Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: 69a
Forum: Early V8 (1932-53) 04-09-2021, 06:58 AM
Replies: 9
Views: 777
Posted By 69a
Re: Fuel pump just as a pass thru

Use a metal disc and use Viton, EPDM
Forum: Early V8 (1932-53) 03-20-2021, 04:28 AM
Replies: 2
Views: 352
Posted By 69a
Re: Need ID help on stainless trim,

Did you sort the timing issue?
Check your post!
Forum: Early V8 (1932-53) 03-19-2021, 08:03 PM
Replies: 83
Views: 4,787
Posted By 69a
Re: Trouble shoot 1950 8Ba initial start up Help

Did you sort out your timing?
Forum: Early V8 (1932-53) 03-07-2021, 07:06 PM
Replies: 32
Views: 1,434
Posted By 69a
Re: Installing 95% oil filter system issue

The thread by the pan rail is 1/8"NPT.
You can put any configuration of fittings and adapters and hoses. It is relatively low pressure.
Forum: Early V8 (1932-53) 03-07-2021, 06:04 PM
Replies: 32
Views: 1,434
Posted By 69a
Re: Installing 95% oil filter system issue

It sounds like you are describing the bypass system. You must fit a restrictor before the filter. preferably close to the block. It has a aprox 1/16" hole in it. If you don't fit this you run the...
Forum: Early V8 (1932-53) 03-02-2021, 11:14 AM
Replies: 83
Views: 4,787
Posted By 69a
Re: Trouble shoot 1950 8Ba initial start up Help

Check your own post #23.
Your ignition timing is out!
Forum: Early V8 (1932-53) 03-01-2021, 06:46 PM
Replies: 83
Views: 4,787
Posted By 69a
Re: Trouble shoot 1950 8Ba initial start up Help

It is obvious the rotor is pointing to #1 When it sparks!!! It Doesn't prove anything?????
Keep it simple. One step at a time. You are over thinking it when you don't have the first step sorted....
Forum: Early V8 (1932-53) 01-18-2021, 03:53 PM
Replies: 34
Views: 3,415
Posted By 69a
Re: Manifold vacuum at idle... vs without...interesting observations

If you set your timing at 0deg at idle with vacuum disconnected as soon as you connect the vacuum line you have 14deg advance at idle. WTF. SBC dizzy is designed to have the vacuum line connected...
Forum: Early V8 (1932-53) 01-18-2021, 06:08 AM
Replies: 34
Views: 3,415
Posted By 69a
Re: Manifold vacuum at idle... vs without...interesting observations

You don't connect the vacuum advance to the manifold. You are having the complete opposite effect.
Disconnect it!
Forum: Early V8 (1932-53) 09-08-2020, 02:28 AM
Replies: 20
Views: 1,428
Posted By 69a
Re: No Oil Pressure in 8BA

You need to open the oil line by removing the pressure gauge. The pump is cavating because the pickup tube is empty. Open up the oil line and crank it over until you get enough oil out to get the...
Showing results 1 to 10 of 10

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:40 AM.