Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: brum1
Forum: Model A (1928-31) Today, 06:58 AM
Replies: 4
Views: 139
Posted By brum1
Re: Ignition cylinder removal

Thank guys, just what I needed to see,

Regards
Forum: Model A (1928-31) Yesterday, 08:23 PM
Replies: 4
Views: 139
Posted By brum1
Ignition cylinder removal

In the process of replacing the original lock cylinder as it only had 1 key. I have removed from housing and it is not obvious how to remove the cylinder itself?
I have a replicate with 2 keys I...
Forum: Model A (1928-31) 01-19-2021, 06:15 AM
Replies: 10
Views: 472
Posted By brum1
Re: Manifold Heater Mount

Thanks Fred, what is securing the heater to the manifold(other than the hose)

Is your manifold a stock round body?
Forum: Model A (1928-31) 01-18-2021, 03:58 PM
Replies: 2
Views: 250
Posted By brum1
Re: Rear Fender Assembly

Thanks Dennis, I will take a closer look for those spot welds
Forum: Model A (1928-31) 01-18-2021, 03:56 PM
Replies: 10
Views: 472
Posted By brum1
Re: Manifold Heater Mount

Thanks Guys, I will give this another look, if anyone does have a picture of this type installed that would be great
Forum: Model A (1928-31) 01-18-2021, 11:24 AM
Replies: 2
Views: 250
Posted By brum1
Rear Fender Assembly

Have some rust at base of rear fender(inside) where bolts attach to running board. Looks like a separate piece of sheet metal but not sure? Can this piece be removed separately or is it an integral...
Forum: Model A (1928-31) 01-17-2021, 03:42 PM
Replies: 10
Views: 472
Posted By brum1
Re: Manifold Heater Mount

Thanks Guys, Yes I have seen those waffle style, unfortunately my car does not have one at the moment
Forum: Model A (1928-31) 01-17-2021, 11:11 AM
Replies: 10
Views: 472
Posted By brum1
Manifold Heater Mount

I acquired this manifold heater with the car. How do these typically mount to the exhaust manifold? This heater has two through bolts as shown in the picture? Appreciate any insight
Forum: Model A (1928-31) 01-14-2021, 08:13 PM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Thanks Ed, that is exactly how I proceeded, went together well and back on the road!
Forum: Model A (1928-31) 01-14-2021, 07:17 AM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Good point, the car does seem to sit a bit higher in the front, worth a check
Forum: Model A (1928-31) 01-12-2021, 05:48 PM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Thanks for all the feedback,

the problem was resolved by removing U-bolts, dropping axel, and assembling shackles 1st. Axle was then jacked up and U-bolts assembled.

You would think it would...
Forum: Model A (1928-31) 01-09-2021, 06:46 PM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Thanks for the feedback.

I will remove U-bolts and lower axle with Jack. probably remove wishbone rear mount as well.

Assemble shackles to spring with spreader and hopefully everything will...
Forum: Model A (1928-31) 01-09-2021, 05:00 PM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Yes, the U bolts we tightened 1st and then I went to shackles,

the axle and wishbone look in good shape(undamaged) and the old spring was fine front to back (shackles were bolted up fine, old...
Forum: Model A (1928-31) 01-09-2021, 04:34 PM
Replies: 16
Views: 1,317
Posted By brum1
Re: A bad day!!

Don't know if it was in accident, overall in great shape
Forum: Model A (1928-31) 01-09-2021, 04:15 PM
Replies: 16
Views: 1,317
Posted By brum1
A bad day!!

Installed a new front spring only to find the drivers side not aligned with the perch(front to back) off by 1". Shackle goes through perch fully but not spring eyelet. Passenger side OK, center bolt...
Forum: Model A (1928-31) 01-02-2021, 06:10 AM
Replies: 20
Views: 1,026
Posted By brum1
Re: Bendix Drive Question??

Thanks for the feedback as I had not seen one before
Forum: Model A (1928-31) 01-01-2021, 06:48 PM
Replies: 20
Views: 1,026
Posted By brum1
Bendix Drive Question??

anyone seen this type of bendix drive? Pros/Cons compared to exposed spring?
Forum: Model A (1928-31) 06-20-2020, 01:57 PM
Replies: 4
Views: 756
Posted By brum1
Forum: Model A (1928-31) 06-19-2020, 07:50 PM
Replies: 4
Views: 756
Posted By brum1
Best Trunk in the market

Looking to purchase a straight back trunk and rack for my 30 town sedan. Any opinion on the vendor with the best quality product? Your feedback is appreciated:)
Forum: Model-A 06-14-2020, 03:21 PM
Replies: 1
Views: 658
Posted By brum1
Forum: Early V8 02-24-2020, 03:45 PM
Replies: 1
Views: 309
Posted By brum1
Re: Restoration Shop Manual**NEW**

Currently sold to antique auto hobbyist, auto shops, and fabricators, take a look
Forum: Model-A 02-24-2020, 03:44 PM
Replies: 2
Views: 596
Posted By brum1
Re: Restoration Shop Manual**New**

Currently sold to antique auto hobbyist, auto shops, and fabricators, take a look
Forum: Model-T 02-24-2020, 03:42 PM
Replies: 1
Views: 1,456
Posted By brum1
Re: Restoration Shop Manual**New**

Currently sold to antique auto hobbyist, auto shops, and fabricators, take a look
Forum: Model A (1928-31) 02-01-2020, 11:28 AM
Replies: 1
Views: 383
Posted By brum1
Model A fasteners

Does anyone have a bolt map for the model A similar to the model T map attached?? Also, how many fasteners where used in the model A??
Forum: Model-A 01-30-2020, 06:56 PM
Replies: 2
Views: 596
Posted By brum1
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:11 AM.