Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Drive Shaft Dave
Forum: Early V8 (1932-53) 02-02-2019, 08:34 PM
Replies: 11
Views: 764
Posted By Drive Shaft Dave
Re: What is this puller part for ???

The puller is used to remove rear drums and hub from tapered axle shafts. I didn't read the compete thread . I dont know what the other part is. Tried to delete but wouldn't take.
Forum: Model A (1928-31) 02-02-2019, 08:30 PM
Replies: 46
Views: 2,368
Posted By Drive Shaft Dave
Re: Ford Tri-Motor

Actually the Harvard was a different airplane, although a trainer with fixed gear.
Forum: Model A (1928-31) 02-01-2019, 09:10 PM
Replies: 12
Views: 605
Posted By Drive Shaft Dave
Re: Engine mount rubber replacement

Brattons cataloge pg. 35, 2018, shows motor mount rubbers made to the Ford print. while I have not tried these, the last mount 's I put in , made use of some dish soap and they slid in quite...
Forum: Model A (1928-31) 01-14-2019, 12:14 AM
Replies: 2
Views: 255
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 01-07-2019, 12:24 AM
Replies: 42
Views: 1,879
Posted By Drive Shaft Dave
Re: Water Temperature Gauge

I have heard that the rex aco temp gauge has been problematic in the last few years .
Forum: Model A (1928-31) 01-07-2019, 12:09 AM
Replies: 8
Views: 1,400
Posted By Drive Shaft Dave
Re: Tom Wesenberg

Yes he is ok. just taking a look around the country side.
Forum: Model A (1928-31) 12-07-2018, 08:11 PM
Replies: 1
Views: 237
Posted By Drive Shaft Dave
Re: Need clarification...Bolts and Toggle Lever...

fine thread on the Spring Bolts, Toggle lever , drive in.
Forum: Model A (1928-31) 12-06-2018, 11:20 PM
Replies: 56
Views: 2,691
Posted By Drive Shaft Dave
Re: Weld and grind roller tracks

It is more of a hassle to replace them , weld then file or use die grinder.
Forum: Model A (1928-31) 12-02-2018, 01:54 AM
Replies: 11
Views: 869
Posted By Drive Shaft Dave
Re: 7.0 Earthquake in Anchorage Alaska

Alaska had a bad one in 1964 I remember. Was 9.2 on the Richter scale.
Forum: Model A (1928-31) 11-28-2018, 12:32 AM
Replies: 5
Views: 528
Posted By Drive Shaft Dave
Re: Tail pipe stub

Muffler shop could make one.
Forum: Model A (1928-31) 11-28-2018, 12:30 AM
Replies: 57
Views: 3,694
Posted By Drive Shaft Dave
Re: Stroke

Hang in there Bill!
Forum: Model A (1928-31) 10-18-2018, 10:10 PM
Replies: 8
Views: 597
Posted By Drive Shaft Dave
Re: Ignition switch

Disconnect the light and horn wire from the cut out then try it, you most likely have socket grounded .
Forum: Model A (1928-31) 09-21-2018, 01:16 PM
Replies: 23
Views: 1,835
Posted By Drive Shaft Dave
Re: coils question

How about Chev 6 cyl. they were always mounted terminals down.
Forum: Model A (1928-31) 09-21-2018, 12:26 AM
Replies: 18
Views: 1,147
Posted By Drive Shaft Dave
Re: Fan Blade advice.

make shure you use a flat steel washer under the mounting nut on an aluminum fan.
Forum: Model A (1928-31) 09-21-2018, 12:12 AM
Replies: 15
Views: 1,073
Posted By Drive Shaft Dave
Re: Another Gas Tank and Headlight question

If you put in sealer there will come a day you wish you hadn't.
Forum: Model A (1928-31) 09-06-2018, 11:32 PM
Replies: 3
Views: 544
Posted By Drive Shaft Dave
Smile Re: Might have screwed up

I doubt that you hurt anything.:)
Forum: Model A (1928-31) 08-22-2018, 11:50 PM
Replies: 20
Views: 1,438
Posted By Drive Shaft Dave
Re: Is this an 'A'?

I't is a Chevrolet.
Forum: Model A (1928-31) 08-18-2018, 12:27 AM
Replies: 14
Views: 956
Posted By Drive Shaft Dave
Re: Original ammeter or repop?

I bought one of those on flea bay a few years back, had the bezel nickle plated.
Forum: Model A (1928-31) 08-07-2018, 12:27 AM
Replies: 13
Views: 1,024
Posted By Drive Shaft Dave
Re: Another spark plug question

I also used the TT- 10, then switched to the hotter W-18. The TT-10 is too cold of a heat range.
Forum: Model A (1928-31) 07-31-2018, 12:41 AM
Replies: 82
Views: 11,518
Posted By Drive Shaft Dave
Re: New Doodlebug Owner

I like what you have done so far ,but I would like to see the original starter on it.:D
Forum: Model A (1928-31) 07-30-2018, 11:14 PM
Replies: 10
Views: 994
Posted By Drive Shaft Dave
Re: Cupola questions

It looks like more than just a head nut leaking.
Forum: Model A (1928-31) 07-29-2018, 12:43 AM
Replies: 14
Views: 1,061
Posted By Drive Shaft Dave
Re: Steering Wheel removal

I think that is a soy bean wheel.
Forum: Model A (1928-31) 05-25-2018, 10:16 PM
Replies: 19
Views: 2,054
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 05-25-2018, 10:11 PM
Replies: 13
Views: 850
Posted By Drive Shaft Dave
Re: Help Needed - Sediment Bowl Gasket Dimensions

I would think that if you had some 1/8 gasket material, it would work fine.
Forum: Model A (1928-31) 04-28-2018, 12:07 AM
Replies: 3
Views: 441
Posted By Drive Shaft Dave
Re: speedometer cable and gear box questions

Two bolts at the bottom of the torque tube and it will drop right off.1/4 inch bolts. Yes it takes a gasket. What book were you reading?
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:05 AM.