Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: MABidwell
Forum: Early V8 (1932-53) 09-17-2021, 11:25 AM
Replies: 10
Views: 345
Posted By MABidwell
Re: Rear Engine Mount?

So, the mystery part was part of the old mount and it just separated from the main frame over time?
Forum: Early V8 (1932-53) 09-17-2021, 10:01 AM
Replies: 10
Views: 345
Posted By MABidwell
Re: Rear Engine Mount?

Thanks for responding. I probably should have included a bit more information.

I do have part #6068 (new from D. Carpenter - the rubber on the original was shot).

The piece that was bolted to...
Forum: Early V8 (1932-53) 09-16-2021, 02:11 PM
Replies: 10
Views: 345
Posted By MABidwell
Rear Engine Mount?

1946 Super Deluxe

Iím trying to figure out if the rubber backed engine/transmission support assembly should be bolted down to the frame bracket with the pan head bolts that hold the saddle (?) to...
Forum: Early V8 (1932-53) 05-20-2021, 08:36 PM
Replies: 3
Views: 331
Posted By MABidwell
Forum: Early V8 (1932-53) 05-20-2021, 05:37 PM
Replies: 3
Views: 331
Posted By MABidwell
Radiator Support Cross Bar

Iím wondering if the bar I have is bent. I know thereís a curved section towards one end, but thereís another indent on the other end that doesnít seem right. Anybody know what to look for here? Iím...
Forum: Early V8 (1932-53) 04-05-2021, 03:20 PM
Replies: 3
Views: 367
Posted By MABidwell
Forum: Early V8 (1932-53) 04-05-2021, 01:54 PM
Replies: 3
Views: 367
Posted By MABidwell
Shackle Stud Replacement

I've been searching for KR Wilson BV-121tool to replace my shackle studs (I have NOS studs), but no luck so far. So, I'm thinking about modifying a C clamp with the guides that can be fabricated. ...
Forum: Early V8 (1932-53) 03-06-2021, 06:38 PM
Replies: 11
Views: 902
Posted By MABidwell
Re: Pinion Bearing Lubrication

Thanks, everyone for the advice on this.
Forum: Early V8 (1932-53) 03-05-2021, 10:50 AM
Replies: 11
Views: 902
Posted By MABidwell
Pinion Bearing Lubrication

Getting ready to re-assemble the pinion gear assembly and want to know if I should pack the three bearings with grease or just a little gear oil (140W) beforehand. I know the bearings will be...
Forum: Early V8 (1932-53) 08-31-2018, 09:25 AM
Replies: 7
Views: 898
Posted By MABidwell
Re: Leaf Spring Grease Fittings

Thanks everyone for the input. My hunch was that taking a cage nut with flanges and then working with them to get them into to metal wrap was the best solution. Also appreciate the advice on the...
Forum: Early V8 (1932-53) 08-30-2018, 11:49 AM
Replies: 7
Views: 898
Posted By MABidwell
Leaf Spring Grease Fittings

I'm working on a 1946 Ford Super Deluxe station wagon (woodie) that has metal wrapped leaf springs. Each spring has two zerks embedded in the wrap. The zerks are mounted in a special cage nut that...
Showing results 1 to 11 of 11

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:36 AM.