Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 76
Search took 0.01 seconds.
Search: Posts Made By: Bill Pursel
Forum: Model A (1928-31) 10-21-2019, 04:50 PM
Replies: 6
Views: 364
Posted By Bill Pursel
Re: Model A Volt Meter

Macs and Snyders sells replacements for the Model A
Forum: Model A (1928-31) 05-26-2019, 10:31 AM
Replies: 9
Views: 700
Posted By Bill Pursel
Re: Sealed beam headlight help

If your ground is hot then you have a bad ground.
Forum: Model A (1928-31) 05-26-2019, 10:25 AM
Replies: 36
Views: 6,270
Posted By Bill Pursel
Forum: Model A (1928-31) 05-26-2019, 10:21 AM
Replies: 23
Views: 1,800
Posted By Bill Pursel
Re: Tube shocks

The gas is only in there to help stop aeration of fluids inside.
Forum: Model A (1928-31) 04-27-2019, 07:01 AM
Replies: 7
Views: 699
Posted By Bill Pursel
Re: Could these 6v LEDs be used as tail lights?

led lights are polarity sensitive may not work with positive ground system
Forum: Model A (1928-31) 04-05-2019, 06:36 AM
Replies: 3
Views: 531
Posted By Bill Pursel
Re: Safe Oil Level

Mine likes the half mark too and I have no problems
Forum: Model A (1928-31) 01-31-2019, 04:54 PM
Replies: 9
Views: 1,443
Posted By Bill Pursel
Re: Truck pictures

Bob great idea on making buisness cards
Forum: Model A (1928-31) 01-31-2019, 04:50 PM
Replies: 18
Views: 1,422
Posted By Bill Pursel
Re: 82a ccpu roof installation

Just done mine awhile back. Not that hard as it looks.2 person job.
Forum: Model A (1928-31) 01-27-2019, 05:22 PM
Replies: 6
Views: 732
Posted By Bill Pursel
Re: A-2492: Equalizer Operating Shaft Retracting Spring

Steve is anyone making this spring ? A friend of mine is putting together a fine point E28 and needs one.
Forum: Model A (1928-31) 01-27-2019, 05:14 PM
Replies: 17
Views: 1,434
Posted By Bill Pursel
Re: Brake Pills

Thats two beers
Forum: Model A (1928-31) 01-27-2019, 05:06 PM
Replies: 9
Views: 1,443
Posted By Bill Pursel
Truck pictures

Taken at and old factory in Terre Haute Ind
Forum: Model A (1928-31) 01-27-2019, 04:54 PM
Replies: 16
Views: 1,021
Posted By Bill Pursel
Re: Glass patterns 30 Ford coupe

they are in the Ford service bulletins...thats where I got sizes for mine.
Forum: Model A (1928-31) 12-12-2018, 04:39 PM
Replies: 2
Views: 514
Posted By Bill Pursel
Re: Grease fitting threads

most I have seen are ether 5\16 press in or 1/8 pipe
Forum: Model A (1928-31) 10-21-2018, 08:03 AM
Replies: 8
Views: 1,550
Posted By Bill Pursel
Re: "For-A-Ford" wrenches - what are they for?

look up a web site called alloy artifacts
Forum: Model A (1928-31) 09-13-2018, 11:45 PM
Replies: 18
Views: 1,792
Posted By Bill Pursel
Re: If Henry was on Twitter would anyone like him?

I appreciate his work but do not like the way he treated his son and hated jews etc.
Forum: Model A (1928-31) 09-10-2018, 05:28 PM
Replies: 5
Views: 1,329
Posted By Bill Pursel
Re: Surprise find

I have got an early engine that has x rods,5 journal cam and block and has a felt in the rear main like yours !
Forum: Model A (1928-31) 09-08-2018, 03:57 PM
Replies: 11
Views: 889
Posted By Bill Pursel
Re: Stuck Clutch Plate

If its stuck because of grease or oil accumulation you can spray it with brake clean thru the inspection and lube cover.
Forum: Model A (1928-31) 09-08-2018, 03:45 PM
Replies: 18
Views: 1,566
Posted By Bill Pursel
Re: Tool purchase advice

Grease in tubes now most are chassis and wheel bearing approved. I only use Lucas Red and Tacky approved for both.
Forum: Model A (1928-31) 09-08-2018, 03:40 PM
Replies: 9
Views: 838
Posted By Bill Pursel
Re: Installing tie rods without removing backing plate?

Take steering arms off spindle works too
Forum: Model A (1928-31) 09-08-2018, 06:29 AM
Replies: 5
Views: 699
Posted By Bill Pursel
Re: Lock tight

use the blue loktite
Forum: Model A (1928-31) 09-08-2018, 06:27 AM
Replies: 6
Views: 871
Posted By Bill Pursel
Forum: Model A (1928-31) 09-08-2018, 06:23 AM
Replies: 13
Views: 1,231
Posted By Bill Pursel
Re: Engine issue?

Other than a sticking valve the repair is going to require the head and side cover and manifold removal
Forum: Model A (1928-31) 09-08-2018, 06:18 AM
Replies: 18
Views: 1,566
Posted By Bill Pursel
Re: Tool purchase advice

This one made by Lisle works very good
Forum: Model A (1928-31) 09-02-2018, 05:34 AM
Replies: 15
Views: 1,401
Posted By Bill Pursel
Re: looking for a insert bearing thread

I think its TOP SECRET stuff
Forum: Model A (1928-31) 08-08-2018, 07:18 PM
Replies: 4
Views: 475
Posted By Bill Pursel
Re: Emergency brake cross shaft bearings

bushing should move smootly on cross shaft
Showing results 1 to 25 of 76

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:09 AM.