Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 295
Search took 0.02 seconds.
Search: Posts Made By: dlfrisch
Forum: Model A (1928-31) 06-19-2020, 04:39 PM
Replies: 2
Views: 210
Posted By dlfrisch
Re: wood body blocks

Les Andrews Service / Maintenance book has pictures
Forum: Model A (1928-31) 06-14-2020, 08:10 PM
Replies: 1
Views: 299
Posted By dlfrisch
Re: Stationary Sport Coupe Fabric Top

Start new independent Thread
Forum: Model A (1928-31) 06-07-2020, 12:10 PM
Replies: 1
Views: 299
Posted By dlfrisch
Stationary Sport Coupe Fabric Top

I plan on purchasing a new top - most likely Cartouche. I talked to them and the new tops come with installation directions. The vehicle is still totally disassembled - body off project. It will be...
Forum: Model A (1928-31) 06-04-2020, 01:52 PM
Replies: 13
Views: 632
Posted By dlfrisch
Re: 1930-31 Convertible top patterns needed

Start a new #6 Thread if possible
Forum: Model A (1928-31) 06-04-2020, 01:48 PM
Replies: 13
Views: 632
Posted By dlfrisch
Sport Coupe fixed fabric top

Some what similar to the next Thread (convertible top patterns). I plan on purchasing the top - most likely from Cartouche. I am looking for help to make sure I install it correctly. Does anyone...
Forum: Model A (1928-31) 06-04-2020, 12:27 PM
Replies: 49
Views: 3,958
Posted By dlfrisch
Re: Take a gander at this.

A few years back - I saw A Pieten-pole being built....as it ended up, a pilot friend bought it and finished building it. In a few test flights some how he lost engine fuel and had a forced landing....
Forum: Model A (1928-31) 06-01-2020, 11:50 AM
Replies: 1
Views: 170
Posted By dlfrisch
Re: 29 Windshield help

Once the top section is removed and to remove the remainder or all of the glass - use a block of wood, a large hammer and pound away. I did the task - the windshield glass is very strong, but it...
Forum: Model A (1928-31) 05-26-2020, 12:07 PM
Replies: 13
Views: 740
Posted By dlfrisch
Re: Factory VIN - ID Numbers

Good information - thank’s
Forum: Model A (1928-31) 05-25-2020, 03:12 PM
Replies: 13
Views: 740
Posted By dlfrisch
Factory VIN - ID Numbers

I have the main body off of the frame - soda (sanded) and primed. I can’t find any manufacturers numbers / letters on the frame or cross members.
Forum: Model A (1928-31) 05-15-2020, 07:50 PM
Replies: 7
Views: 355
Posted By dlfrisch
Re: Advertisements

I just recently Posted (about a week ago) an inquiry noting the same situation. I reloged into The Barn - not sure if that solved the annoying advertising’s, but they did stop.
Forum: Model A (1928-31) 05-12-2020, 06:09 AM
Replies: 18
Views: 933
Posted By dlfrisch
Re: Advertisements

Nothing that big - I get small adds in between some Posts.....they come and go - I’ll manage.
Forum: Model A (1928-31) 05-11-2020, 09:47 PM
Replies: 18
Views: 933
Posted By dlfrisch
Re: Advertisements

Just nosing at some of the older Posts and in between the different requests I keep getting advertisements. I think I have to request to or contact “thread advertisements”
Forum: Model A (1928-31) 05-11-2020, 09:23 PM
Replies: 18
Views: 933
Posted By dlfrisch
Advertisements

Delete the annoying advertisements
Forum: Model A (1928-31) 05-01-2020, 08:23 PM
Replies: 12
Views: 830
Posted By dlfrisch
Re: Identifying Year Of Model A Frame

I’ll try to read the original model (mfg) numbers, once I have the body off. If, need be I will redo the original VIN - ID, take photo, then reinstall the body.
Forum: Model A (1928-31) 05-01-2020, 03:09 PM
Replies: 6
Views: 488
Posted By dlfrisch
Re: Planing to reassemble vehicle

Thanks for the tips.....I’m not quite ready yet. The main body is at the body/paint shop. I’m not even sure where they are with their work- soda sanding, some small body spots, prime and final...
Forum: Model A (1928-31) 04-30-2020, 04:20 PM
Replies: 6
Views: 488
Posted By dlfrisch
Planing to reassemble vehicle

Is there a sequence or procedure to drop the prepared and painted body on to the finished car frame. I know and must follow Les Andrews drawing - frame welt, side splash unit, body wood block and...
Forum: Model A (1928-31) 04-27-2020, 07:28 PM
Replies: 345
Views: 33,038
Posted By dlfrisch
Re: Just wondering : what's your year of birth ?

DOB. January 23, 1941. Can’t believe the number of my completed years - owned a few (3) Model A’s over those past years. I’m rebuilding (body off - frame up) a ‘28 Sport Coupe, as my current...
Forum: Model A (1928-31) 04-12-2020, 07:39 PM
Replies: 4
Views: 519
Posted By dlfrisch
Re: Radiator shroud fit question

Opps... l was refusing to the outer radiator chrome cover.
Forum: Model A (1928-31) 04-12-2020, 07:32 PM
Replies: 4
Views: 519
Posted By dlfrisch
Re: Radiator shroud fit question

The radiator had been replaced on my ‘28 Sport Coupe. I bought a new outer shroud. I had to trim (cut) the lower section a little bit adjusting it to fit in further- closer to the radiator, grind a...
Forum: Model A (1928-31) 04-10-2020, 07:45 PM
Replies: 7
Views: 364
Posted By dlfrisch
Re: Help - ‘28 Sport Coupe Windshield

Yes - I had to drill the two screws (one each side) trim the edges with a small chisel and hammer away. I did get top piece off. I’ll work on the rest tomorrow. Continue disassembling and figure...
Forum: Model A (1928-31) 04-10-2020, 05:10 PM
Replies: 7
Views: 364
Posted By dlfrisch
Help - ‘28 Sport Coupe Windshield

How do I disassemble and install new windshield glass ? The frame is removed from the vehicle and is on my work bench. It is real solid - I can’t move (separate) any of the frame, sides top or...
Forum: Model A (1928-31) 04-06-2020, 07:01 PM
Replies: 94
Views: 15,852
Posted By dlfrisch
Re: What is the hardest Model A accessory to find

While working on my steering column, I mistakenly threw away or accidentally dropped my top flange (the unit with the notches in it for spark/gas) in the trash basket. Searching to replace the part...
Forum: Model A (1928-31) 04-06-2020, 12:52 PM
Replies: 0
Views: 133
Posted By dlfrisch
Installing a 1928 Sport Coupe Top

As per Post 4/6/2020 - How to replace a stock OEM roof (Eccentric Old Guy) and as referenced to - CHuDWah # 2 replied : http:web.archive.org/web20190128

Does anyone have a similar YouTube or...
Forum: Model A (1928-31) 04-03-2020, 10:09 PM
Replies: 13
Views: 756
Posted By dlfrisch
Re: Installing the control rods

Again-thanks....I did use anti rattlers. Rich in Tucson, what are metal handles of disposable flex bushings? dlfrisch@gmail.com
Forum: Model A (1928-31) 04-03-2020, 04:37 PM
Replies: 13
Views: 756
Posted By dlfrisch
Re: Installing the control rods

Thanks friends- there are NO internal guide tubes and the top bearing was in alinement- time after time. Jackson111 said, keep trying, but I could not find either hole. I finely slid two #24 bell...
Showing results 1 to 25 of 295

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:38 PM.