Forum: Early V8
12-19-2016, 03:20 PM
|
Replies: 0
Views: 1,078
51 Fordomatic torque converter
Hello group,
I'm looking for a 51 Fordomatic torque converter hub to drive the front pump. Although, I would take the entire torque converter should anyone know of one available. Any leads would be...
|
Forum: Early V8 (1932-53)
10-31-2016, 03:21 PM
|
Replies: 5
Views: 1,143
|
Forum: Early V8 (1932-53)
10-31-2016, 12:00 PM
|
Replies: 5
Views: 1,143
51 Fordomatic shift ranges?
I recently installed a rebuilt Fordomatic in my 51 Victoria. My porobem is it will not shift into 3rd. gear until about 50 MPH. Any ideas what is the cause and how to fix it? What are the normal...
|
Forum: Early V8
10-21-2016, 11:58 AM
|
Replies: 0
Views: 969
|
Forum: Early V8 (1932-53)
08-16-2016, 07:00 PM
|
Replies: 3
Views: 1,295
|
Forum: Early V8 (1932-53)
08-16-2016, 04:49 PM
|
Replies: 3
Views: 1,295
51 Fordomatic torque converter hub needed
Does anyone have or know where I can locate the hub piece on a 51 Fordomatic torque converter? This would be the driver for the front pump. It seems that the 51 had a longer reach than later models....
|
Forum: Early V8 (1932-53)
07-22-2016, 07:03 PM
|
Replies: 4
Views: 1,073
|
Forum: Early V8 (1932-53)
07-22-2016, 04:53 PM
|
Replies: 4
Views: 1,073
|
Forum: Early V8 (1932-53)
07-22-2016, 02:40 PM
|
Replies: 4
Views: 1,073
|
Forum: Early V8 (1932-53)
06-26-2016, 04:23 PM
|
Replies: 2
Views: 858
|
Forum: Early V8 (1932-53)
06-26-2016, 08:00 AM
|
Replies: 2
Views: 858
51 Victoria hood trim needed
I seem to have misplaced the trim piece located on the center of the hood from front to back during the restoration on a 51 Victoria. Does anyone know where I locate a replacement? I think that it is...
|
Forum: Early V8 (1932-53)
06-26-2016, 07:43 AM
|
Replies: 5
Views: 2,335
Re: 51 Ford-o-matic torque converter issues
As a follow up on the issue, I found that the difference of the converters was that the 51 converter hub was 1/2" + - longer than the 52 due to the front pump drive gear cogs were located near the...
|
Forum: Early V8 (1932-53)
06-17-2016, 06:43 AM
|
Replies: 5
Views: 2,335
|
Forum: Early V8 (1932-53)
06-16-2016, 09:44 AM
|
Replies: 5
Views: 2,335
51 Ford-o-matic torque converter issues
Hello all, new member here. I have a 51 Vic. with the Ford-o-matic. While removing the converter from the transmission, I noticed that one ear was broken off from the hub that drives the front pump...
|
Forum: Late V8 (1954+)
06-07-2016, 11:25 AM
|
Replies: 6
Views: 3,038
Re: Ford-o-matic Help!
I agree sounds like a linkage adjustment required. Does anyone have any tips as to how to remove the clutch piston in the rear clutch assembly on a 51 model fordomatic. I tried air pressure on the...
|