Forum: Model A (1928-31)
Yesterday, 10:14 AM
|
Replies: 8
Views: 348
Re: Choke rod
Open the hole in the grommet with a sharp drill or a rat tail file.
|
Forum: Model A (1928-31)
03-16-2024, 12:17 PM
|
Replies: 7
Views: 602
Re: cracked main bearing
The repair thrust face available from Syner's (A-6334) is my choice. I have an engine that needs it. I plan to secure the repair thrust face with JB Weld.
|
Forum: Model A (1928-31)
03-16-2024, 12:05 PM
|
Replies: 10
Views: 520
Re: 190-A Victoria Coupe Trivia
The storage space in the bustle of the Victoria is limited and more suitable for blankets. There is more storage space under the rear seat for spare parts.
|
Forum: Model A (1928-31)
03-15-2024, 10:17 AM
|
Replies: 8
Views: 658
|
Forum: Model A (1928-31)
03-15-2024, 10:16 AM
|
Replies: 7
Views: 602
Re: cracked main bearing
The crack is likely due to the Babbitt rear thrust face not adhering to the cap when it was poured, so there is a small gap between the Babbitt and the cap. Continuous on-off pressure from the...
|
Forum: Model A (1928-31)
03-15-2024, 10:06 AM
|
Replies: 3
Views: 234
Re: Model "B" Engine Differences
I fixed the post. As Jim mentions, it should 19 Degrees. I forgot to superscript the 0 in 190. Thanks Jim for correcting my oversight.
|
Forum: Model A (1928-31)
03-15-2024, 10:00 AM
|
Replies: 14
Views: 633
|
Forum: Model A (1928-31)
03-15-2024, 09:45 AM
|
Replies: 8
Views: 566
Re: Frame numbers
A rule of thumb is that the Model "A" or "AA" engine number was stamped into the frame within 90 days of the engines foundry date. So the foundry date of April 8, 1930 likely went into a vehicle on a...
|
Forum: Model A (1928-31)
03-15-2024, 09:39 AM
|
Replies: 17
Views: 454
Re: Front fender cracking out
Test fit the fenders with their support brackets. Cracks can only occur in the metal where there is a tension stress / strain. The tension typically occurs where the fenders / support brackets are...
|
Forum: Model A (1928-31)
03-14-2024, 11:08 AM
|
Replies: 3
Views: 234
Model "B" Engine Differences
In 1932 an “Improved 4-Cylinder Engine” was introduced for cars and trucks, and it remained in vehicle production through 1934. Buyers had a choice of the Improved 4-Cylinder engine or the new V8....
|
Forum: Model A (1928-31)
03-14-2024, 09:32 AM
|
Replies: 10
Views: 520
190-A Victoria Coupe Trivia
A total of 43,250 Model "A"Victoria Coupes were made including domestic cars, foreign cars and knock-down bodies. By far, the largest quantity of Victoria Coupes were assembled in the Edgewater, New...
|
Forum: Model A (1928-31)
03-13-2024, 09:38 AM
|
Replies: 11
Views: 661
Re: Engine paint
I have seen original NOS Model "A" parts in a light green to a dark green, so ditto Charlie Stevens comment in Post #2. In my opinion, leftover enamels were mixed by Ford. I also notice that Ford...
|
Forum: Model A (1928-31)
03-12-2024, 07:22 AM
|
Replies: 18
Views: 760
|
Forum: Model A (1928-31)
03-11-2024, 09:25 AM
|
Replies: 6
Views: 349
Re: 1931 Slant Windshield Fordor Firewall
The slant windshield first appeared on the 190A Victoria late in 1930. The Victoria is the pioneer Ford for many 1931 features including the 1931 style radiator shell and recessed doors.
|
Forum: Model A (1928-31)
03-10-2024, 11:14 AM
|
Replies: 10
Views: 447
|
Forum: Model A (1928-31)
03-07-2024, 01:22 PM
|
Replies: 28
Views: 5,099
Re: Main bearing bolts
Torque of a structural joint should be to 75% of the bolt / stud yield strength. This reduces the alternating stress range (varying tension) induced by the reciprocating parts in the engine. Reducing...
|
Forum: Model A (1928-31)
03-07-2024, 01:04 PM
|
Replies: 9
Views: 370
Re: Replace rear motor mounts
I have changed the rear engine mounts in my A's a few times, and it was not necessary to spread the frame.
I did a comparison between an original set of Engine Rear Support Cushions A-5092 Inner...
|
Forum: Model A (1928-31)
03-06-2024, 12:39 PM
|
Replies: 18
Views: 832
Re: counterbalanced crank welds
The strength of the crankshaft material and its fatigue life are effected by welding, especially if the crankshaft is not heat treated to relieve thermal stresses after welding. Use the crankshaft as...
|
Forum: Model A (1928-31)
03-02-2024, 11:27 AM
|
Replies: 22
Views: 920
|
Forum: Model A (1928-31)
03-01-2024, 10:42 AM
|
Replies: 10
Views: 792
Re: Paint scheme
Hi McGarrett! I had a minor accident that knocked the hubcap off of the wheel. All is fixed now with a brand new hubcap.
|
Forum: Model A (1928-31)
03-01-2024, 10:23 AM
|
Replies: 22
Views: 1,158
Re: Wheel stud replacement
The studs are riveted into the drum and have a shoulder that prevents hammering / pushing them out. There is a tool to cutaway the shoulder.
|
Forum: Model A (1928-31)
02-29-2024, 12:32 PM
|
Replies: 16
Views: 998
Re: Ford car Ford gas
The Ford Motor Company produced an alternative fuel sold under the name Benzol from 1932 to 1942. It consisted of three parts gasoline and one part light oil, a by-product from the coal used in...
|
Forum: Model A (1928-31)
02-29-2024, 11:55 AM
|
Replies: 16
Views: 1,044
|
Forum: Model A (1928-31)
02-29-2024, 11:51 AM
|
Replies: 10
Views: 792
Re: Paint scheme
The owner who selected the paint scheme you saw likely shared my opinion. I did it my way, not the Ford way. In my opinion, Model A color schemes are way too dark and boring.
|
Forum: Model A (1928-31)
02-29-2024, 11:43 AM
|
Replies: 4
Views: 350
|