Forum: Model A (1928-31)
08-06-2020, 10:23 AM
|
Replies: 14
Views: 2,723
Re: Speedo is “jumpy”
How did you make out with this issue?
My speedo was jumping all over the place then pegged at zero. I could hear the cable banging around for a bit then it stopped and speedo started working again...
|
Forum: Model A (1928-31)
08-06-2020, 10:09 AM
|
Replies: 30
Views: 3,729
Re: Battery Isolator switch
Thank you to all. Installation of switch went well. installed right at my feet, in front of driver's side of seat. Parasitic drain is something to do with the new cutout switch I installed on the...
|
Forum: Model A (1928-31)
07-31-2020, 01:48 PM
|
Replies: 30
Views: 3,729
|
Forum: Model A (1928-31)
07-31-2020, 01:47 PM
|
Replies: 30
Views: 3,729
|
Forum: Model A (1928-31)
07-29-2020, 03:19 PM
|
Replies: 30
Views: 3,729
Re: Battery Isolator switch
Hi Bill. Unfortunately I don't understand what you mean by "In Series".
I have a switch that has one long red lead and one long black lead.
Both are battery cable gauge.
|
Forum: Model A (1928-31)
07-29-2020, 03:13 PM
|
Replies: 30
Views: 3,729
|
Forum: Model A (1928-31)
07-29-2020, 03:12 PM
|
Replies: 30
Views: 3,729
Re: Battery Isolator switch
I would agree with you but when it comes to electrical I'm not the swiftest.
I replaced the cutout switch on the generator with a switch that has the diode in it but the drain got worse.
This...
|
Forum: Model A (1928-31)
07-29-2020, 11:41 AM
|
Replies: 30
Views: 3,729
|
Forum: Model A (1928-31)
07-29-2020, 11:23 AM
|
Replies: 30
Views: 3,729
Re: Battery Isolator switch
By the way I might not be calling this switch by the right name. Basically I want to install a switch that cuts power from battery to the car.
|
Forum: Model A (1928-31)
07-29-2020, 11:20 AM
|
Replies: 30
Views: 3,729
Battery Isolator switch
I have a 1930 Model A with 6 volt positive ground system.
I have to take the fuse off of the starter as soon as I shut the engine off or the battery will drain.
I want to install a battery isolator...
|
Forum: Model A (1928-31)
05-25-2020, 08:27 AM
|
Replies: 18
Views: 3,110
Re: stripped Threads coolant fitting Model A
Thank you everyone that made suggestions and to all that were there in spirit. I finally tackled installing the helicoil for the coolant fitting in my A.
I have to tell you I was nervous and kept...
|
Forum: Model A (1928-31)
04-13-2020, 11:26 AM
|
Replies: 18
Views: 3,110
Re: stripped Threads coolant fitting Model A
Thank you all for the advice. I have a few blocks of mahogany that I can make a jig out of to hold the drill straight. I like the idea of taping the drill bit as well so I don't go too deep. All...
|
Forum: Model A (1928-31)
04-09-2020, 02:52 PM
|
Replies: 18
Views: 3,110
|
Forum: Model A (1928-31)
04-09-2020, 01:04 PM
|
Replies: 18
Views: 3,110
|
Forum: Questions & Suggestions
04-09-2020, 12:36 PM
|
Replies: 1
Views: 1,310
Model A stripped threads
I have a 1930 Model A Fordor with "original" engine setup. One of the bolts that fastens the coolant tube to the engine block is stripped. It holds all the way in and when I'm turning what I feel...
|
Forum: Model A (1928-31)
03-22-2019, 05:39 PM
|
Replies: 7
Views: 1,496
|
Forum: Model A (1928-31)
03-22-2019, 03:24 PM
|
Replies: 7
Views: 1,496
|
Forum: Model A (1928-31)
03-22-2019, 03:09 PM
|
Replies: 7
Views: 1,496
Adjustment Needle Driver
I need to replace the Adjustment needle driver on the carb for my 1930 Model A. does anyone know how I would tell if I need one that is "Pinned" or "Unpinned"? Model A newbie.
|