Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 269
Search took 0.02 seconds.
Search: Posts Made By: 95476
Forum: Early V8 (1932-53) 08-04-2020, 07:56 PM
Replies: 7
Views: 453
Posted By 95476
Re: '33 Sedan Delivery, what goes here ?

My car has the same drip rail. At each end there is a hole about 1/2 inch from the end. I had a '36 sedan delivery and it never had them.
I am thinking they are screw holes to secure the ends of...
Forum: Early V8 (1932-53) 08-03-2020, 06:57 PM
Replies: 7
Views: 453
Posted By 95476
'33 Sedan Delivery, what goes here ?

I am doing the heavy metal work on the body and want to find out what the holes at the ends of the rear drip rail are for.
Were there screws in those holes ?
Retainers for rubber ?
Any info is...
Forum: Early V8 07-25-2020, 10:44 PM
Replies: 0
Views: 144
Posted By 95476
'33/'34 Sedan Delivery Seats

I was fortunate to finally locate a '33 sedan delivery. Now I am looking for the proper front seats for the car. I have a very nice set of '33 2-Dr sedan front seats that would work Ok but now that...
Forum: Early V8 (1932-53) 07-05-2020, 11:20 AM
Replies: 18
Views: 822
Posted By 95476
Re: supplier of 1933-34 Ford Windshield Rubber

I have used Carpenter and Drake. The last two I did came with the frame from Trautwein.
The hardest parts is removing all the old rubber from the frame.
Forum: Early V8 (1932-53) 07-05-2020, 11:17 AM
Replies: 14
Views: 555
Posted By 95476
Re: 34 radiator

X3 Brassworks as well.
Forum: Early V8 (1932-53) 06-30-2020, 09:37 PM
Replies: 15
Views: 970
Posted By 95476
Re: Plugging holes with "Metal To Metal?"

If you have it apart, spend the time and repair it correctly if you can. Better to do it now than regret not doing it later on. There is enough stuff that happens that is unexpected, putting it back...
Forum: Early V8 06-20-2020, 06:53 PM
Replies: 0
Views: 92
Posted By 95476
'36 Ford Header Tack Strip

I have a nice left over headliner tack strip for a '36 Ford.
I had a hard time finding one when I needed it so I bought two.
I never used this one.
$45.00 plus shipping.
Thank You
Forum: Early V8 06-20-2020, 06:37 PM
Replies: 0
Views: 101
Posted By 95476
Columbia 2-speed vacuum can

I am selling an extra Columbia 2- speed vacuum canister. I had my rear end completely gone through and replaced it with a new can.
This one has some small pits that can be filled with JB weld. This...
Forum: Early V8 (1932-53) 06-17-2020, 03:07 PM
Replies: 12
Views: 557
Posted By 95476
Re: '33/'34 Sedan Delivery pass side tail light bracket.

Thank you for posting that.
I am pretty sure I will need to fabricate one. I did one for a '36 sedan delivery years ago and this one looks similar.
Forum: Early V8 (1932-53) 06-15-2020, 11:31 PM
Replies: 5
Views: 302
Posted By 95476
Re: 1940 Ford open car rear window frame

I am amazed at the amount of items that Lebarron Bonney sold that are no longer available.What a shame.
Forum: Early V8 (1932-53) 06-15-2020, 11:29 PM
Replies: 21
Views: 1,198
Posted By 95476
Re: Do the old style bubble balancer work

I picked up one of the old bubble balancers when a local shop was closing years ago. I used it many time. later on I was able to pick up a John Bean computer balancer. After I set it up I foid that...
Forum: Early V8 (1932-53) 06-14-2020, 11:55 PM
Replies: 10
Views: 1,291
Posted By 95476
Re: Walt Dupont

Best wishes for Walt.
Forum: Early V8 (1932-53) 06-13-2020, 11:34 PM
Replies: 12
Views: 557
Posted By 95476
'33/'34 Sedan Delivery pass side tail light bracket.

I saw somewhere that there was a man making right side tail light brackets for '33/'34 sedan deliveries.
I think the post was 4 or 5 years ago.
Does anyone know where one can be purchased ?
...
Forum: Early V8 (1932-53) 06-10-2020, 12:27 PM
Replies: 15
Views: 838
Posted By 95476
Re: Suggestions for rattle can base color 34 woodgraining?

Rustoleum Red Automotive Primer, black printers ink, brown printers ink, spray clear over it.
You can layer it you get the effect you want. Follow the directions on the can about recoating times. If...
Forum: Early V8 (1932-53) 06-10-2020, 12:16 PM
Replies: 6
Views: 358
Posted By 95476
Re: 1936 Cabriolet Convertible Tack Strip

I had the same problem on the last three converts I did.
I tried to patch the first one but it did not turn out well.
I ended up fabricating a new channel for each car.
I had to make it in three...
Forum: Early V8 (1932-53) 06-06-2020, 04:11 PM
Replies: 1
Views: 296
Posted By 95476
Anyone coming west from the Detroit area to Calif ?

I have a blown apart '34 Ford that needs to come to Sonoma,Calif from the Detroit ,Michigan area. The body is on a sturdy dolly and all the related parts are stuffed inside the car.
I know the...
Forum: Early V8 (1932-53) 05-29-2020, 12:03 PM
Replies: 2
Views: 313
Posted By 95476
Stumble off idle

I have a fresh 59AB that has a stumble on acceleration, like off of stop sign. It idles well and if you give it more gas when it stumbles it runs well. The spot just off idle seems to be the...
Forum: Early V8 (1932-53) 05-18-2020, 07:36 PM
Replies: 0
Views: 166
Posted By 95476
Engine pan ID

These were supposed to be for a '34 Ford but don't match any of the sets I have.
Any ideas what they fit ?
Thank you.
Forum: Early V8 (1932-53) 05-11-2020, 05:24 PM
Replies: 20
Views: 1,390
Posted By 95476
Re: Painting with Acrylic Enamel question

I ran into the same problem shooting Centari.
The guys at the paint shop sold me generic hardner and reducer.
It turned out just fine.
The generic was 1/2 the price of the DuPont products.
Forum: Early V8 (1932-53) 05-06-2020, 02:05 PM
Replies: 5
Views: 369
Posted By 95476
'34 Ford header panel brass grommets

I am trying to finish up my '34. I installed the windshield header panel and need to locate the brass grommets that go in the holes for the wiper motor controls.
I have not been able to find them on...
Forum: Early V8 (1932-53) 04-30-2020, 11:19 PM
Replies: 18
Views: 958
Posted By 95476
Re: '40 Disk/Drum brakes, no rear brake problem

I had a similar problem on a recent build. I used the normal Corvette 1 inch master cylinder but had little or no rear brake pressure. I went through the NAPA book and matched the rear wheel...
Forum: Early V8 (1932-53) 04-19-2020, 01:11 PM
Replies: 40
Views: 1,894
Posted By 95476
Re: Shipping a Columbia

I used engineshippers.com a few times and they were about 1/3 the price of the big carriers.
They shipped a '34 rear axle to me in Calif from Idaho for 200 bucks a while back.
With gas as lo as it...
Forum: Early V8 (1932-53) 04-19-2020, 11:45 AM
Replies: 7
Views: 713
Posted By 95476
Dupont/Axalta Centari enamel paint

I just found out that our local paint supplier for Centari is no longer selling it.
I have almost enough paint to finish my project, but one or two quarts short.
Does any one know of dealer that...
Forum: Early V8 (1932-53) 04-09-2020, 11:34 AM
Replies: 8
Views: 311
Posted By 95476
Re: 46 woody door skins

Robert Johnson Restorations
60 Clausing Court
Novato, Calif. 94945-4107
415-827-0524
Forum: Early V8 (1932-53) 04-06-2020, 09:06 PM
Replies: 10
Views: 632
Posted By 95476
Re: Sun Visor Repair

Call Acme in Long Beach. 562-437-0061 They should be able to help you. I just sent them the visors for the '34 project I am finishing up. ...
Showing results 1 to 25 of 269

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:00 AM.