Forum: Early V8 (1932-53)
12-20-2018, 04:16 PM
|
Replies: 12
Views: 1,783
|
Forum: Early V8 (1932-53)
07-01-2018, 08:32 PM
|
Replies: 32
Views: 8,540
|
Forum: Early V8 (1932-53)
03-21-2017, 04:01 PM
|
Replies: 4
Views: 1,119
32 peddle arm alignment
Should peddle arm be heated in bending to make inch adjustments . Or can they be bent while in the chassis without heating. Having trouble installing wood toe board and peddle arms are not lining up...
|
Forum: Early V8 (1932-53)
02-27-2017, 03:01 PM
|
Replies: 4
Views: 1,615
Re: Weatherhead 1512 & oil filter
Thanks JSeery.
All of the fittings you listed have the .065 restriction but they all have 1/8 NPT female end. That is the same as the weatherhead 1512 that I have.
I was under the...
|
Forum: Early V8 (1932-53)
02-25-2017, 03:48 PM
|
Replies: 4
Views: 1,615
|
Forum: Early V8 (1932-53)
02-25-2017, 01:31 PM
|
Replies: 4
Views: 1,615
Weatherhead 1512 & oil filter
Located a Weatherhead 1512 fitting with the small restricter hole to use on my oil filter. What size tubing and fittings are used with the 1512? From the female end of fitting it looks like it...
|
Forum: Early V8 (1932-53)
02-11-2017, 06:52 PM
|
Replies: 8
Views: 2,702
Re: 32 Vintique Fuel Tank question
Checked clearance of sending unit post and it is not touching floor. Pick up tube assembly which is a repop and it seems to be touching floor. I do have shims under the last two body mount bolts on...
|
Forum: Early V8 (1932-53)
02-11-2017, 11:57 AM
|
Replies: 8
Views: 2,702
32 Vintique Fuel Tank question
Has anyone had problems with sending unit in Vintique fuel tank not allowing body to fully rest on frame rails? if so, any suggestions
|
Forum: Early V8
02-08-2017, 04:19 PM
|
Replies: 1
Views: 896
|
Forum: Early V8
02-08-2017, 11:14 AM
|
Replies: 1
Views: 896
32 rear window metal channel
I need two of the rear window channels that hold the vertical window runs in a 32 5-window coupe. The picture below is what I need two of, I understand these are approximately 4 inches long and...
|
Forum: Early V8 (1932-53)
02-07-2017, 06:10 PM
|
Replies: 7
Views: 1,118
|
Forum: Early V8 (1932-53)
02-07-2017, 11:36 AM
|
Replies: 7
Views: 1,118
|
Forum: Early V8 (1932-53)
02-06-2017, 09:23 PM
|
Replies: 7
Views: 1,118
|
Forum: Early V8 (1932-53)
02-06-2017, 03:32 PM
|
Replies: 7
Views: 1,118
32 5-window rear window questions
Had the package tray and window mechanism apart for several years for repairs and paint. Does the two wood vertical stanchions have two sheet metal channels that holds the window runs in place? It...
|
Forum: Early V8 (1932-53)
01-07-2017, 09:47 AM
|
Replies: 2
Views: 1,111
|
Forum: Early V8 (1932-53)
12-25-2016, 02:15 PM
|
Replies: 2
Views: 1,096
1932 grill shell stainless trim
How tight do you tighten the two threaded rods that come off each leg of the stainless trim on the radiator grill shell? I want to pull trim down tight to the grill shell but don't want to break the...
|
Forum: Early V8 (1932-53)
12-23-2016, 02:15 PM
|
Replies: 19
Views: 3,162
|
Forum: Early V8 (1932-53)
07-13-2016, 09:41 AM
|
Replies: 8
Views: 1,659
|
Forum: Early V8 (1932-53)
07-11-2016, 09:26 PM
|
Replies: 8
Views: 1,659
59AB in 32-Chatter rods
Have stock 32 front mounts on 59 AB. In using 32 v-8 chatter rods with this engine, do you tighten the nut snug or do you tighten it til there is not space between rod shoulder and block? Or, should...
|
Forum: Early V8 (1932-53)
03-28-2016, 09:34 PM
|
Replies: 7
Views: 1,190
|
Forum: Early V8 (1932-53)
11-23-2015, 07:41 PM
|
Replies: 4
Views: 1,614
|
Forum: Early V8 (1932-53)
11-17-2015, 09:22 PM
|
Replies: 3
Views: 1,359
U-joint Cup-small hole
In assembling the u-joint cup, does the side of the cup with the small hole go down or up?
|
Forum: Early V8 (1932-53)
09-30-2015, 02:50 PM
|
Replies: 15
Views: 2,418
Re: 6 volt
this forum should help you http://ytmag.yesterdaystractors.com/cgi-bin/boards.cgi
|
Forum: Early V8 (1932-53)
09-25-2015, 11:02 AM
|
Replies: 40
Views: 6,172
|
Forum: Early V8 (1932-53)
09-16-2015, 11:41 AM
|
Replies: 3
Views: 1,078
|