Forum: Model A (1928-31)
11-11-2019, 11:04 AM
|
Replies: 3
Views: 1,848
FS ignition timing
My motor is basically stock with a lion speed 4 head and headers....internals are all stock.....I installed a FSI electronic distributor (not the zipper) and been running it at that for a couple...
|
Forum: Model-A
11-07-2019, 11:36 PM
|
Replies: 0
Views: 1,007
Clings adapter
SOLD
Have complete Clings adapter for 37-39 V8 tranny to banger motor. Brand new, never used
$400.00 for everything picked up here or add shipping.
tried posting pics but this site wont do...
|
Forum: Model A (1928-31)
07-07-2018, 05:15 PM
|
Replies: 1
Views: 1,348
Door latch removal
Here’s my issue....1930 tudor...right hand door is in locked position, so I can’t rotate shaft enough to release it from latch...no key...how do I remove this door latch so I can replace. I can get...
|
Forum: Model A (1928-31)
04-10-2018, 10:32 PM
|
Replies: 12
Views: 2,644
Banger PVC
Has anyone installed a PVC valve in a banger engine. If so, any tips. Thanks Ron
|
Forum: Early V8 (1932-53)
02-05-2017, 01:20 PM
|
Replies: 6
Views: 1,564
Re: starter question
Thanks Mac....shoulda called you in the first place...your always great to speak with...hope the weather is treating you fine back there Ron
|
Forum: Early V8 (1932-53)
02-04-2017, 09:20 PM
|
Replies: 6
Views: 1,564
Re: starter question
yes it is like this pic. Got it from Macs and it says for flathead V8....will this not work? if it will, what do I do with the strap?
|
Forum: Early V8 (1932-53)
02-03-2017, 11:10 PM
|
Replies: 6
Views: 1,564
starter question
picked up a new starter for my 37 21 stud engine. What is the brass/copper strap for that is attached to the stud.
|
Forum: Questions & Suggestions
02-01-2017, 11:06 PM
|
Replies: 2
Views: 1,518
starter question
just picked up a new starter for my 21 stud 37 engine. What is the brass/copper strap for that is attached. the original starter did not have one.
|
Forum: Early V8
09-10-2016, 06:54 PM
|
Replies: 0
Views: 800
9" clutch assembly
Have brand new, never used 9" pressure plate, disc and alignment tool. bought 9" when I needed 10"
$120.00 shipped thanks Ron
|
Forum: Early V8 (1932-53)
08-04-2016, 01:29 PM
|
Replies: 10
Views: 1,683
Re: 37 rod bearings
so do they have to float both over the crank journal AND inside the rod at the same time or just either one freely.
|
Forum: Early V8 (1932-53)
08-04-2016, 12:43 PM
|
Replies: 10
Views: 1,683
|
Forum: Early V8 (1932-53)
08-03-2016, 10:06 PM
|
Replies: 10
Views: 1,683
37 rod bearings
the new rod bearings for my 37 are flanged. Do these still need to be fitted using the hammer method?
|
Forum: Early V8 (1932-53)
07-25-2016, 07:28 PM
|
Replies: 7
Views: 1,617
Re: Main bearing markings
this is the rear main the other two main bearings are not marked but they mic exactly the same thickness as the rear main. I think the mains marked A2 is std, G2 is 0.010 and U2 is 0.020 as best I...
|
Forum: Early V8 (1932-53)
07-25-2016, 03:59 PM
|
Replies: 7
Views: 1,617
Main bearing markings
Looking to determine if 1937 21 stud engine crank is ground undersize. Looked in oil groove of main bearing and nothing but on the back of the shell it says....Ford (script) USA-T G2....do these...
|
Forum: Early V8 (1932-53)
07-24-2016, 03:31 PM
|
Replies: 3
Views: 899
Re: 1937 21 stud crank thrust
ive got about .035 endplay and should be, from what i can find .01 to .015. . I miced the flanges on the cap half of the bearing shell and have.069 and .064 on flywheel side.
so i think i need to...
|
Forum: Early V8 (1932-53)
07-24-2016, 02:03 PM
|
Replies: 3
Views: 899
1937 21 stud crank thrust
can anyone tell me that the main bearing thrust dimensions are on a standard main bearing, im looking for the thickness of the thrust flange on the bearing. Ive got a little excess clearance but the...
|
Forum: Early V8 (1932-53)
07-23-2016, 08:02 PM
|
Replies: 1
Views: 1,221
intake manifold
are intake manifolds interchangeable between 21 and 24 stud motors. thanks
|
Forum: Model A (1928-31)
07-22-2016, 05:04 PM
|
Replies: 6
Views: 1,855
Door lock issue
My 30 Tudor has the passenger door lock in the locked position with no key. Ive tried removing all the screws and rotating as far as I can but the shaft is just short of rotating enough to remove it...
|
Forum: Early V8 (1932-53)
07-11-2016, 06:45 PM
|
Replies: 3
Views: 1,290
transmission swap
found a 37 tranny to go with my 37 21 stud for my 30 Tudor. The 37 trans is complete less tail section and u joint. Can i use the tail section off my 30 trans on this 37 trans. if not what do I need...
|
Forum: Early V8 (1932-53)
07-04-2016, 08:07 PM
|
Replies: 9
Views: 1,878
Re: 37 21 stud question
Got the short block going back together and I plan on using an electric fuel pump and want to eliminate the mechanical fuel pump but there is a scoop mounted on top that I assume is to help vacate...
|
Forum: Early V8 (1932-53)
06-30-2016, 07:18 PM
|
Replies: 9
Views: 1,878
Re: 37 21 stud question
great thanks for the quick reply...this motor is getting all new valvetrain and piston rering so hpefully not a bunch of crankcase pressure
|
Forum: Early V8 (1932-53)
06-30-2016, 06:40 PM
|
Replies: 9
Views: 1,878
37 21 stud question
I see this motor has no rear main seal but has a slinger instead. Do these motors with slingers only leak and if so how bad, or is there a way to install a rope seal. Little confused here and being a...
|
Forum: Early V8 (1932-53)
06-28-2016, 11:53 PM
|
Replies: 12
Views: 2,257
21 stud piston rings
have 37 21 stud motor with 3 ring aluminum domed pistons 30 over. looking for rings for these. everything I can find shows second ring to have expansion ring underneath, but my pistons have standard...
|
Forum: Questions & Suggestions
06-28-2016, 08:18 PM
|
Replies: 1
Views: 1,129
piston ring question
have 37 21 stud engine that i need correct piston rings for. this motor has aluminum 3 ring pistons that has two upper rings , compression and wiper and an lower 3 piece oil ring with expander. all...
|
Forum: Early V8
06-02-2016, 12:01 AM
|
Replies: 0
Views: 844
39 tranny wanted
looking for a 39 tranny in decent shape for my 30 Tudor.
Ron, Fresno, Ca
|