Forum: Early V8 (1932-53)
12-14-2023, 02:30 PM
|
Replies: 29
Views: 15,284
|
Forum: Early V8 (1932-53)
12-14-2023, 11:00 AM
|
Replies: 29
Views: 15,284
Re: Trautwein Products Window Frames
I ordered one for my 34 about 10 days ago (dec 5 2023) , sent him a money order ( they don't do cards), and tried to call for 2 days now to see if they got it ok but can't get answer anywhere....
|
Forum: Early V8 (1932-53)
03-11-2023, 02:23 PM
|
Replies: 5
Views: 892
|
Forum: Early V8 (1932-53)
03-11-2023, 01:35 AM
|
Replies: 5
Views: 892
|
Forum: Early V8 (1932-53)
03-10-2023, 05:02 PM
|
Replies: 5
Views: 892
|
Forum: Early V8
07-30-2022, 03:48 PM
|
Replies: 0
Views: 760
Duval header for 32 Ford Roadster
Building a top frame for your 32 Ford roadster with a Duval windshield? I have a 2 piece cast aluminum windshield header perfect for your application. It comes apart in the center and from your...
|
Forum: Early V8
03-28-2022, 01:19 PM
|
Replies: 0
Views: 257
Windshield header for Duval WS
Building a top frame for your 32 Ford roadster with a Duval windshield? I have a 2 piece cast aluminum windshield header perfect for your application. It comes apart in the center and from your top...
|
Forum: Early V8 (1932-53)
07-08-2018, 10:03 AM
|
Replies: 22
Views: 4,764
Re: Pertronix distributer kit
Thanks. Mine is 12 volts with a GM alternator. You're "the electrical guy" , what coil should I run with the Pertronics IF I decide to use it? Thanks again !
|
Forum: Early V8 (1932-53)
07-07-2018, 10:42 PM
|
Replies: 22
Views: 4,764
|
Forum: Early V8 (1932-53)
07-07-2018, 08:16 PM
|
Replies: 22
Views: 4,764
Pertronix distributer kit
I have a 39 flathead in my 36 coupe and am thinking of putting in a Pertronix kit to get rid of the points etc, because I seem to always have misses and ignition problems. Anyone used their kit?...
|
Forum: Early V8 (1932-53)
01-29-2018, 07:31 PM
|
Replies: 9
Views: 1,492
Logo color on 48 MERC cap
Does anyone know what the correct color(s) are / is for the logo on the hubcaps for a '48 Merc? Thanks!
|
Forum: Early V8 (1932-53)
06-18-2017, 12:03 AM
|
Replies: 6
Views: 1,239
|
Forum: Early V8 (1932-53)
06-17-2017, 08:42 PM
|
Replies: 6
Views: 1,239
|
Forum: Early V8 (1932-53)
06-17-2017, 08:02 PM
|
Replies: 6
Views: 1,239
speedo conversion for electronic T-5 trans
I have a '93 T-5 out of an S-10 in my '36 coupe, and it has the electronic speedo. Is there a conversion for changing this to a manual sender for the speedo cable? I also have aftermarket gauges and...
|
Forum: Early V8 (1932-53)
03-16-2017, 02:12 PM
|
Replies: 14
Views: 5,813
|
Forum: Early V8 (1932-53)
03-16-2017, 02:10 PM
|
Replies: 14
Views: 5,813
Re: 1940 coupe rubber mat
Sorry the car is at another location right now, but the new shifter location is fine. I will take a pic ASAP and post it.
|
Forum: Early V8
03-16-2017, 10:12 AM
|
Replies: 1
Views: 1,154
|
Forum: Early V8 (1932-53)
03-16-2017, 10:09 AM
|
Replies: 14
Views: 5,813
Re: 1940 coupe rubber mat
I ordered the black mat from Carpenter and it's perfect, top quality, and the price ($129) was great. Will need to be trimmed around the edges a little bit but the holes for clutch, brake, gas pedal...
|
Forum: Early V8
03-01-2017, 05:40 PM
|
Replies: 1
Views: 1,154
|
Forum: Early V8 (1932-53)
03-01-2017, 05:38 PM
|
Replies: 14
Views: 5,813
Re: 1940 coupe rubber mat
Does the rubber matting for the 40 come with any other holes pre cut other than for the pedals and column? In my 36 coupe I have put a 5 speed so the shifter is back a few inches , which left a hole...
|
Forum: Early V8 (1932-53)
12-19-2016, 04:12 PM
|
Replies: 3
Views: 1,468
|
Forum: Early V8 (1932-53)
12-19-2016, 03:18 PM
|
Replies: 3
Views: 1,468
1936 Rearend width
Does anyone know off hand what the outside to outside ( the face of the drums that the wheel bolts to) measurement is on a 36 Ford rearend? Thanks!
|
Forum: Early V8 (1932-53)
12-16-2016, 01:14 AM
|
Replies: 30
Views: 8,108
|
Forum: Early V8 (1932-53)
12-15-2016, 10:26 PM
|
Replies: 30
Views: 8,108
|
Forum: Early V8 (1932-53)
12-15-2016, 10:14 PM
|
Replies: 30
Views: 8,108
Re: '36 wheel size with drop axle
I don't think you can get a 46" axle with the same perch pin measurement as a 36 wishbone. Magnum sells a 47" which is what I'm thinking of getting for my 36 coupe.
|