Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: jhowes
Forum: Model A (1928-31) Yesterday, 03:11 PM
Replies: 32
Views: 811
Posted By jhowes
Re: EOG's 1928 Model A Pickup

A really nice truck. The advice given is very good, I would add to change out the carb, the Tilly is not the best for this motor etc. Also look into engine pans and by all means check out the fan...
Forum: Model A (1928-31) 03-19-2020, 08:14 AM
Replies: 43
Views: 2,342
Posted By jhowes
Re: Coronavirus vs "A" Drive

I expect to pass anytime now but I wanted to finish the interior and paint my A first. Jack
Forum: Model A (1928-31) 03-15-2020, 08:40 AM
Replies: 43
Views: 1,678
Posted By jhowes
Re: Flywheel Housing Alignment

I would also like to ask Herm why brass shims, I have steel shims, isn't that OK to use. Also someone mentioned doing this in the car. Is that possible? Jack
Forum: Model A (1928-31) 02-22-2020, 04:55 PM
Replies: 23
Views: 1,091
Posted By jhowes
Re: Adding Guages

Ruth ' thanks for the reply but the line to the points goes through the ignition switch and it has to be broken and tied directly to the coil which is where I have my problem. This is the same as I...
Forum: Model A (1928-31) 02-22-2020, 02:16 PM
Replies: 23
Views: 1,091
Posted By jhowes
Re: Adding Guages

Ruth' Can you show how you wired the coil after the ignition switch? I sketched this out and found that I would have to break into the ignition cable that goes to the distributor to do this. Not...
Forum: Model A (1928-31) 02-11-2020, 09:09 AM
Replies: 5
Views: 518
Posted By jhowes
Re: The model a drag link/pitman arm

I also don't fall into the genius category but I am willing to take a guess If the ball were to the outside would the drag link hit the tire on a sharp left turn? Otherwise it must be a geometry...
Forum: Model A (1928-31) 01-07-2020, 09:34 AM
Replies: 24
Views: 2,092
Posted By jhowes
Re: Engine Stand

I'd be more concerned about the three wheeled engine stand. I had one fall on me and nearly did a lot of damage to my leg. Only 4 wheeled versions now. Jack
Forum: Model A (1928-31) 12-14-2019, 10:39 AM
Replies: 7
Views: 599
Posted By jhowes
Re: Body Kit

Need Pictures
Forum: Model A (1928-31) 12-11-2019, 09:10 AM
Replies: 25
Views: 2,183
Posted By jhowes
Re: Babbit vs Inserts

I don't know the answer to your question, but I have read the same thing. My model A has run for 90 years with the babbit, why change and invite new types of problems? Jack
Forum: Model A (1928-31) 12-11-2019, 09:04 AM
Replies: 11
Views: 424
Posted By jhowes
Re: 30 Tudor Windlace question.

The pictures are great, I think I have it now. If I were smart enough, I would post pictures of the finished product. Thanks again. Jack
Forum: Model A (1928-31) 12-10-2019, 06:16 PM
Replies: 11
Views: 424
Posted By jhowes
Re: 30 Tudor Windlace question.

Pictures would be helpful. What is the sill? Is it the top piece on the door? Jack
Forum: Model A (1928-31) 12-10-2019, 06:12 PM
Replies: 11
Views: 424
Posted By jhowes
Re: 30 Tudor Windlace question.

Pictures would be good. What is the sill? Jack
Forum: Model A (1928-31) 12-10-2019, 01:49 PM
Replies: 11
Views: 424
Posted By jhowes
Re: 30 Tudor Windlace question.

Bob, Does it go on the door frame in the car top and back or does it all go on the door like the front piece. Jack
Forum: Model A (1928-31) 12-10-2019, 01:45 PM
Replies: 8
Views: 758
Posted By jhowes
Re: differential oil

Thanks, I thought that I had a screwed up rear end.
Forum: Model A (1928-31) 12-10-2019, 11:26 AM
Replies: 11
Views: 424
Posted By jhowes
30 Tudor Windlace question.

I just read a reply to a 29 windlace question but my 30 is different. Is it true that the front piece is attached to the door where the metal slot piece is and the top and rear of the windlace is...
Forum: Model A (1928-31) 12-10-2019, 11:04 AM
Replies: 8
Views: 758
Posted By jhowes
differential oil

I rebuild my differential and now it is time to fill it up. The fill is on the down side of the pumpkin and I don't see how to get oil in it. Any ideas? Thanks Jack
Forum: Model A (1928-31) 11-22-2019, 09:51 AM
Replies: 58
Views: 5,963
Posted By jhowes
Re: Cracked Block

I hope you have good luck with your engine. I have one that was cracked but with my eyesight I couldn't be sure where the crack was. Solution, I used an epoxy that is designed for marine use. ...
Forum: Model A (1928-31) 11-11-2019, 09:24 AM
Replies: 25
Views: 1,121
Posted By jhowes
Re: Cold Weather Operation

When I was in college in the late 50's my Model A coupe was having engine trouble but I found a 1930 Chevy coach for $100. The chevy was a good substitute for the laid up Model A. School was a 4...
Forum: Model A (1928-31) 11-06-2019, 08:52 AM
Replies: 5
Views: 771
Posted By jhowes
Re: Zenith 2 tip

What happened to the (Haag 1332) wrench? Did he decided to make a few or a large run or none? Do any of you guys know? Jack
Forum: Model A (1928-31) 11-05-2019, 09:44 AM
Replies: 33
Views: 15,524
Posted By jhowes
Re: U-Joint Prepacking

How come I can't see Toms pictures of the u-joint? Jack
Forum: Model A (1928-31) 11-01-2019, 02:43 PM
Replies: 31
Views: 1,795
Posted By jhowes
Re: Cotter pins

Thanks Holdover, just what I wanted to know. Jack
Forum: Model A (1928-31) 11-01-2019, 11:57 AM
Replies: 31
Views: 1,795
Posted By jhowes
Re: Cotter pins

My question was more toward the nuts and bolts. I have used stainless nuts and bolts where I don't want rust to be seen and wondered if the strength was the same as the standard steel bolts. Jack
Forum: Model A (1928-31) 11-01-2019, 07:52 AM
Replies: 31
Views: 1,795
Posted By jhowes
Re: Cotter pins

I would like to ask another question on this subject. Are the stainless cotter pins strong enough? I have never known if the stainless bolts are as strong as the grade five bolts for example.
Forum: Model A (1928-31) 10-23-2019, 08:41 AM
Replies: 8
Views: 926
Posted By jhowes
Re: Machinery

I would also like to thank Brent for his input. We are using lead also, this is a teaching project. We first made bearings for a bench grinder with a seperate motor. It was fun and the young ones...
Forum: Model A (1928-31) 10-23-2019, 08:27 AM
Replies: 43
Views: 4,798
Posted By jhowes
Re: Front Tool Box

Werner, There are two versions of the tool box if you are talking about the one that fits between the frame horns on the front of the car. One is square like the picture posted. The other is...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:33 PM.