Forum: Model A (1928-31)
07-04-2015, 02:52 PM
|
Replies: 3
Views: 1,520
|
Forum: Model A (1928-31)
07-04-2015, 01:47 PM
|
Replies: 3
Views: 1,520
Red's Headers
I'm installing a set of Red's Headers what do I TORQUE them too ?
Thank you Mike
|
Forum: Model A (1928-31)
04-14-2015, 06:36 PM
|
Replies: 1
Views: 1,157
Fender well cover
I'm looking to to see if anyone makes a patch to cover the wheel wells on a 1930-31 front fenders??
Thank you Mike
|
Forum: Model A (1928-31)
03-19-2014, 06:44 PM
|
Replies: 7
Views: 3,165
Kiwi model A quick change
Has anyone on here builded a Kiwi Quickchange? I looking for pictures of the pinion being installed and what was used to to set the bearing and pinion in the housing.
Thank you Mike
|
Forum: Model A (1928-31)
12-13-2013, 07:41 PM
|
Replies: 7
Views: 1,814
Re: inner axle shaft seals ??
Thanks to all,
I was thinking the inner seal was to be installed by the inner bearing race, but I see it is installed in the inside the axle housing on the outer side of the housing.
Mike
|
Forum: Model A (1928-31)
12-13-2013, 06:49 PM
|
Replies: 7
Views: 1,814
|
Forum: Model A (1928-31)
12-13-2013, 03:08 PM
|
Replies: 7
Views: 1,814
inner axle shaft seals ??
Help,
I'm going to rebuild my model a rearend and I'm getting the bearing and all for the job. But I can find how the seal will mount on the inner axles or the bells ?
Is it installed before the...
|
Forum: Model A (1928-31)
06-18-2013, 08:38 AM
|
Replies: 14
Views: 2,027
Re: Knocking
I did just install super winfield head and cam, at the same time I did the distributor.
So maybe the gas is to low in octane. Thank you all, I be working on this today and hope the timing and gas...
|
Forum: Model A (1928-31)
06-17-2013, 09:41 PM
|
Replies: 14
Views: 2,027
Re: Knocking
It is more clatter than thud knock, and it more when it's under load of on a up climb
Mike
|
Forum: Model A (1928-31)
06-17-2013, 06:37 PM
|
Replies: 14
Views: 2,027
Re: Knocking
I did about a year or so, not a lot of miles since I did
Mike
|
Forum: Model A (1928-31)
06-17-2013, 05:56 PM
|
Replies: 14
Views: 2,027
Re: Knocking
I'm running Mallory single point distributors.
Mike
|
Forum: Model A (1928-31)
06-17-2013, 05:44 PM
|
Replies: 14
Views: 2,027
Knocking
Hi,
I need some in site on this. My banger sound really good sitting as I speeding up the engine, but if I take it out for a ride it sound good and run strong. But as I running along and I speed it...
|
Forum: Model A (1928-31)
05-14-2013, 10:35 AM
|
Replies: 2
Views: 1,127
manifold gaskets
Help,
Do you guys use sealing on you intake & exhaust manifold, if so what do you use ??
Thank you Mike
|
Forum: Model A (1928-31)
11-26-2012, 04:23 PM
|
Replies: 9
Views: 2,172
Compression
What is the cylinder compression for a stock model A engine ????
Mike
|
Forum: Model A (1928-31)
05-05-2012, 12:39 PM
|
Replies: 2
Views: 1,367
|
Forum: Model A (1928-31)
04-29-2012, 05:25 PM
|
Replies: 2
Views: 1,367
F.A.S.T. Time Trial Event 7-7-12
The Guys of Central Coast (California) would like to invite you out to the F.A.S.T.
Time Trials event held in Santa Margarita on July 7th, 2012.
So tune up your old ride and come on out!
(See...
|
Forum: Model A (1928-31)
03-31-2012, 10:50 AM
|
Replies: 4
Views: 1,003
Re: New cam
Thank you guys I plan to change oil pump and lifers at the same time.
Mike
|
Forum: Model A (1928-31)
03-31-2012, 10:31 AM
|
Replies: 4
Views: 1,003
New cam
Can a cam be installed with the engine still in the car?
Mike
|
Forum: Model A (1928-31)
02-23-2012, 12:56 PM
|
Replies: 1
Views: 820
Oil Pump
Hi,
Who makes and sells a higher out put Oil pump for model A engine?
Mike
|
Forum: Model A (1928-31)
10-25-2011, 03:30 PM
|
Replies: 8
Views: 2,120
|
Forum: Model A (1928-31)
10-25-2011, 03:00 PM
|
Replies: 8
Views: 2,120
Pitman arm
Help,
Installed a shorted pitman arm on my 1930 pickup which already had a dropped
axle. The pitman arm was install with the ball facing out, have seen picture of the pitman ball facing the frame,...
|
Forum: Model A (1928-31)
10-01-2011, 06:47 PM
|
Replies: 5
Views: 1,702
|
Forum: Model A (1928-31)
09-30-2011, 06:03 PM
|
Replies: 5
Views: 1,702
Re: Light switch rod
Steve
Not sure as it's installed in the pickup and would have to remove the steering column from pickup to pull it out to check the length. But I'm sure I have to remove in time to make right.
Mike
|
Forum: Model A (1928-31)
09-30-2011, 05:05 PM
|
Replies: 5
Views: 1,702
Light switch rod
Hi,
Installed a f-100 modified steering box for the model A's, in my 1930 model Pickup, and need to know how much of the light switch rod (by inches) sticks out the end. As the rod I have is to...
|
Forum: Model-A
06-09-2011, 01:59 PM
|
Replies: 0
Views: 659
Model A rear end
Want, a Model A rear end, I am in the central coast of Ca. area.
Mike
|