Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 243
Search took 0.02 seconds.
Search: Posts Made By: Don S
Forum: Model A (1928-31) 01-30-2024, 06:39 PM
Replies: 2
Views: 262
Posted By Don S
Re: Oil pan gasket thickness

Thanks Synchro, I value your suggestion. It is still winter here, so I will get the job done but will have to report on the results in a couple of months.
Don S
Forum: Model A (1928-31) 01-30-2024, 12:23 PM
Replies: 2
Views: 262
Posted By Don S
Oil pan gasket thickness

I have some 3/32” urethane/ cork gasket material that I would like to use for a pan gasket.Can’t find the recommended thickness ,any ideas ? Is 3/32” ok?
Thanks Don S
Forum: Model A (1928-31) 01-29-2024, 03:13 PM
Replies: 53
Views: 3,799
Posted By Don S
Re: Zenith will flood the engine constantly

Mike 1291 , you state in post #3 that your engine runs well at speed but dies when you take your foot off the accelerator. Same symptom happened to me while on a tour. I ran out of gas near a gas...
Forum: Model A (1928-31) 01-15-2024, 04:59 PM
Replies: 56
Views: 2,742
Posted By Don S
Re: Question about using Brumfield head

Interesting comments about Brumfield heads . I purchased a 5.9 head from Larry in 2006, including a set of bolts and nuts . I have driven over 20000 miles since then with no head issues . Larry’s...
Forum: Model A (1928-31) 11-21-2023, 12:36 PM
Replies: 24
Views: 2,627
Posted By Don S
Re: Southern Ca banger machine shop?

Syncro99, the repair shop in Kelowna , is K&S Machine , the owner is Keith Korecki. He did the insert work etc on my engine about 20 years ago ,no issues. He has a very busy shop ,does a lot of drag...
Forum: Model A (1928-31) 11-08-2023, 03:00 PM
Replies: 8
Views: 838
Posted By Don S
Re: Rubber protection against suns radiation

Years ago there was a product used to protect rubber seals etc. I checked and it is still being manufactured in the states by American Grease, Ru Glyde is the product name. It is mainly used when...
Forum: Model A (1928-31) 10-11-2023, 11:53 AM
Replies: 55
Views: 14,697
Posted By Don S
Re: Does your Coupe have a Trunk or Rumble seat

Yes I put a rumble seat in my 31 deluxe coupe, car was all pieces when I started the restoration in 1981. There has been 4 generations of our family that have ridden in the rumble seat, including our...
Forum: Model A (1928-31) 04-08-2023, 01:31 PM
Replies: 26
Views: 4,549
Posted By Don S
Re: Looking for options on modern points and condenser

I have the same points and capacitor in my collection of spares. I think that I acquired it in the 80’s but never used it. I still have the box and a sketch of the parts together,but no directions of...
Forum: Model A (1928-31) 12-11-2022, 01:19 PM
Replies: 14
Views: 2,938
Posted By Don S
Re: 1931 Ford, Trunk or Rumble???

My grandkids , now their kids ,(my great grandkids , ) love the rumble seat. It takes them to our favourite ice cream shop. It is about a half hour ride along a lake at slow speed with little traffic...
Forum: Model A (1928-31) 11-30-2022, 02:38 PM
Replies: 16
Views: 2,417
Posted By Don S
Re: Coupe top question

Definitely someone’s fix, but not the way it should be. There should not be any covering on the visor as was done on earlier models. The later coupes have a squarish opening in the framing of the...
Forum: Model A (1928-31) 08-28-2022, 11:44 AM
Replies: 347
Views: 200,890
Posted By Don S
Re: F150 tranny with overdrive

Continuing with the installation of the Tremac transmission, I have had mine for several years now, love it , but am concerned that there is no rear tranny support . The original tranny had a rubber...
Forum: Model A (1928-31) 06-06-2022, 05:08 PM
Replies: 64
Views: 8,112
Posted By Don S
Re: WD40 as hand cleaner

WD 40 is really good to kill wasps. Keep the red tube attached to the can for accuracy and results .
Don
Forum: Model A (1928-31) 05-12-2022, 09:49 AM
Replies: 37
Views: 6,304
Posted By Don S
Re: B Carb on an A?

Question on the b carb gav housing that is pressed in, how is it removed for cleaning out the passages where the spring is etc. ?,also my carb is the B1 with the round float,worth rebuilding ,or...
Forum: Model A (1928-31) 05-11-2022, 02:05 PM
Replies: 7
Views: 1,526
Posted By Don S
Re: Dave Renners

Thanks Carl, phone numbers and e- mail address are the same as I used,I will have to be patient. Thanks,
Don
Forum: Model A (1928-31) 05-11-2022, 01:33 PM
Replies: 7
Views: 1,526
Posted By Don S
Re: Dave Renners

Bob C , the address you suggested does not work for me,any suggestion ?
Don
Forum: Model A (1928-31) 05-11-2022, 12:27 PM
Replies: 7
Views: 1,526
Posted By Don S
Re: Dave Renners

The e-mail address that I have rennerscorner.com does not work, any update?
Thanks Don
Forum: Model A (1928-31) 05-11-2022, 11:34 AM
Replies: 7
Views: 1,526
Posted By Don S
Dave Renners

Has any body heard from Dave Renner lately ? I have phoned and left messages but no reply .
Thanks
Forum: Model A (1928-31) 12-06-2021, 12:16 PM
Replies: 67
Views: 11,280
Posted By Don S
Re: Hagerty Insurance

In British Columbia, the only restrictions are on Vintage plates , they can only be used for sanctioned club events, weddings, graduations . I did not realize that taking the grandkids for ice cream...
Forum: Model A (1928-31) 11-23-2021, 12:48 PM
Replies: 18
Views: 2,814
Posted By Don S
Re: rubber boots

Interesting info for judging purposes, rubber pedal covers and spare tire covers are to be removed prior to judging. So you can use them just don't show them .
Forum: Model A (1928-31) 11-19-2021, 10:05 PM
Replies: 5
Views: 1,254
Posted By Don S
Re: List of businesses ,suppliers of parts , clubs, etc

Thanks guys , google it is. I can see that keeping that much information current would be a large task. I appreciated the use of it while it was available.
Don S
Forum: Model A (1928-31) 11-19-2021, 12:17 PM
Replies: 5
Views: 1,254
Posted By Don S
List of businesses ,suppliers of parts , clubs, etc

I must have been under a rock for a bit , but what happened to the library of all those talented people ,model a support businesses ,clubs etc that were at the beginning of our opening page, along...
Forum: Model A (1928-31) 02-20-2021, 01:25 PM
Replies: 49
Views: 10,982
Posted By Don S
Re: Wrap the steering wheel with rope?

I wet sanded my steering wheel with a very fine sand paper ,then scotchbrite pad and water to get a uniform mat finish . Spray your wheel with a satan urethane product from your local paint or...
Forum: Model A (1928-31) 02-15-2021, 12:59 PM
Replies: 5
Views: 855
Posted By Don S
Re: Shock ID

Ordsgt , , I have had the same set of shocks on my car since the early eighties. They have been ok and still don't leak .The curiosity for me was the 2 piece needle valve . Not sure how it works ,...
Forum: Model A (1928-31) 02-03-2021, 01:48 PM
Replies: 89
Views: 9,760
Posted By Don S
Re: A question for old guys

I feel badly for those of you that are challenged in one way or another. Working on our cars is part of who we are, to only be able to look at them would be dissapointing,and potentially not reason...
Forum: Model A (1928-31) 01-15-2021, 01:16 PM
Replies: 34
Views: 3,661
Posted By Don S
Re: whats the best & worst car to buy in 1930

I bought my uncles 32 Chev sedan in 1955 ,to drive to school. Nice car , but rear axels were prone to break as mine did only a month after I got it. Only went over a bump in the road, and that was...
Showing results 1 to 25 of 243

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:27 PM.