Forum: Model T (1909-1927)
12-01-2018, 10:48 AM
|
Replies: 8
Views: 3,302
Re: Rear Axle Housing woes
When I removed the rear wheels on my 13, the brake shoes were missing and one axel was shaft was shimmed.
I install rebuilt , lined brake shoes . The wheels are hitting the shoes . That may be why...
|
Forum: Model T (1909-1927)
08-07-2018, 11:48 PM
|
Replies: 2
Views: 1,369
Early Aluminum Hoods
How did the finish hold up on the early Aluminum hoods compared to the finishes on the steel components of the body and fenders ?
Any source for photos of the aged finish on such hoods where the...
|
Forum: Model T (1909-1927)
07-11-2018, 08:50 PM
|
Replies: 5
Views: 2,414
Re: Brass Radiator emblem
The fins on my old brass original radiator on my 13 has the "shadow" of a Ford emblem that was removed long ago . My 14 has no evidence of ever having a Ford emblem although the original owner had...
|
Forum: Model T (1909-1927)
07-08-2018, 12:54 PM
|
Replies: 5
Views: 2,414
|
Forum: Model T (1909-1927)
07-03-2018, 11:10 AM
|
Replies: 12
Views: 2,225
Intake manifold Gaskets for 1913
I have found that the 1912 and 1913 had Aluminum intake manifolds that had protuberances that entered into the intake port on the block casting .The copper crush gaskets for later models will not...
|
Forum: Model A (1928-31)
06-13-2018, 09:58 AM
|
Replies: 15
Views: 9,962
|
Forum: Model T (1909-1927)
02-07-2018, 09:38 AM
|
Replies: 9
Views: 4,956
|
Forum: Model T (1909-1927)
02-03-2018, 12:23 AM
|
Replies: 5
Views: 1,711
Re: Natural spoke wheels
Thanks. It seems all the brass Ts have seen had the black paint removed from the wooden spokes .
|
Forum: Model T (1909-1927)
02-02-2018, 07:39 PM
|
Replies: 5
Views: 1,711
Re: Natural spoke wheels
I did not state my question clearly . I was wondering when the Natural Finished spoke wheel ended and the black painted spokes started .
|
Forum: Model T (1909-1927)
02-02-2018, 12:38 AM
|
Replies: 5
Views: 1,711
|
Forum: Model T (1909-1927)
01-27-2018, 11:25 PM
|
Replies: 10
Views: 3,928
Re: Low mileage original T
I have a 1913 with what I think are the original floorboards. There is a 4"x 4" cutout in the floorboard below the speedometer on the passenger's side . Why would anyone have done this?
|
Forum: Model A (1928-31)
12-09-2017, 10:45 PM
|
Replies: 3
Views: 1,062
Re: Fuel Tank
After checking my other tank the device appears to be a device for plugging a leak.
|
Forum: Model A (1928-31)
12-03-2017, 11:53 PM
|
Replies: 3
Views: 1,062
|
Forum: Model A (1928-31)
12-03-2017, 02:38 PM
|
Replies: 3
Views: 1,062
Fuel Tank
Cleaning fuel tank on 31 coupe. On the bottom of the interior of the tank there is a flat 4 '' x 1/2" device. It lays flat and appears to go through the bottom of the tank and is oriented...
|
Forum: Model A (1928-31)
11-25-2017, 11:34 AM
|
Replies: 41
Views: 8,268
Re: persistent misfiring - help!
pigtail wire in the distributor and/or condenser are often culprits in a car that has been performing well before going bad.
You checked the compression but sometimes an exhaust valve may be...
|
Forum: Model A (1928-31)
11-19-2017, 08:34 PM
|
Replies: 8
Views: 1,554
Re: Timing A and B Models
I may not have been clear in my question on the B model Timing . I have timed my A models with the pin with no problems . A friend asked me to help him with his B Model which has been backfiring . I...
|
Forum: Model A (1928-31)
11-18-2017, 11:07 PM
|
Replies: 8
Views: 1,554
Timing A and B Models
Are A and B models static timed the same ? On the B does the pinset give you the increased advance the B requires . Read the instructions and timed B but getting bad back firing .
|
Forum: Model A (1928-31)
05-31-2017, 10:57 PM
|
Replies: 31
Views: 12,358
|
Forum: Model A (1928-31)
04-22-2017, 10:43 AM
|
Replies: 16
Views: 3,264
Re: hood support...dummy needs help
When I heard that 2nd
dropping sound" , I suspected "the worst" . I thought 2 screws were more easy than the support rods and radiator hoses but ; "Bit Again" .
|
Forum: Model A (1928-31)
04-21-2017, 11:36 PM
|
Replies: 16
Views: 3,264
Re: hood support...dummy needs help
I was removing the rear part that retains the hood hinge pin (I needed to remove the hood) .
When I removed the first machine screw , I heard something drop beneath the car . I thought I knocked a...
|
Forum: Model A (1928-31)
04-09-2017, 09:49 AM
|
Replies: 34
Views: 6,834
|
Forum: Model A (1928-31)
01-18-2017, 09:05 PM
|
Replies: 3
Views: 1,500
|
Forum: Model A (1928-31)
01-18-2017, 09:42 AM
|
Replies: 3
Views: 1,500
Sills
How are the body panels attached to the body Sills ?
|
Forum: Model A (1928-31)
11-25-2016, 10:51 PM
|
Replies: 35
Views: 8,349
Re: cowell lights
"cowl wiring had a SWITCH mounted system. the switch was part A13335 "
Where was this switch mounted ?
|
Forum: Model A (1928-31)
11-20-2016, 10:43 PM
|
Replies: 33
Views: 7,337
|