Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 88
Search took 0.01 seconds.
Search: Posts Made By: Lowell Fast
Forum: Model T (1909-1927) 12-01-2018, 10:48 AM
Replies: 8
Views: 2,371
Posted By Lowell Fast
Re: Rear Axle Housing woes

When I removed the rear wheels on my 13, the brake shoes were missing and one axel was shaft was shimmed.
I install rebuilt , lined brake shoes . The wheels are hitting the shoes . That may be why...
Forum: Model T (1909-1927) 08-07-2018, 11:48 PM
Replies: 2
Views: 843
Posted By Lowell Fast
Early Aluminum Hoods

How did the finish hold up on the early Aluminum hoods compared to the finishes on the steel components of the body and fenders ?

Any source for photos of the aged finish on such hoods where the...
Forum: Model T (1909-1927) 07-11-2018, 08:50 PM
Replies: 5
Views: 1,291
Posted By Lowell Fast
Re: Brass Radiator emblem

The fins on my old brass original radiator on my 13 has the "shadow" of a Ford emblem that was removed long ago . My 14 has no evidence of ever having a Ford emblem although the original owner had...
Forum: Model T (1909-1927) 07-08-2018, 12:54 PM
Replies: 5
Views: 1,291
Posted By Lowell Fast
Brass Radiator emblem

Was the Brass Ford Radiator emblem an accessory on early Ts ?
Forum: Model T (1909-1927) 07-03-2018, 11:10 AM
Replies: 1
Views: 713
Posted By Lowell Fast
Intake manifold Gaskets for 1913

I have found that the 1912 and 1913 had Aluminum intake manifolds that had protuberances that entered into the intake port on the block casting .The copper crush gaskets for later models will not...
Forum: Model A (1928-31) 06-13-2018, 09:58 AM
Replies: 15
Views: 6,702
Posted By Lowell Fast
Re: Edison Spark Plugs

I have some Edison 37 TS plugs . Do they fit any Ford engine ?
Forum: Model T (1909-1927) 02-07-2018, 09:38 AM
Replies: 9
Views: 3,816
Posted By Lowell Fast
Re: How does oil get to the main bearings and lifters?

How do you get at the "oil feed tube" to clear or clean it .?
Forum: Model T (1909-1927) 02-03-2018, 12:23 AM
Replies: 5
Views: 1,108
Posted By Lowell Fast
Re: Natural spoke wheels

Thanks. It seems all the brass Ts have seen had the black paint removed from the wooden spokes .
Forum: Model T (1909-1927) 02-02-2018, 07:39 PM
Replies: 5
Views: 1,108
Posted By Lowell Fast
Re: Natural spoke wheels

I did not state my question clearly . I was wondering when the Natural Finished spoke wheel ended and the black painted spokes started .
Forum: Model T (1909-1927) 02-02-2018, 12:38 AM
Replies: 5
Views: 1,108
Posted By Lowell Fast
Natural spoke wheels

What was the last year for the Natural spoke wheels ?
Forum: Model T (1909-1927) 01-27-2018, 11:25 PM
Replies: 10
Views: 3,015
Posted By Lowell Fast
Re: Low mileage original T

I have a 1913 with what I think are the original floorboards. There is a 4"x 4" cutout in the floorboard below the speedometer on the passenger's side . Why would anyone have done this?
Forum: Model A (1928-31) 12-09-2017, 10:45 PM
Replies: 3
Views: 707
Posted By Lowell Fast
Re: Fuel Tank

After checking my other tank the device appears to be a device for plugging a leak.
Forum: Model A (1928-31) 12-03-2017, 11:53 PM
Replies: 3
Views: 707
Posted By Lowell Fast
Re: Fuel Tank

341052


What is this in the bottom of my gas tank ?
Forum: Model A (1928-31) 12-03-2017, 02:38 PM
Replies: 3
Views: 707
Posted By Lowell Fast
Fuel Tank

Cleaning fuel tank on 31 coupe. On the bottom of the interior of the tank there is a flat 4 '' x 1/2" device. It lays flat and appears to go through the bottom of the tank and is oriented...
Forum: Model A (1928-31) 11-25-2017, 11:34 AM
Replies: 41
Views: 5,271
Posted By Lowell Fast
Re: persistent misfiring - help!

pigtail wire in the distributor and/or condenser are often culprits in a car that has been performing well before going bad.
You checked the compression but sometimes an exhaust valve may be...
Forum: Model A (1928-31) 11-19-2017, 08:34 PM
Replies: 8
Views: 1,064
Posted By Lowell Fast
Re: Timing A and B Models

I may not have been clear in my question on the B model Timing . I have timed my A models with the pin with no problems . A friend asked me to help him with his B Model which has been backfiring . I...
Forum: Model A (1928-31) 11-18-2017, 11:07 PM
Replies: 8
Views: 1,064
Posted By Lowell Fast
Timing A and B Models

Are A and B models static timed the same ? On the B does the pinset give you the increased advance the B requires . Read the instructions and timed B but getting bad back firing .
Forum: Model A (1928-31) 05-31-2017, 10:57 PM
Replies: 31
Views: 7,177
Posted By Lowell Fast
Re: Water Pump Replacement

What are "Fake Studs" ?
Forum: Model A (1928-31) 04-22-2017, 10:43 AM
Replies: 16
Views: 2,471
Posted By Lowell Fast
Re: hood support...dummy needs help

When I heard that 2nd
dropping sound" , I suspected "the worst" . I thought 2 screws were more easy than the support rods and radiator hoses but ; "Bit Again" .
Forum: Model A (1928-31) 04-21-2017, 11:36 PM
Replies: 16
Views: 2,471
Posted By Lowell Fast
Re: hood support...dummy needs help

I was removing the rear part that retains the hood hinge pin (I needed to remove the hood) .
When I removed the first machine screw , I heard something drop beneath the car . I thought I knocked a...
Forum: Model A (1928-31) 04-09-2017, 09:49 AM
Replies: 34
Views: 4,520
Posted By Lowell Fast
Re: Best way to enter and exit 31 CCPU

How does one get out of the Rumble Seat ?
Forum: Model A (1928-31) 01-18-2017, 09:05 PM
Replies: 3
Views: 993
Posted By Lowell Fast
Re: Sills

1930 Model A Roadster
Forum: Model A (1928-31) 01-18-2017, 09:42 AM
Replies: 3
Views: 993
Posted By Lowell Fast
Sills

How are the body panels attached to the body Sills ?
Forum: Model A (1928-31) 11-25-2016, 10:51 PM
Replies: 35
Views: 6,269
Posted By Lowell Fast
Re: cowell lights

"cowl wiring had a SWITCH mounted system. the switch was part A13335 "

Where was this switch mounted ?
Forum: Model A (1928-31) 11-20-2016, 10:43 PM
Replies: 33
Views: 5,860
Posted By Lowell Fast
Re: Aluminum block almost finished.

Do you plan to sleeve the cylinders ?

I would not gamble all that work on Al bearing caps .
Showing results 1 to 25 of 88

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:29 PM.