Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: Al 29Tudor
Forum: Model A (1928-31) 01-26-2024, 10:30 AM
Replies: 17
Views: 1,120
Posted By Al 29Tudor
Re: Pace maker and the Model A

You guys are terrific! Thank you all so much for your responses and comments on your experiences. I plan to try to figure out which device is less sensitive to alternators and breaker points.
Thanks...
Forum: Model A (1928-31) 01-25-2024, 03:22 PM
Replies: 17
Views: 1,120
Posted By Al 29Tudor
Re: Pace maker and the Model A

Jay Jay and Joncrane, Thank you both very much for your comments and reassurance on my pacemaker concerns. Have a great afternoon.
Al
Forum: Model A (1928-31) 01-25-2024, 01:40 PM
Replies: 17
Views: 1,120
Posted By Al 29Tudor
Pace maker and the Model A

I have heard that Pacemaker's and the Model A ignition are not compatible. Our ignition systems are not shielded and give off electrical signals that can interfere with Pacemaker's.
Anybody have...
Forum: Model A (1928-31) 04-09-2023, 11:51 AM
Replies: 3
Views: 615
Posted By Al 29Tudor
Power House Generaor - Adjust

Is the power house generator adjustable like the regulat generator with the moveable brush ?
Thanks,
Al
Forum: Model A (1928-31) 03-19-2023, 03:14 PM
Replies: 0
Views: 357
Posted By Al 29Tudor
Rumble latch 1928

I'm assembling the latch for a rumbl lid on a 1928 sport coupe. After adding the hardware for the latch handle I find that the back cushion interferes with the dome nut on the shaft for the handle....
Forum: Model A (1928-31) 01-31-2023, 11:45 AM
Replies: 3
Views: 593
Posted By Al 29Tudor
28-29 panel cover for back of front seat

Is the back of the front seat spring covered befor it is installed in a rumble seat car ?
Thank you,
Al
Forum: Model A (1928-31) 01-30-2023, 11:26 AM
Replies: 2
Views: 507
Posted By Al 29Tudor
Re: 1928 Rumble area kick panels

Thank you mcgarrett
Forum: Model A (1928-31) 01-30-2023, 11:01 AM
Replies: 19
Views: 2,731
Posted By Al 29Tudor
Re: Classified Documents

Maybe someone else packed them for you !
Forum: Model A (1928-31) 01-30-2023, 10:44 AM
Replies: 2
Views: 507
Posted By Al 29Tudor
1928 Rumble area kick panels

I'm looking for some suggestions on what material to use to make the kick panels for a 28 model A rumble area. Has anyone used masonate or some kind of insulated panel material they can recommend ?...
Forum: Model A (1928-31) 01-06-2023, 01:56 PM
Replies: 2
Views: 706
Posted By Al 29Tudor
Re: Need 1928 Sport Coupe Rumble Seat and Back

Thank you Rotorwrench. I appreciate you help.
Al
Forum: Model A (1928-31) 01-05-2023, 04:46 PM
Replies: 2
Views: 706
Posted By Al 29Tudor
Need 1928 Sport Coupe Rumble Seat and Back

Hi All,
I'm starting a project to finish a friends Rumble area. The rumble area is empty so I will need the panels, seat, seat-back, and carpet for a beautiful 28 sport coupe in the tan color. Any...
Forum: Model A (1928-31) 04-18-2022, 10:10 AM
Replies: 16
Views: 2,460
Posted By Al 29Tudor
V8 Clutch vs. Standard

Is using a V8 clutch in a model A really worth it? And is it a very straight forward installation? Many changes are stated as "easy" then all the little problems pop up during the installation. Are...
Forum: Model A (1928-31) 12-16-2021, 02:48 PM
Replies: 8
Views: 1,173
Posted By Al 29Tudor
Re: Flat Head Ted Locking nuts

Thanks to all for your input I do appreciate it. It's so helpful to hear your experiences. Now to find 5/8 - 18 thin jam nuts.
Thanks again, Al
Forum: Model A (1928-31) 12-14-2021, 08:16 AM
Replies: 8
Views: 1,173
Posted By Al 29Tudor
Re: Flat Head Ted Locking nuts

Richard and Y-Blockhead thanks for your responses. This is what I'm learning - the info on line says to run the very short special tap through the back plate to "clean the threads". I think that...
Forum: Model A (1928-31) 12-13-2021, 10:23 PM
Replies: 8
Views: 1,173
Posted By Al 29Tudor
Flat Head Ted Locking nuts

What size are the Flat Head Locking nuts ?
I'm measuring about .612 diameter for the stud the locking nuts go on, Too small for a 5/8 - 18 thread. I'm working on a friends car without instructions,...
Forum: Model A (1928-31) 09-15-2021, 02:52 PM
Replies: 16
Views: 3,433
Posted By Al 29Tudor
V8 Clutch for model A

Can anyone tell me what the advantage of using a V8 clutch is over a stock clutch?
Someone said you can use the V8 clutch and lightent the flywheel.
Thanks for any guigance you can offer.
Al
Forum: Model A (1928-31) 09-10-2021, 09:45 AM
Replies: 7
Views: 1,126
Posted By Al 29Tudor
Re: Coup rumble lid

Wrndln, You are exactly on target with lower panel issue. I had a chance to view a photo album and on the second page it showed the bottom panel missing. I'll email you and if you get a chance maybe...
Forum: Model A (1928-31) 09-06-2021, 02:06 PM
Replies: 7
Views: 1,126
Posted By Al 29Tudor
Re: Coup rumble lid

Wrndln,
Thank you foe all the information.
The car I'm working on is a 1928 with a rear mounted spare tire and has a fantastic paint job.
It belongs to my friend.
Al
Forum: Model A (1928-31) 09-06-2021, 12:49 PM
Replies: 7
Views: 1,126
Posted By Al 29Tudor
Re: Coup rumble lid

Thank you Bob.
I hope to get to the car today with this new information.
Al
Forum: Model A (1928-31) 09-06-2021, 09:40 AM
Replies: 7
Views: 1,126
Posted By Al 29Tudor
Re: Coup rumble lid

Wrndln,
Great information. What you discribed is just what it looks like on this car.
How is the original stiffener fastened to the lower panel?
Thank you again,
Al Leach
Forum: Model A (1928-31) 09-05-2021, 02:46 PM
Replies: 7
Views: 1,126
Posted By Al 29Tudor
Coup rumble lid

The rumble seat panel on my friends coupe looks like if it is closed it will bind against the lower panel and not open again.
Can anyone give me advice on this issue ?
Are there adjustments to the...
Forum: Model A (1928-31) 08-22-2021, 08:37 AM
Replies: 9
Views: 1,331
Posted By Al 29Tudor
Re: Brake adjustment

Tom, I think all four brakes should com on at the same time. The 11" drums all around were as good as they understood at the time. However, todays larger discs and callipers in front show that at...
Forum: Model A (1928-31) 08-01-2021, 10:14 PM
Replies: 13
Views: 1,738
Posted By Al 29Tudor
Re: Shorting pitman arm

The turning radius will not increase because the radius is controlledby the king pin wedge nuts. The spindle will turn until it contacts the special domed nut and then stop.
Al
Forum: Model A (1928-31) 06-04-2021, 12:45 PM
Replies: 2
Views: 670
Posted By Al 29Tudor
Re: Hor Rod rattle

Thank you Bob
Forum: Model A (1928-31) 06-04-2021, 11:03 AM
Replies: 2
Views: 670
Posted By Al 29Tudor
Hor Rod rattle

What is the best way to keep the horn rod from vibrating insid the steering column?
Thank youfor your advice
Al
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:49 AM.