Forum: Model A (1928-31)
Today, 11:01 AM
|
Replies: 6
Views: 342
Re: Vulcan 1 cylinder head
It was made in the 70's in the San Bernardino area. There was a Model A guy that owned a parts store there and he produced a few performance parts. I think his last name was James???
Most any...
|
Forum: Model A (1928-31)
Yesterday, 12:27 PM
|
Replies: 5
Views: 368
|
Forum: Model A (1928-31)
03-14-2024, 11:48 AM
|
Replies: 3
Views: 232
|
Forum: Model A (1928-31)
03-12-2024, 12:10 PM
|
Replies: 16
Views: 1,061
Re: Donovan 4 Cylinder
Vintage 4 (V4) classes are allowed any OHV or OHC conversion that you want to run, its the block that SCTA limits, to 1934 or earlier, or any block approved by the original manufacturer as a...
|
Forum: Model A (1928-31)
03-11-2024, 11:19 AM
|
Replies: 29
Views: 1,422
Re: Synchronized Transmission
I'm not sure that others have actually answered your question. For my money the early Ford V8 trans is the best way to go. The '39 is the best, but the '32-'38 work very well too. The difference...
|
Forum: Model A (1928-31)
03-08-2024, 07:32 PM
|
Replies: 16
Views: 1,061
Re: Donovan 4 Cylinder
Donovan makes a flathead but most guys use an OHV head. The Model D (Donovan's name for the banger block) is super strong, and expensive but worth it if you are going to drive it hard. They are not...
|
Forum: Model A (1928-31)
03-04-2024, 12:00 PM
|
Replies: 8
Views: 564
Re: Speedometer Cable- A Grease Pump?
When greasing the cable, don't put grease in the upper 6". That area is straight so doesn't need it. Too much grease will get into the speedo itself, and cause problems.
|
Forum: Model A (1928-31)
03-02-2024, 11:57 AM
|
Replies: 7
Views: 604
|
Forum: Model A (1928-31)
02-28-2024, 12:43 PM
|
Replies: 16
Views: 972
Re: Lion Speed Head?
I think they sold new for $650? Piranio in TX bought raw castings from Yapp and machined his own chamber into them.
|
Forum: Model A (1928-31)
02-27-2024, 12:34 PM
|
Replies: 1,400
Views: 306,007
Re: tell a Model A related story
Will do Woofa! Did I tell you that when I got a new card from my credit union, I can now use the ATM! A young friend of mine told me that I am now just like a teenager! ... I don't believe that...
|
Forum: Model A (1928-31)
02-26-2024, 01:19 PM
|
Replies: 1,400
Views: 306,007
Re: tell a Model A related story
Woofa, unlike you, I am very up to date on electronic gadgets. I have a flip phone, and I turn it on when I leave the house, well, almost every time, which is maybe once a week? I can make and...
|
Forum: Model A (1928-31)
02-25-2024, 01:09 PM
|
Replies: 12
Views: 601
Re: Which Headers
4 into 1 tube header is the most efficient but at the RPM most guys run with their A's, it makes little difference. Cast iron headers or manifold retain heat and, I've found, make your car hotter...
|
Forum: Model A (1928-31)
02-23-2024, 12:59 PM
|
Replies: 17
Views: 633
|
Forum: Model A (1928-31)
02-22-2024, 12:50 PM
|
Replies: 5
Views: 526
Re: Rear End Rebuild Advice/Help Needed
Tom is exactly right, but I don't recommend torquing the side housings without gasket or shims of some kind in place, there is danger of distorting the housings, and they will leak.
|
Forum: Model A (1928-31)
02-19-2024, 02:05 PM
|
Replies: 2
Views: 327
Re: Holley 81 v8 60 carbs
Holley carbs, in general, need smaller than stock power valves when used in multiples. The reason is when in pairs, or more, the manifold vacuum drops quicker than as a single carb, so makes the...
|
Forum: Model A (1928-31)
02-19-2024, 02:00 PM
|
Replies: 10
Views: 948
Re: Riley ?
The originals were drilled using hardwood as guides, so often were not concentric, as on my 1936 4-port.
|
Forum: Model A (1928-31)
02-18-2024, 01:23 PM
|
Replies: 11
Views: 912
Re: Not even a Ford pulling
I worked as a mechanic at a GMC dealer in the 50's. We had a customer that transported new Chrysler products. Chrysler insisted that he used a Dodge truck instead of his GMC, so ... he changed the...
|
Forum: Model A (1928-31)
02-18-2024, 01:15 PM
|
Replies: 10
Views: 948
Re: Riley ?
Riley 2-port, maybe $3500, if it is not cracked and is complete. 4-port, iron or aluminum, complete, $5,000 more or less depending on how much the buyer wants it.
|
Forum: Model A (1928-31)
02-18-2024, 01:11 PM
|
Replies: 2
Views: 438
|
Forum: Model A (1928-31)
02-14-2024, 12:28 PM
|
Replies: 5
Views: 656
Re: 31 coupe with a Rucker overhead valve
History lesson for today,
Rucker's were made when the Model A was new. They are somewhat rare now. They were similar to several OHV heads of the day, like the Cragar heads they could use stock...
|
Forum: Model A (1928-31)
02-14-2024, 12:15 PM
|
Replies: 34
Views: 6,313
|
Forum: Model A (1928-31)
02-14-2024, 11:57 AM
|
Replies: 49
Views: 3,035
|
Forum: Model A (1928-31)
02-14-2024, 11:56 AM
|
Replies: 49
Views: 3,035
|
Forum: Model A (1928-31)
02-13-2024, 01:07 PM
|
Replies: 49
Views: 3,035
|
Forum: Model A (1928-31)
02-12-2024, 12:43 PM
|
Replies: 49
Views: 3,035
|