Forum: Late V8 (1954+)
11-21-2023, 11:42 AM
|
Replies: 2
Views: 647
|
Forum: Late V8 (1954+)
11-21-2023, 10:36 AM
|
Replies: 2
Views: 647
1959 Edsel 361 Lifters
Anyone know the part number for non adjustable hydraulic lifters?
Are they the same as the lifters used in adjustable rockers?
Thanks in advance
|
Forum: Model T (1909-1927)
03-25-2022, 01:26 PM
|
Replies: 2
Views: 833
|
Forum: Model T (1909-1927)
03-25-2022, 08:32 AM
|
Replies: 2
Views: 833
|
Forum: Model-T
03-24-2022, 10:47 AM
|
Replies: 0
Views: 628
|
Forum: Early V8 (1932-53)
05-04-2021, 11:57 AM
|
Replies: 7
Views: 1,382
|
Forum: Early V8 (1932-53)
05-03-2021, 02:41 PM
|
Replies: 7
Views: 1,382
49 F1 I 6 carb question
Does anyone know why someone would put 8 carb to intake gasket on ? Also should the small hole on the bottom of the carb not be block
|
Forum: Late V8
12-08-2020, 12:26 PM
|
Replies: 0
Views: 739
Help need transmission drum
Some how mine rolled off the bench hit the floor and bent the spline. It is 3.375" in height
1956 Cruise o matic medium case
anyone have one or any leads ?
Thanks in advance
|
Forum: Late V8 (1954+)
12-08-2020, 12:25 PM
|
Replies: 1
Views: 837
Help! need transmission drum.
Some how mine rolled off the bench hit the floor and bent the spline. It is 3.375" in height
1956 Cruise o matic medium case
anyone have one or any leads ?
Thanks in advance
|
Forum: Late V8 (1954+)
01-16-2020, 12:18 PM
|
Replies: 4
Views: 1,496
|
Forum: Late V8 (1954+)
01-16-2020, 09:23 AM
|
Replies: 4
Views: 1,496
Edsel transmission leak
hello,
seems like I have yet another transmission leak. The seal on the shift rod that goes into the side of the transmission is leaking.My question is do I have to replace that seal from the...
|
Forum: Model A (1928-31)
08-07-2019, 07:54 AM
|
Replies: 15
Views: 2,435
Re: 30 Model A Zenith Carb
Thanks for all the input. I really appreciate it. Stuck needle I assume from shipping.
Runs fine after tapping the carb with a small hammer.
|
Forum: Model A (1928-31)
08-06-2019, 08:56 AM
|
Replies: 15
Views: 2,435
30 Model A Zenith Carb
hello,
I bought a rebuilt card from a gentleman in Eaton Ohio. I put it on and it is hard to start and barely runs with the choke out and the throttle all the way open. It will run for about 15...
|
Forum: Early V8 (1932-53)
11-05-2018, 08:10 AM
|
Replies: 4
Views: 1,782
|
Forum: Early V8 (1932-53)
11-02-2018, 08:53 AM
|
Replies: 4
Views: 1,782
1952 Ford F6 brake question
hello all,
I recently replaced the entire brake system new lines wheels cylinders master cylinder shoes turned drums. I can get a peddle. I can pump it up and it will hold until I release and then...
|
Forum: Early V8 (1932-53)
10-01-2018, 07:05 AM
|
Replies: 6
Views: 1,391
|
Forum: Early V8 (1932-53)
09-28-2018, 01:34 PM
|
Replies: 6
Views: 1,391
|
Forum: Early V8 (1932-53)
09-27-2018, 07:06 AM
|
Replies: 6
Views: 1,391
|
Forum: Early V8 (1932-53)
09-13-2018, 01:48 PM
|
Replies: 18
Views: 3,119
|
Forum: Early V8 (1932-53)
09-13-2018, 01:47 PM
|
Replies: 18
Views: 3,119
|
Forum: Early V8 (1932-53)
09-13-2018, 07:01 AM
|
Replies: 18
Views: 3,119
|
Forum: Early V8 (1932-53)
09-12-2018, 03:18 PM
|
Replies: 18
Views: 3,119
Re: 1952 Ford COE hydrulic control question
I have another question for you fine gentlemen. I have replaced the entire brake system lines wheel cylinders master cylinder relined shoes turned drums, ( not that this has anything to do with my...
|
Forum: Early V8 (1932-53)
09-11-2018, 01:13 PM
|
Replies: 18
Views: 3,119
Re: 1952 Ford COE hydrulic control question
Here is a picture of the 2 parts I am asking about. the top 2 PC lever has to go on the pump the smaller has to go on the tranny to hold the PTO cable. It has to be simple but I just cant see have or...
|
Forum: Early V8 (1932-53)
09-11-2018, 12:10 PM
|
Replies: 18
Views: 3,119
Re: 1952 Ford COE hydrulic control question
yes I have located all the parts and have actually got under the truck engaged the unit the started the engine and lifted the bed. then shut the engine off got under the truck and lowered the bed t...
|
Forum: Early V8 (1932-53)
09-10-2018, 11:53 AM
|
Replies: 18
Views: 3,119
Re: 1952 Ford COE hydrulic control question
thanks 47 COE and rotowrench. Mine has 2 cables in the floor one activates the PTO the other the pump. I just don't have pics of how it connects to the 2. They are located between the seats
|