Forum: Model A (1928-31)
06-09-2019, 12:38 PM
|
Replies: 7
Views: 1,924
Re: Bolts rear motor mount to clutch housing
I finally got top bots out with a thinwall socket, a breaker bar extend with a steel pipe. For the bottom bolt I had to cut the mounts in half with a sawzall and carbide blade....took a monster...
|
Forum: Model A (1928-31)
06-02-2019, 03:32 PM
|
Replies: 7
Views: 1,924
Re: Bolts rear motor mount to clutch housing
Thanks...I can fit my thin-wall socket on the top bolt but there isn't enough space for the bottom bolts...These bolts have been there a long time...one place I read said use a 6" adjustable wrench...
|
Forum: Model A (1928-31)
06-01-2019, 03:05 PM
|
Replies: 7
Views: 1,924
Bolts rear motor mount to clutch housing
I can not get the bolts holding rear motor mount to clutch housing out...ordered a thin wall socket which goes on the top bolt but socket wrench won't budge it....any secret here I don't know about
|
Forum: Model A (1928-31)
01-19-2019, 11:28 AM
|
Replies: 10
Views: 2,323
Bolt against flywheel?
I was putting a new radius ball kit in....in putting in the new bolts in from hole, i had a string tied to the bolt through the cotter pin hole , it broke and the bolt has fallen forward toward...
|
Forum: Model A (1928-31)
12-20-2018, 10:51 PM
|
Replies: 4
Views: 1,178
|
Forum: Model A (1928-31)
12-20-2018, 05:28 PM
|
Replies: 4
Views: 1,178
Radius ball bolts
Can I replace the radius ball bolts without removing the transmission from the car?
|
Forum: Model A (1928-31)
11-23-2018, 10:53 PM
|
Replies: 9
Views: 1,988
|
Forum: Model A (1928-31)
10-28-2018, 06:36 PM
|
Replies: 5
Views: 1,508
Red Distributor
I have seen red bakelite model a distributors on some engines...are they available?
|
Forum: Model A (1928-31)
07-05-2018, 12:34 PM
|
Replies: 11
Views: 2,641
Re: Carburetor identify
Thanks...both look pretty good...is one considered better. And which would it pay to have rebuilt?
|
Forum: Model A (1928-31)
07-05-2018, 10:20 AM
|
Replies: 11
Views: 2,641
Carburetor identify
I received 2 extra carburetors with my Model A....neither one has a brand name..The one on the left has "model XF" the other has "Made in the USA"...
Can anybody help me identify the...
|
Forum: Model A (1928-31)
07-01-2018, 01:22 PM
|
Replies: 4
Views: 1,078
|
Forum: Model A (1928-31)
07-01-2018, 11:50 AM
|
Replies: 8
Views: 2,226
|
Forum: Model A (1928-31)
07-01-2018, 11:27 AM
|
Replies: 4
Views: 1,078
Alternate Ignition Switch
I am building a speedster with a wooden dash. I am not using a pop-out switch. Im using a pull out-push in switch. Im using basic Model A wiring, 12 volt, negative ground....My question is where do...
|
Forum: Model A (1928-31)
10-21-2017, 09:12 AM
|
Replies: 31
Views: 13,170
|
Forum: Model A (1928-31)
10-21-2017, 09:02 AM
|
Replies: 31
Views: 13,170
|
Forum: Model A (1928-31)
10-12-2017, 03:35 PM
|
Replies: 6
Views: 1,317
Re: Pop out switch problem
Since we are discussing pop out switches, I am building a speedster...I look at the wiring diagram and the switch is between the coil and the distributor ...I don't understand that placement...I want...
|
Forum: Questions & Suggestions
10-12-2017, 03:21 PM
|
Replies: 0
Views: 1,196
|
Forum: Model A (1928-31)
09-09-2017, 08:36 AM
|
Replies: 9
Views: 1,242
|
Forum: Model A (1928-31)
09-09-2017, 08:09 AM
|
Replies: 9
Views: 1,242
|
Forum: Model A (1928-31)
09-08-2017, 05:53 PM
|
Replies: 9
Views: 1,242
Model B Oil Tube
I have a Model B oil supply tube which is larger than the standard Model A tube...I can not find a source for a B cap ...Anybody know of where I might find one?
|
Forum: Model A (1928-31)
08-01-2017, 01:43 PM
|
Replies: 9
Views: 1,212
B head water pump
My model A speedster has a B head. The water pump and water outlet are built together. My question is where can I install the water temperature bulb for a water temperature gauge.?
|
Forum: Model A (1928-31)
07-25-2017, 03:58 PM
|
Replies: 8
Views: 1,669
|
Forum: Model A (1928-31)
07-25-2017, 10:27 AM
|
Replies: 8
Views: 1,669
Fan belt issue
I am putting on a new fan belt on my A but having real difficulty because the space between the crank pulley and the spring shackles is too narrow. Any suggestions?...thanks
|
Forum: Model-A
06-24-2017, 08:34 PM
|
Replies: 0
Views: 896
|