Forum: Early V8 (1932-53)
08-23-2022, 09:11 AM
|
Replies: 28
Views: 2,165
Re: What would cause my right front to be lower?
I’ll get under it in the next day or so and see if I see anything that doesn’t look right. I had the steering box rebuilt a while back and had the alignment checked. Everything was good. Alignment...
|
Forum: Early V8 (1932-53)
08-22-2022, 04:37 PM
|
Replies: 28
Views: 2,165
Re: What would cause my right front to be lower?
Yeah that parking lot picture is not the best although the lot is level..my truck has been like this since I have owned it. The tires are all the same size. I measured from the bottom of the shocks...
|
Forum: Early V8 (1932-53)
08-22-2022, 02:46 PM
|
Replies: 28
Views: 2,165
What would cause my right front to be lower?
Hello all,
What would cause my right front area on my truck to be lower? I can have it on level ground and put a four foot level across the bumper supports and the right side is about an inch lower....
|
Forum: Early V8 (1932-53)
08-17-2022, 05:08 AM
|
Replies: 59
Views: 9,524
Re: Title Woe’s
VA should have a DMV officer that handles stolen vehicles and applications for new titles, collision repair and so on. That’s who you should try and make friends with…good luck
|
Forum: Early V8 (1932-53)
07-20-2022, 10:35 AM
|
Replies: 4
Views: 778
|
Forum: Early V8 (1932-53)
07-19-2022, 10:56 AM
|
Replies: 4
Views: 759
|
Forum: Early V8 (1932-53)
07-18-2022, 01:28 PM
|
Replies: 4
Views: 759
|
Forum: Early V8 (1932-53)
07-13-2022, 04:47 PM
|
Replies: 5
Views: 746
Rear brake drum puller for my’41 pu
Hello all,
I’m looking for recommendations/ options for a rear brake drum puller. I’ve did some searching and really didn’t come up with anything. Thanks in advance…Randy
|
Forum: Early V8 (1932-53)
11-17-2021, 05:43 PM
|
Replies: 1
Views: 657
|
Forum: Early V8 (1932-53)
11-17-2021, 01:29 PM
|
Replies: 1
Views: 657
|
Forum: Early V8 (1932-53)
06-02-2020, 10:17 AM
|
Replies: 0
Views: 566
Speedo issue continues
Hello all,
Over the past year or so I‘ve been working on my speedometer. When I first started driving the truck it didn’t work at all. I removed the dash cluster, cleaned and oil and got it...
|
Forum: Early V8 (1932-53)
05-19-2020, 04:11 PM
|
Replies: 1
Views: 790
Need help with a throttle rod
Hello all,
Hope everyone is doing good. I need some help with the location, type of linkage and pieces needed for throttle rod set up on my 41 truck. All I have is the knob inside of the truck. Not...
|
Forum: Early V8 (1932-53)
05-17-2020, 05:40 PM
|
Replies: 32
Views: 5,222
Re: Engine diaper
I have used a cookie sheet over the years on different vehicles. Just deep enough for an absorbent pad. Drill holes and zip tie where needed.
|
Forum: Early V8 (1932-53)
04-23-2020, 02:19 PM
|
Replies: 8
Views: 1,637
Re: Holley model 94 Carburetor Questions
Charlie is the best. Sent him my “good” running carb a couple of months ago. Very quick turnaround time due to me going out of town. I got it installed and it fired right up to a smooth idle. Starts...
|
Forum: Early V8 (1932-53)
01-03-2020, 06:51 PM
|
Replies: 7
Views: 1,255
Re: speedometer cleaning/repair on my '41 PU
I believe I may have serviced it. Was able to get it apart, cleaned and got the odometer working. It's rainy here today and tomorrow so I'll test drive it Sunday. Thanks for all of the suggestions.
|
Forum: Early V8 (1932-53)
01-03-2020, 08:42 AM
|
Replies: 7
Views: 1,255
Re: speedometer cleaning/repair on my '41 PU
The cable and everything works fine. I'd like to know how to remove the needle without damaging anything. I thought I had run across a post a while back that explained the procedure. Can't seem to...
|
Forum: Early V8 (1932-53)
01-02-2020, 08:59 PM
|
Replies: 7
Views: 1,255
speedometer cleaning/repair on my '41 PU
Hello all,
I've tried search and couldn't find anything about speedometer cleaning/repair. I know it's there because a few months ago I was able to get my non working speedo to at least work a...
|
Forum: Early V8 (1932-53)
12-25-2019, 07:31 PM
|
Replies: 35
Views: 5,358
Re: Junior Johnson Passes On
Junior was right popular in the Wilkesboro NC area. Up until the last few years the local news would do a story about him every once in a while. Was truly one of the first Nascar pioneers.
|
Forum: Early V8 (1932-53)
12-22-2019, 06:19 PM
|
Replies: 15
Views: 2,040
Re: Options for mounting a spare tire on my '41PU
Thanks for the replies. Alan I didn't see that in your post. I'll PM you. I'll also look into the bracket that Floyd mentioned. I also need to pick up a wheel and tire. I'm running 15" Mercury...
|
Forum: Early V8 (1932-53)
12-22-2019, 04:09 PM
|
Replies: 15
Views: 2,040
Re: Options for mounting a spare tire on my '41PU
I wish I had checked into all of this before I painted my new bed and could have mounted the "bed only" mount. Looks like I need what Bill has in the above photo. I've checked ebay off and on and...
|
Forum: Early V8 (1932-53)
12-21-2019, 08:38 PM
|
Replies: 15
Views: 2,040
Options for mounting a spare tire on my '41PU
Hello all,
I'd like some suggestions or options for mounting the spare tire on my PU. The only thing I currently have is a hole in the running board and the divet in the fender.
TIA,
Randy
|
Forum: Early V8 (1932-53)
10-14-2019, 09:32 AM
|
Replies: 13
Views: 2,260
|
Forum: Early V8 (1932-53)
10-14-2019, 09:26 AM
|
Replies: 13
Views: 2,260
|
Forum: Early V8 (1932-53)
10-12-2019, 04:08 PM
|
Replies: 13
Views: 2,260
|