Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: TJ
Forum: Early V8 (1932-53) Yesterday, 07:55 PM
Replies: 18
Views: 705
Posted By TJ
Unhappy Re: 32 Ford door lock cylinder

Usually if you look in the door jamb in the area where the lock enters the door you will spot a small hole in the jamb. In that hole you will spot a set screw. That screw holds the lock assembly in...
Forum: Early V8 (1932-53) Yesterday, 06:59 PM
Replies: 2
Views: 112
Posted By TJ
Re: seat pivot cover

leazer48, I left an answer for you on the V-8 Club website along with a couple of other people who posted.
Forum: Early V8 (1932-53) Yesterday, 06:57 PM
Replies: 20
Views: 458
Posted By TJ
Forum: Early V8 (1932-53) Yesterday, 06:50 PM
Replies: 11
Views: 210
Posted By TJ
Re: Wheels (rims?) For my 1952 Mercury

Wheelsmith is another good company for wheels. I would definitely stay clear of U.S.Wheel Co.
Forum: Early V8 (1932-53) Yesterday, 04:06 PM
Replies: 7
Views: 276
Posted By TJ
Re: 1935 Hydrostatic Sending Unit

John, do you have a stock Ford electric fuel gauge? If so let me know. The repo sending units work, but are not that accurate. I may have an original sender that will work for you if you are using a...
Forum: Early V8 (1932-53) Yesterday, 02:46 PM
Replies: 11
Views: 210
Posted By TJ
Re: Wheels (rims?) For my 1952 Mercury

If you call Wheel Vintiques which is also owned by Coker they can do special backspacing for you at additional cost.
Forum: Early V8 (1932-53) Yesterday, 02:44 PM
Replies: 11
Views: 210
Posted By TJ
Forum: Early V8 (1932-53) Yesterday, 12:49 PM
Replies: 14
Views: 720
Posted By TJ
Re: 1934 three window coupe

So reserve was $60,00 and the guy turned down $57,100. I suspect the $57,100 was from a straw bidder.
Forum: Early V8 (1932-53) 01-17-2021, 08:12 PM
Replies: 14
Views: 1,441
Posted By TJ
Re: 1934 sedan. Pulling out the gas tank

On some tanks the diameter of the original hole will not allow some modern senders to drop into the tank.
Forum: Early V8 (1932-53) 01-17-2021, 08:08 PM
Replies: 14
Views: 720
Posted By TJ
Re: 1934 three window coupe

In today's market $57,100 was a good price and they should have taken it. If they run it again it will be less the next time.
Forum: Early V8 (1932-53) 01-17-2021, 10:42 AM
Replies: 8
Views: 338
Posted By TJ
Re: V-8 Times

I still don't have mine either here in Nor Calif. Just for info the the box of extra copies has also not arrived to those that handle the V-8 technical Books either.
Forum: Early V8 (1932-53) 01-16-2021, 07:46 PM
Replies: 35
Views: 759
Posted By TJ
Re: Correct replacement for Fram C181-A?

Different manufacturers sometimes use different size cartridge filters.
Forum: Early V8 (1932-53) 01-16-2021, 12:04 PM
Replies: 14
Views: 1,441
Posted By TJ
Re: 1934 sedan. Pulling out the gas tank

If you are pulling out the original tank to clean it and install a non original fuel sender why not buy a new tank that would be set up for the later sender? I seriously doubt that a modern sender...
Forum: Early V8 (1932-53) 01-16-2021, 11:56 AM
Replies: 6
Views: 361
Posted By TJ
Re: 1940 Trunk Layout

Trying to drill through welded up holes can be a serious challenge.
Forum: Early V8 (1932-53) 01-15-2021, 03:02 PM
Replies: 21
Views: 979
Posted By TJ
Re: The new 1940 Ford Book is now available

The V-8 Club does have a book that covers the '38-'39 cars. You can purchase it on the V-8 Club website. www.earlyfordv8.org.
Forum: Early V8 (1932-53) 01-15-2021, 02:57 PM
Replies: 10
Views: 992
Posted By TJ
Re: 1932 ford pickup GVWR.

See BobC's post. No need for GVW when 36 and older. Your DMV person should know that as in the vehicle code. Although I should not make assumptions on what Cal DMV knows or should know.
Forum: Early V8 (1932-53) 01-14-2021, 03:57 PM
Replies: 6
Views: 276
Posted By TJ
Re: Mid 50s F-100 parts

I've bought stuff from them and had good service.
Forum: Early V8 (1932-53) 01-14-2021, 03:26 PM
Replies: 21
Views: 979
Posted By TJ
Re: The new 1940 Ford Book is now available

Just got mine today and have briefly skimmed through it. Lots of great information for '40 lovers. Kube did a great job.
Forum: Early V8 (1932-53) 01-14-2021, 03:24 PM
Replies: 12
Views: 638
Posted By TJ
Re: which comes first...the windshield or the rubber seal

I think if you had titled your post with the words "1932 Cabriolet windshield seal" he probably would have noticed it right away.
Forum: Early V8 (1932-53) 01-14-2021, 11:10 AM
Replies: 12
Views: 638
Posted By TJ
Re: which comes first...the windshield or the rubber seal

The cabriolet takes a special seal and as I recall it installs in four pieces. I would put the frame in the car and have it loose and then tuck the seal between the frame and the body. As I recall...
Forum: Early V8 (1932-53) 01-13-2021, 09:04 PM
Replies: 12
Views: 1,199
Posted By TJ
Re: Grand Cherokee rear to 1935

With the leaf springs you may have to move the axle pads. With coil overs I have found that they are difficult to find the correct spring rates to make the car ride correctly whether it is loaded...
Forum: Early V8 (1932-53) 01-13-2021, 08:51 PM
Replies: 7
Views: 455
Posted By TJ
Re: 40 front seat-50k Rouge tudor like new!!

Dale, not found like that very often.
Forum: Early V8 (1932-53) 01-13-2021, 12:40 PM
Replies: 17
Views: 535
Posted By TJ
Re: Speedometer for 36 to S 10 tail shaft transmission?

The stock speedo cable should work if long enough. I have used the stock cable with a turbo 350 automatic and it worked just fine. The end that goes on the stock "turtle" should also go right on the...
Forum: Early V8 01-13-2021, 11:26 AM
Replies: 1
Views: 206
Posted By TJ
Forum: Early V8 (1932-53) 01-13-2021, 11:18 AM
Replies: 33
Views: 1,503
Posted By TJ
Re: who best to drop 1932 ford axle

I used Nostalgia Sid for '40 axle and he did a great job.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:15 AM.