Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Jacksonlll
Forum: Model A (1928-31) 10-17-2020, 06:26 AM
Replies: 19
Views: 805
Posted By Jacksonlll
Re: question

Sure sounds like a fun thing to do. Why not ask? Good luck.
Forum: Model A (1928-31) 10-13-2020, 05:35 AM
Replies: 30
Views: 1,459
Posted By Jacksonlll
Re: Model A only runs 40 miles

Check to make sure the ferrule is at the very end of the gas line going into the carb. If it hits the screen, it can restrict flow. It should not matter on a tilliston, but easy to check.
Forum: Model A (1928-31) 10-10-2020, 07:00 AM
Replies: 8
Views: 787
Posted By Jacksonlll
Re: ModelA Times

If you do use the electronic system, only you can fix it and supply the parts when on tour with other A’s. They can’t help you in most cases.
Forum: Model A (1928-31) 10-07-2020, 07:27 PM
Replies: 12
Views: 651
Posted By Jacksonlll
Re: horn blows while driving

If everything looks good, it might be that the tip of the horn rod is grounding against some metal. I have fixed a few using a large soda straw, plastic. Cut a small piece and slip it over the end...
Forum: Model A (1928-31) 10-06-2020, 12:38 PM
Replies: 16
Views: 1,043
Posted By Jacksonlll
Re: Bell housing

He does have float a mtr's but they look good. I'm thinking that the forks may be put it backwards. Never tried it.
We do intend to measure a lot of areas and compare it to another A
Forum: Model A (1928-31) 10-06-2020, 06:10 AM
Replies: 16
Views: 1,043
Posted By Jacksonlll
Re: Bell housing

UPDATE: He put it all together and the only issues that he can live with are: Pedals seem shifted a bit inboard and there is not enough pedal shaft length to space them out. Gear shift lever hits...
Forum: Model A (1928-31) 10-04-2020, 03:30 PM
Replies: 16
Views: 1,043
Posted By Jacksonlll
Bell housing

Need some help by you experts. A friend had his engine and trans rebuilt. The builder found some damage to the bell housing so he put another one on it. My friend puts his engine in and the pedals...
Forum: Model A (1928-31) 10-04-2020, 06:18 AM
Replies: 8
Views: 398
Posted By Jacksonlll
Re: Camera Recommendations for Recording Model A Suspension

A go pro would do a great job and there would be no sound, but they are very expensive and it would have to be mounted so it could not fall off. When I did this, I used an old magnetic base from an...
Forum: Model A (1928-31) 10-03-2020, 05:43 AM
Replies: 11
Views: 564
Posted By Jacksonlll
Re: Radius Ball Service

Her is a video I did with a camer under the car. It's rough, but it shows a little of what goes on under there. ...
Forum: Model A (1928-31) 10-02-2020, 10:14 AM
Replies: 12
Views: 276
Posted By Jacksonlll
Re: Slight high speed miss

Check ferrule at end of fuel line. Must right at end of tube. Tube hits screen and restricts flow.
Forum: Model A (1928-31) 09-30-2020, 05:57 AM
Replies: 5
Views: 477
Posted By Jacksonlll
Re: Tow in Alignment

Why go it alone? Isn't there a Model A club near you? They would have one. Good luck. Toe is important.
Forum: Model A (1928-31) 09-29-2020, 01:51 PM
Replies: 9
Views: 343
Posted By Jacksonlll
Re: low & no spark on #3 cyl

Check your compression to rule that out.
Forum: Model A (1928-31) 09-28-2020, 08:39 PM
Replies: 32
Views: 1,332
Posted By Jacksonlll
Re: Radial sway

Try 50 psi and see if you can tell a difference.
Forum: Model A (1928-31) 09-26-2020, 07:43 PM
Replies: 32
Views: 1,332
Posted By Jacksonlll
Re: Radial sway

I had a terrible yaw problem on my heavy town sedan. It was unsafe. I put a friends firestones on the rear and that fixed it. I then bought 4 Firestone’s and that fixed it.
A Tudor is a light car...
Forum: Model A (1928-31) 09-24-2020, 05:26 AM
Replies: 24
Views: 1,150
Posted By Jacksonlll
Re: Hot water heater will not fit

Just make sure you don't lock yourself into a big job when you have to take the floor boards out. You have to be able to work on the car out on the road. Good luck.
Forum: Model A (1928-31) 09-23-2020, 07:44 PM
Replies: 24
Views: 1,150
Posted By Jacksonlll
Re: Hot water heater will not fit

A manifold heater does a great job in southern Mi.
Forum: Model A (1928-31) 09-21-2020, 07:26 PM
Replies: 13
Views: 720
Posted By Jacksonlll
Re: Timing gear

I like fiber. Quiet.
Forum: Model A (1928-31) 09-18-2020, 01:00 PM
Replies: 18
Views: 789
Posted By Jacksonlll
Re: Starter failure

Connect a jumper cable between the neg batt post and the starter. Assuming you are pos ground. Try it. You may have high resistance in the neg batt cable. Easy to try.
Forum: Model A (1928-31) 09-14-2020, 07:17 PM
Replies: 18
Views: 778
Posted By Jacksonlll
Re: Radius ball cap

Check that toe in.
Forum: Model A (1928-31) 09-14-2020, 07:15 PM
Replies: 8
Views: 404
Posted By Jacksonlll
Re: Lack of power/rpm

Make sure your fuel line is not goin too far into the carb. Ferrule should right at the end.
Forum: Model A (1928-31) 09-14-2020, 06:36 AM
Replies: 23
Views: 595
Posted By Jacksonlll
Re: Engine quit running help

When you checked the timing gear, did you see it turn?
Or, look down in the dist hole and see it the shaft is turning. If it is, your problem is all on top and should be an easy fix.
Retorque...
Forum: Model A (1928-31) 09-09-2020, 05:30 AM
Replies: 17
Views: 1,030
Posted By Jacksonlll
Re: toe in gauge

Find an A club and join it. They will have one.
Forum: Model A (1928-31) 09-08-2020, 07:10 AM
Replies: 9
Views: 520
Posted By Jacksonlll
Re: Tire Questions

If you have a heavy Townsedan, be sure to use a stiff tire like Firestone. The excessive yaw was killing me.
Forum: Model A (1928-31) 09-06-2020, 07:18 PM
Replies: 14
Views: 969
Posted By Jacksonlll
Re: Wandering

Inflate your tires to 50 psi and try it.
The other thing you can try is to put a friends tires and wheels on the rear and try it. Easy to do.
Forum: Model A (1928-31) 09-02-2020, 05:56 AM
Replies: 9
Views: 395
Posted By Jacksonlll
Re: tutorial or video to adjust a clutch ??

I assume that you realize that the A trans. does not have syncronizers.
Search youtube for How to shift a model a.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:36 PM.