Forum: Model A (1928-31)
04-14-2024, 03:30 PM
|
Replies: 12
Views: 502
Re: Recommended Turning Signal Switch
Hi,
thanks at all; extraordinary to Blockhead for the good tip advice. I didn't know Bert's shop. I have already ordered this switch there immediately.
|
Forum: Model A (1928-31)
04-14-2024, 01:10 PM
|
Replies: 12
Views: 502
Recommended Turning Signal Switch
Hello buddies,
I have a recurring problem with the universal turn signal switch. It is the cheapest "Chinese quality", the plastic housing warps and the cables quickly become stiff and the...
|
Forum: Model A (1928-31)
11-27-2023, 06:56 AM
|
Replies: 33
Views: 2,231
Re: 12 conversion
Hello, [your first name could be written here],
The tired turning of the starter motor has nothing to do with the fact that it only gets 6 volts.
You already have a start relay; check...
|
Forum: Model A (1928-31)
11-17-2023, 04:02 PM
|
Replies: 13
Views: 1,337
|
Forum: Model A (1928-31)
10-31-2023, 04:02 PM
|
Replies: 8
Views: 1,213
|
Forum: Model A (1928-31)
10-27-2023, 04:25 PM
|
Replies: 14
Views: 1,491
|
Forum: Model A (1928-31)
10-22-2023, 10:01 AM
|
Replies: 46
Views: 4,311
Re: Fuel Filter issue
8EL,
thank you very much for the detailed explanation. This is therefore not a type of fuel. And the above rejection is a political decision, I think.
|
Forum: Model A (1928-31)
10-22-2023, 06:11 AM
|
Replies: 46
Views: 4,311
|
Forum: Model A (1928-31)
09-30-2023, 03:12 PM
|
Replies: 5
Views: 658
Re: Spark Plug Gap
Good evening Bob,
Your assumption is correct.
Instead of a smaller electrode gap, which reduces the spark distance and therefore unfortunately also the amount of gas molecules that cause...
|
Forum: Model A (1928-31)
09-27-2023, 03:44 PM
|
Replies: 6
Views: 940
Re: Ford dealer emblem
Yes, I really like something like that too!
I've been looking for a very old Ford workshop emblem for a long time.
It's not interesting on Ebay. Because the freight there costs around $27 and...
|
Forum: Model A (1928-31)
09-14-2023, 04:28 PM
|
Replies: 24
Views: 2,363
Re: maximum rpm, personal choice...
A measure of the maximum engine RPM is the average piston speed. This is used for engine designs from the 1960s at 18 m/sec. specified.
Our gray cast iron heavy A engine with uncertain mass...
|
Forum: Model A (1928-31)
09-13-2023, 03:29 PM
|
Replies: 16
Views: 1,257
|
Forum: Model A (1928-31)
09-11-2023, 05:25 PM
|
Replies: 16
Views: 1,257
|
Forum: Model A (1928-31)
09-10-2023, 02:29 PM
|
Replies: 16
Views: 1,257
|
Forum: Model A (1928-31)
09-09-2023, 05:11 PM
|
Replies: 16
Views: 1,257
Sparton Horn is falling asleep more and more
Hello Walton-Fans!
I have an original Sparton horn on my 'Little Green Roadster".
The engine is causing more and more problems because it cannot reach high speeds.
I turned off the...
|
Forum: Model A (1928-31)
06-27-2023, 05:16 PM
|
Replies: 7
Views: 1,053
|
Forum: Model A (1928-31)
06-15-2023, 04:43 AM
|
Replies: 50
Views: 6,198
Re: Thermostat
Wello,
It has been my experience that glycol based antifreeze will attack the two component adhesive.
|
Forum: Model A (1928-31)
06-03-2023, 05:20 PM
|
Replies: 12
Views: 1,353
Re: Head Light Problem
Hi Bill,
I turned a considerably smaller pulley for the alternator. (Oak wood with steel disc insert.)
So I already have plenty battery charging current at idle speed.
|
Forum: Model A (1928-31)
05-27-2023, 02:11 PM
|
Replies: 13
Views: 1,688
Re: Nu Rex Timing Advance
N'Abend Bruce,
I drive with this automatic ignition since one year. Works excellent by itself without any touch up. I would buy the NuRex ignition part again.
|
Forum: Model A (1928-31)
05-21-2023, 04:18 PM
|
Replies: 125
Views: 22,914
Re: MMO in the Gas
The addition of MMO has many implications.
The highly distilled white oil used as the basis ensures passivation of the surfaces and also a certain amount of lubrication in the entire area...
|
Forum: Model A (1928-31)
05-16-2023, 04:42 AM
|
Replies: 27
Views: 4,144
Re: Source for red fan belt
Whoever not only drives his model, but also repairs and maintains it himself, should be able to create this fine color work himself.
I just think so... -
I have a general accessories...
|
Forum: Model A (1928-31)
05-10-2023, 04:06 PM
|
Replies: 10
Views: 1,625
Re: Tire valve accessories
The grooves of the four gripping arms are concentric.
The lid is plugged in.
When I pull on the upper sleeve, the grippers spread. If I push in, they grip tight.
There are no other...
|
Forum: Model A (1928-31)
05-10-2023, 04:50 AM
|
Replies: 7
Views: 1,211
|
Forum: Model A (1928-31)
05-09-2023, 04:59 PM
|
Replies: 27
Views: 5,091
|
Forum: Model A (1928-31)
05-09-2023, 03:06 PM
|
Replies: 10
Views: 1,625
Re: Tire valve accessories
Mike,
thank you for your hint.
I don't think this is a workshop tool. It's built too fragile for that and doesn't have a good grip. The top cap is detachable.
...
|