Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: Mart
Forum: Early V8 (1932-53) Today, 07:51 AM
Replies: 3
Views: 122
Posted By Mart
Re: 1936 ford hub cap

Never done it myself but a recent post described carefully drilling a hole through the steel hubcap, but not through the stainless. Then a blast of compressed air will blow the stainless part off.
...
Forum: Early V8 (1932-53) Today, 03:17 AM
Replies: 9
Views: 274
Posted By Mart
Re: Holley 94 accelerator pump helper spring

I've had a few 94s and never found a spring under the accelerator pump plunger.

Mart.
Forum: Early V8 (1932-53) Today, 03:01 AM
Replies: 7
Views: 331
Posted By Mart
Re: The Unofficial Vender List

Would it be worth adding peoples Fordbarn user name if they are active members? I'm thinking of Fred and Michael, for example.

Mart.
Forum: Early V8 (1932-53) Today, 02:59 AM
Replies: 55
Views: 2,812
Posted By Mart
Re: Warning about c&g

Someone mentioned Joe's Antique yesterday, I downloaded the catalog and in there there were specific notes re the tanks and adaptors.

To be honest sometimes we don't realise how lucky we are. If...
Forum: Early V8 (1932-53) Today, 02:50 AM
Replies: 9
Views: 422
Posted By Mart
Re: need your help

Moonraker, just out of interest, what can you tell us of the history of your car, and how it came to be in the former Soviet Union. I'd be guessing but they must be pretty rare over there, or are...
Forum: Early V8 (1932-53) Yesterday, 03:32 PM
Replies: 4
Views: 192
Posted By Mart
Re: 1948 Super Deluxe brakes mysteries solved

Well done and thanks for sharing your observations.

Mart.
Forum: Early V8 (1932-53) Yesterday, 08:17 AM
Replies: 9
Views: 242
Posted By Mart
Re: T170 trans with stock 1932 ford K member ??

I researched this, and the only way I could find to fit an overdrive trans into a 32 K member is to use a Volvo 4 spd + od box. I mocked it up. The overdrive would have to be assembled onto the box...
Forum: Early V8 (1932-53) 09-14-2019, 05:57 PM
Replies: 16
Views: 463
Posted By Mart
Re: 37 engine in 34 truck

Lower pump bolt. Good quality six sided 9/16" socket, or a 14mm knocked on if a bit undersize.
Forum: Early V8 (1932-53) 09-13-2019, 07:10 AM
Replies: 9
Views: 422
Posted By Mart
Re: need your help

If the chassis number is in this range:
18-4,661,001 to 18-5,210,700 (From Mac Van Pelts site)

Then your car is a Ford 85HP V8 and the numbers fall in the 1939 range.

The only thing not...
Forum: Early V8 (1932-53) 09-13-2019, 07:00 AM
Replies: 14
Views: 313
Posted By Mart
Re: Turn Signal Switch with Relays

As the flasher relay needs two bulbs to flash at the correct rate, I'd be inclined to wire it as normal and then see if the circuit will also pull in a relay and flash at the correct rate. If it...
Forum: Early V8 (1932-53) 09-11-2019, 11:53 AM
Replies: 6
Views: 272
Posted By Mart
Re: Sudden Drop in Gas Mileage

Could be one of the many reasons a carb runs rich. I'm only familiar with the 94 carbs. If you have a 94 you could check for:
Punctured float.
On seating needle valve.
Ruptured power valve....
Forum: Early V8 (1932-53) 09-10-2019, 04:16 AM
Replies: 1
Views: 188
Posted By Mart
Re: French flathead camshaft

It is a truck application so it might be reasonable to assume it is a grind that favours the bottom end. Don't have any numbers though, so this is an assumption. The French motors have restricted...
Forum: Early V8 (1932-53) 09-08-2019, 05:32 PM
Replies: 24
Views: 856
Posted By Mart
Re: Intermittent sticking valve

^^ Ok if you have exposed plug connectors. If later type, fully covered plug caps, you wouldn't be able to do this.

If you do this, it is a good idea to touch the screwdriver to ground on the head...
Forum: Early V8 (1932-53) 09-06-2019, 04:15 PM
Replies: 8
Views: 264
Posted By Mart
Re: front brakes

Repro drums are available.

You could fit some of the lincoln types that are available.

You could go F100.

The last two would be complete brake swap outs, not just a drum.

What are you...
Forum: Early V8 (1932-53) 09-06-2019, 12:39 PM
Replies: 18
Views: 570
Posted By Mart
Re: Ford engine factory break in process

I'm sure I've read about this before, but also remember it from my apprenticeship days. The motors are turned over by an electric motor, this beds everything in, and when the amperage falls below a...
Forum: Early V8 (1932-53) 09-06-2019, 11:48 AM
Replies: 17
Views: 641
Posted By Mart
Re: Tie Rod End Removal

Forget pickle forks. Sometimes you want to remove the joint and use it again without having the seals all buggered up.

Get one with a screw that pushes the joint out. There was a previous thread...
Forum: Early V8 (1932-53) 09-06-2019, 09:57 AM
Replies: 8
Views: 268
Posted By Mart
Re: 48-6044 Rod, engine radius purpose.

^^ The other reason is the redesigned rear mount. It affords more fore/aft location than the previous designs. The new rear mount, in conjunction with the improved clutch linkage was deemed to have...
Forum: Early V8 (1932-53) 09-06-2019, 08:48 AM
Replies: 13
Views: 515
Posted By Mart
Re: split pins usage

"It's like an ice pick that got slammed in a door jamb."

That's a great description right there.

Mart.
Forum: Early V8 (1932-53) 09-06-2019, 04:43 AM
Replies: 18
Views: 678
Posted By Mart
Re: bleeding brakes

Bleed screws are always loose. There should be no point in the bleeding process where you are sucking on the cylinder.

You should always close the bleeder before letting the pedal come up again....
Forum: Early V8 (1932-53) 09-05-2019, 01:53 PM
Replies: 15
Views: 418
Posted By Mart
Re: PU Frame Identification

Cool, Lon, glad you were able to locate it.

Mart.
Forum: Early V8 (1932-53) 09-05-2019, 04:55 AM
Replies: 24
Views: 621
Posted By Mart
Re: 32 rear trans support/torque tube cap bolts

Without calipers or a mic, just find the ones that a 5/8 wrench or socket fit on.
Forum: Early V8 (1932-53) 09-05-2019, 03:09 AM
Replies: 15
Views: 418
Posted By Mart
Re: PU Frame Identification

There are a number of things different between a 36 and a 39 frame. the trans mount is different. The area around the pedals is different. No much, but different. Is there anything about your truck...
Forum: Early V8 (1932-53) 09-04-2019, 03:10 PM
Replies: 12
Views: 509
Posted By Mart
Re: 34 Roadster pick up question

Just judging by the front suspension pics, nothing is original Ford. The late owner had a lot of very nice cars (Street Rods) built by top builders. Some of it might be original, but a hell of a lot...
Forum: Early V8 (1932-53) 09-04-2019, 06:48 AM
Replies: 9
Views: 538
Posted By Mart
Re: How to Install Piston Rings in a Relieved Block

I just use a normal compressor. Mine is thin enough to go down the bore enough in that area. Just take extra care and watch that area like a hawk.

Mart.
Forum: Early V8 (1932-53) 09-04-2019, 02:09 AM
Replies: 33
Views: 993
Posted By Mart
Re: Water pump replace

Good work Clem, on both the pump and the show.

Mart.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:29 PM.