02-09-2020, 05:29 PM
Replies: 20
Views: 610
Posted By 32pu
Re: 32 Ford Cowl Vent

Thanks for the replies, David this truck is mostly original. The fit shown in the pictures is without the gasket and the cowl vent disconnected from the mechanism. It doesn’t appear that the cowl...
Forum: Early V8 (1932-53) 02-09-2020, 01:30 AM
Replies: 20
Views: 610
Posted By 32pu
32 Ford Cowl Vent

Hello, when I got my pickup, someone had previously drilled a hole in the cowl vent and bolted it closed using fender washers.

bought a new gasket and spring

Seems that with or without gasket...
Forum: Early V8 (1932-53) 12-28-2019, 12:46 AM
Replies: 4
Views: 302
Posted By 32pu
32 Ford Pickup windshield frame removal

So the windshield is open and I removed all the screws from the under side of the cab header (top of windshield).

And the 3 nuts on the topside off the cab header.

Swing arms are disconnected....
Forum: Early V8 (1932-53) 12-14-2019, 05:54 PM
Replies: 14
Views: 929
Posted By 32pu
Re: Steering box/shaft removal procedure.

Thanks this was very helpful!!
Forum: Early V8 (1932-53) 10-18-2019, 12:17 AM
Replies: 7
Views: 727
Posted By 32pu
Re: Rear view mirror

Did the 32 pickup have an interior rear view mirror?
Forum: Model A (1928-31) 07-03-2017, 11:55 PM
Replies: 16
Views: 1,798
Posted By 32pu
Re: rear end change

Hello guys, working on my 32 Pickup, removed rear end, replaced the shackle bushings, now ready to install rear end. I put shackles plates on passenger side rolled over to the drive side, and have a...
Forum: Early V8 (1932-53) 03-22-2015, 12:13 AM
Replies: 176
Views: 59,297
Posted By 32pu
Re: The Official '32-'34 Truck Thread

Question I have a 32 pickup pretty original daily driver, I would like to add a rear bumper.

Any suggestions for rear bumper mounting brackets?
Forum: Questions & Suggestions 06-25-2013, 11:59 PM
Replies: 0
Views: 568
Posted By 32pu
1932 pickup rear bumper brackets

Hi, I've seen trucks with rear bumpers. Does everyone fabricate, or can you use brackets from another vehicle?
Showing results 1 to 14 of 14

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:40 PM.