Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 70
Search took 0.01 seconds.
Search: Posts Made By: Bill Pursel
Forum: Model A (1928-31) 01-31-2019, 04:54 PM
Replies: 9
Views: 1,042
Posted By Bill Pursel
Re: Truck pictures

Bob great idea on making buisness cards
Forum: Model A (1928-31) 01-31-2019, 04:50 PM
Replies: 13
Views: 630
Posted By Bill Pursel
Re: 82a ccpu roof installation

Just done mine awhile back. Not that hard as it looks.2 person job.
Forum: Model A (1928-31) 01-27-2019, 05:22 PM
Replies: 6
Views: 470
Posted By Bill Pursel
Re: A-2492: Equalizer Operating Shaft Retracting Spring

Steve is anyone making this spring ? A friend of mine is putting together a fine point E28 and needs one.
Forum: Model A (1928-31) 01-27-2019, 05:14 PM
Replies: 17
Views: 904
Posted By Bill Pursel
Re: Brake Pills

Thats two beers
Forum: Model A (1928-31) 01-27-2019, 05:06 PM
Replies: 9
Views: 1,042
Posted By Bill Pursel
Truck pictures

Taken at and old factory in Terre Haute Ind
Forum: Model A (1928-31) 01-27-2019, 04:54 PM
Replies: 16
Views: 757
Posted By Bill Pursel
Re: Glass patterns 30 Ford coupe

they are in the Ford service bulletins...thats where I got sizes for mine.
Forum: Model A (1928-31) 12-12-2018, 04:39 PM
Replies: 2
Views: 377
Posted By Bill Pursel
Re: Grease fitting threads

most I have seen are ether 5\16 press in or 1/8 pipe
Forum: Model A (1928-31) 10-21-2018, 08:03 AM
Replies: 8
Views: 1,248
Posted By Bill Pursel
Re: "For-A-Ford" wrenches - what are they for?

look up a web site called alloy artifacts
Forum: Model A (1928-31) 09-13-2018, 11:45 PM
Replies: 18
Views: 1,255
Posted By Bill Pursel
Re: If Henry was on Twitter would anyone like him?

I appreciate his work but do not like the way he treated his son and hated jews etc.
Forum: Model A (1928-31) 09-10-2018, 05:28 PM
Replies: 5
Views: 1,134
Posted By Bill Pursel
Re: Surprise find

I have got an early engine that has x rods,5 journal cam and block and has a felt in the rear main like yours !
Forum: Model A (1928-31) 09-08-2018, 03:57 PM
Replies: 11
Views: 666
Posted By Bill Pursel
Re: Stuck Clutch Plate

If its stuck because of grease or oil accumulation you can spray it with brake clean thru the inspection and lube cover.
Forum: Model A (1928-31) 09-08-2018, 03:45 PM
Replies: 18
Views: 1,100
Posted By Bill Pursel
Re: Tool purchase advice

Grease in tubes now most are chassis and wheel bearing approved. I only use Lucas Red and Tacky approved for both.
Forum: Model A (1928-31) 09-08-2018, 03:40 PM
Replies: 9
Views: 545
Posted By Bill Pursel
Re: Installing tie rods without removing backing plate?

Take steering arms off spindle works too
Forum: Model A (1928-31) 09-08-2018, 06:29 AM
Replies: 5
Views: 525
Posted By Bill Pursel
Re: Lock tight

use the blue loktite
Forum: Model A (1928-31) 09-08-2018, 06:27 AM
Replies: 6
Views: 643
Posted By Bill Pursel
Forum: Model A (1928-31) 09-08-2018, 06:23 AM
Replies: 13
Views: 915
Posted By Bill Pursel
Re: Engine issue?

Other than a sticking valve the repair is going to require the head and side cover and manifold removal
Forum: Model A (1928-31) 09-08-2018, 06:18 AM
Replies: 18
Views: 1,100
Posted By Bill Pursel
Re: Tool purchase advice

This one made by Lisle works very good
Forum: Model A (1928-31) 09-02-2018, 05:34 AM
Replies: 15
Views: 1,043
Posted By Bill Pursel
Re: looking for a insert bearing thread

I think its TOP SECRET stuff
Forum: Model A (1928-31) 08-08-2018, 07:18 PM
Replies: 4
Views: 323
Posted By Bill Pursel
Re: Emergency brake cross shaft bearings

bushing should move smootly on cross shaft
Forum: Model A (1928-31) 07-25-2018, 05:11 PM
Replies: 2
Views: 306
Posted By Bill Pursel
Re: Head Lamps

socket is held in shell with adj. screw and spring without bulb -then place reflector on install bulb lens and retainer trim
Forum: Model A (1928-31) 07-25-2018, 04:59 PM
Replies: 6
Views: 386
Posted By Bill Pursel
Re: Generator Wiring Question

Here are wiring diagrams . None of your photos look correct
Forum: Model A (1928-31) 07-17-2018, 11:25 AM
Replies: 7
Views: 579
Posted By Bill Pursel
Forum: Model A (1928-31) 07-15-2018, 06:05 PM
Replies: 16
Views: 711
Posted By Bill Pursel
Re: pickup tail light mount

Here is how I made my block for a 3 hole bracket
Forum: Model A (1928-31) 07-14-2018, 10:35 AM
Replies: 19
Views: 1,686
Posted By Bill Pursel
Re: block crack

Again thanks all for the info. I am going to Helicoil the stud and seal it with Permotex and leave the cracks alone as they and the deck are flat. It had a Brumfield head on it which will not go back...
Forum: Model A (1928-31) 07-13-2018, 06:18 AM
Replies: 19
Views: 1,686
Posted By Bill Pursel
Re: block crack

Thank you all for your replies. Gonna run it that way.....
Showing results 1 to 25 of 70

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:51 AM.