Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: 51 MERC-CT
Forum: Early V8 (1932-53) Yesterday, 07:41 AM
Replies: 19
Views: 545
Posted By 51 MERC-CT
Re: What kind of heads are these - 49 Merc flathead?

The head with no Mercury ID is probably a replacement head and it does not have the cast in oil filter mounting bosses. (most likely'48 '49 Ford car/truck or '49 Mercury)
This could be a Ford engine...
Forum: Early V8 (1932-53) 09-12-2019, 07:41 PM
Replies: 4
Views: 112
Posted By 51 MERC-CT
Re: 52 Rubber Bump Stop

Just plugs into the hole.
I have always used just soapy water to install.
https://www.fordbarn.com/forum/attachment.php?attachmentid=406727&d=1568335219
Forum: Early V8 (1932-53) 09-12-2019, 05:17 AM
Replies: 17
Views: 7,659
Posted By 51 MERC-CT
Re: Power steering pump on a flathead

This is the component layout for the '53 power steering installation.
Forum: Early V8 (1932-53) 09-11-2019, 06:38 AM
Replies: 18
Views: 666
Posted By 51 MERC-CT
Re: bleeding brakes

Just a thought, if foreign made it may be possible that these are made with metric threads (10mm x 1) pitch.
They are just slightly bigger than the 3/8" dia. standard ones that are used.
The 3/8...
Forum: Early V8 (1932-53) 09-11-2019, 06:09 AM
Replies: 6
Views: 225
Posted By 51 MERC-CT
Re: 53 cussy Lower Control Arm Shaft

The bushings are threaded into the control arm and should bottom out on it before any "pulling together" happens, then they are tightened to spec.
Forum: Early V8 (1932-53) 09-11-2019, 02:55 AM
Replies: 9
Views: 421
Posted By 51 MERC-CT
Re: Looking for info on CHAMPION cast iron Ford flathead cylinder heads.

It tells you who manufactured them in the ad you posted. And that they are a derivative of Fenton heads.
Suspect that the company has been out of business for a long time.
...
Forum: Early V8 (1932-53) 09-08-2019, 06:05 PM
Replies: 17
Views: 774
Posted By 51 MERC-CT
Re: What kind of air cleaner setup is this?

The Canadian Meteor is the equivalent of the US Ford and the intake system is totally different than the Monarch/Mercury.
The stuff attached below the air cleaner is not "extra" but part of the...
Forum: Early V8 (1932-53) 09-08-2019, 12:51 PM
Replies: 8
Views: 190
Posted By 51 MERC-CT
Re: Crankcase Vent PCV for 59A

The only way that it may be effective is to seal the oil breather/filler opening so that a vacuum can be formed to draw air thru the front oil pan breather.
Forum: Early V8 (1932-53) 09-08-2019, 06:35 AM
Replies: 17
Views: 774
Posted By 51 MERC-CT
Re: What kind of air cleaner setup is this?

Suggest that it is not military, farm or commercial but a 1951 Canadian Monarch air cleaner.
The one below is the 1949 version.


...
Forum: Early V8 (1932-53) 09-07-2019, 11:36 AM
Replies: 14
Views: 668
Posted By 51 MERC-CT
Re: Conversion to 6 volt, positive ground, LED headlights

Running the windows and top etc. on 12 volts would be interesting though.
Probably operate at super fast speed. :D
Forum: Early V8 (1932-53) 09-06-2019, 06:18 PM
Replies: 14
Views: 668
Posted By 51 MERC-CT
Re: Conversion to 6 volt, positive ground, LED headlights

They are out there but pricey.
They are 12 volt but the 6 volt bulbs that are available should work.


...
Forum: Early V8 (1932-53) 09-06-2019, 04:22 PM
Replies: 14
Views: 668
Posted By 51 MERC-CT
Re: Conversion to 6 volt, positive ground, LED headlights

Looks like an excellent way to go for those with 6 volt systems.
Did my 12 conversion about a month ago with the only issue being that the lens/reflectors were loose after assy. (a few dabs of...
Forum: Early V8 (1932-53) 09-06-2019, 04:04 PM
Replies: 14
Views: 436
Posted By 51 MERC-CT
Re: flex fan

Adapted a 7 blade flex-fan from a 70's vintage 6 cyl. Fairmont.
Pumps a lot of air and is quiet. (much better than stock)

...
Forum: Early V8 (1932-53) 09-06-2019, 12:58 PM
Replies: 18
Views: 568
Posted By 51 MERC-CT
Re: Ford engine factory break in process

Just wondering, the engines were most likely filled with oil for the process, was that oil removed and replaced with new oil for delivery.
Forum: Early V8 (1932-53) 09-06-2019, 10:13 AM
Replies: 18
Views: 568
Posted By 51 MERC-CT
Re: Ford engine factory break in process

Obviously not a plant worker but most likely an official stamping serial number commemorating build #1 as stated above.
Forum: Early V8 (1932-53) 09-06-2019, 08:19 AM
Replies: 18
Views: 568
Posted By 51 MERC-CT
Re: Ford engine factory break in process

That's the one.
https://www.fordbarn.com/forum/picture.php?albumid=5070&pictureid=41933
Forum: Early V8 (1932-53) 09-06-2019, 07:53 AM
Replies: 18
Views: 568
Posted By 51 MERC-CT
Re: Ford engine factory break in process

Yep, that's the process but I also remember another photo with many engines being run in at the same time.
Forum: Early V8 (1932-53) 09-06-2019, 06:01 AM
Replies: 18
Views: 761
Posted By 51 MERC-CT
Re: Sacrificial wire inside C69 Block?

Not sacrificial "anode" wire, but for support of the casting forms to prevent collapse during the casting process.
And you can remove it if you choose to.
This is an example....
Forum: Early V8 (1932-53) 09-05-2019, 08:07 AM
Replies: 5
Views: 328
Posted By 51 MERC-CT
Re: 39 Mercury question/mystery

Have not seen the photo you speak of but if it is an instructional photo, I would have to consider that a pre-production version of the vehicle may have been used to make the photo.
Forum: Early V8 (1932-53) 09-04-2019, 04:14 PM
Replies: 4
Views: 238
Posted By 51 MERC-CT
Re: 6 volt to 12 volt conversion

As stated there are sources of information in various places.
Considering that you are using a one wire Alt. this is a general idea of the one wire hookup and the other issues that need to be...
Forum: Early V8 (1932-53) 09-03-2019, 12:09 PM
Replies: 21
Views: 818
Posted By 51 MERC-CT
Re: Underhood carnage on my F-1

Fortunately you had a shroud installed otherwise you may have had a hole in the hood :eek:
Forum: Early V8 (1932-53) 09-02-2019, 07:30 PM
Replies: 24
Views: 739
Posted By 51 MERC-CT
Re: 1950 Mercury new member

These are two '49 Merc. sport sedans that I had (circa, fall 1957)
The one that I was customizing had the stainless accessory panel under the grille and the other one did not.
Needless to say the...
Forum: Early V8 (1932-53) 09-01-2019, 03:30 AM
Replies: 24
Views: 739
Posted By 51 MERC-CT
Re: 1950 Mercury new member

Yes, it would be interesting to know if it is truly "rack and pinion" equipped.
Forum: Early V8 (1932-53) 08-31-2019, 01:02 PM
Replies: 10
Views: 310
Posted By 51 MERC-CT
Re: Fitting a Fuel Pump

The 8BA fuel pump stand I have measures 2.600 to the C/L of the mounting bolts. That along with the thickness of the intake manifold (2.312) will give the overall distance to the intake mounting...
Forum: Early V8 (1932-53) 08-31-2019, 08:59 AM
Replies: 17
Views: 711
Posted By 51 MERC-CT
Re: What Car Skates work best?

I also bought these Harbor Freight dollies when they were on sale.

With coupons they were less than $200 for a set of 4.
Work well on 3000+pound vehicle on cement floor.

...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:44 AM.