The Ford Barn
FordBarn.com
The Forum
Swap
About
Register
Calendar
Members List
Search
Today's Posts
Mark Forums Read
FAQ
The Ford Barn
>
Search Forums
Search Results
User Name
Remember Me?
Password
Sponsored Links (Register now to hide all advertisements)
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
Railcarmover
Forum:
Model A (1928-31)
01-14-2018, 05:28 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Nah,just dont do any clutch dumps at half throttle,Imagine that flywheel can raise hell with the grey iron bellhousing...be like somebody set off a claymore at your crotch..
Forum:
Model A (1928-31)
01-14-2018, 12:50 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
^^^ Im with John on the radius,the shear factor is too high^^^^
Forum:
Model A (1928-31)
01-13-2018, 09:20 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
I run a hard washer and rtv,blue loctite and a grade 8 nut instead of the cotter and castellated nut on the mains..
Id take detailed picture and get that engine running before I off it..if it were...
Forum:
Model A (1928-31)
01-13-2018, 09:56 AM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Those rear main journal radius's are short but that was the rear thrust as Tom said.Pull those other caps. From what Ive seen so far you should clean and build,why buy or even identify the...
Forum:
Model A (1928-31)
01-12-2018, 08:55 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Did you pull the main caps?..post up a picture of the bearing shell where the part number is.
Forum:
Model A (1928-31)
01-11-2018, 08:18 AM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Well that should fetch a fair price,and a satisfied customer. The glyptol is a nice touch.
Forum:
Model A (1928-31)
01-10-2018, 09:23 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Its all good,the dipper rain shower has value. I would think if the dipper port was drilled into the insert it wouldn't hurt,hell it might help.In operation the dipper never starves,it would provide...
Forum:
Model A (1928-31)
01-09-2018, 11:03 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Im going to say that dippers are the fastest way to get oil to the rod bearing,then they lose the 'fight' when pressure builds..if that adds up its a good idea then,figure the oil under pressure...
Forum:
Model A (1928-31)
01-09-2018, 08:44 PM
Replies:
32
bearing insert identification help...
Views:
4,304
Posted By
Railcarmover
Re: bearing insert identification help...
Federal Mogul 2531 crosses to a CAT 8N8226 off highway truck rod bearing...what are you working on ?
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General Discussion
Model T (1909-1927)
Model A (1928-31)
Early V8 (1932-53)
Late V8 (1954+)
Hot Rods & Customs
The Swap Meet
For Sale
Model-T
Model-A
Early V8
Late V8
The Jalopy Auction House
To The Editors
Questions & Suggestions
The Test Forum
The Archives
Model-T
Model-A
Early V8
Late V8
Sponsored Links (Register now to hide all advertisements)
All times are GMT -5. The time now is
04:07 PM
.