Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 298
Search took 0.02 seconds.
Search: Posts Made By: figment
Forum: Model A (1928-31) 09-05-2019, 11:25 AM
Replies: 9
Views: 456
Posted By figment
Re: Horn Rod Reassembly in Column

Don't forget the small brass bushing at the very top of the steering shaft .
Forum: Model A (1928-31) 07-03-2019, 04:15 PM
Replies: 4
Views: 441
Posted By figment
Re: adjusting windshield in 30 coupe

Double check all the screws that hold the windshield to the wooden header . Sometimes the wood header is rotted and the screws will let the windshield frame set to low . Norm
Forum: Model A (1928-31) 06-15-2019, 01:10 PM
Replies: 23
Views: 1,624
Posted By figment
Re: Masking Carburetor

I have cadimum plated pins . The pins shown in number 14 are the stops for the choke and idle .
Forum: Model A (1928-31) 06-11-2019, 09:29 AM
Replies: 26
Views: 1,649
Posted By figment
Re: Help rear main leak

Make sure the gasket between the flywheel housing and the engine block is installed correctly . If it is installed backwards it will leak oil out the camshaft and it will run down the rear main area...
Forum: Model A (1928-31) 06-08-2019, 12:39 PM
Replies: 26
Views: 1,769
Posted By figment
Re: Prices Up ?

Remember Keith , if your buyer listed the car on Ebay there was at least 2 interested bidders so once listed he doesn't have much control on the final price . The other way he might have listed...
Forum: Model A (1928-31) 06-08-2019, 12:15 PM
Replies: 11
Views: 916
Posted By figment
Re: Looking for a clear oil...

I have seen clock oil that was clear . I was also told that musical instruments use a clear oil . Maybe you are looking for oil for the crankcase? Norm
Forum: Model A (1928-31) 06-05-2019, 04:25 PM
Replies: 1
Views: 271
Posted By figment
Re: Correct door latch screws into wood?

I have oval head nickle plate wood screws on my 68B , I'm not sure of the length .
Forum: Model A (1928-31) 06-04-2019, 06:02 PM
Replies: 21
Views: 1,410
Posted By figment
Re: Zenith rebuilds

Those carbs are on Ebay
Forum: Model A (1928-31) 06-04-2019, 06:01 PM
Replies: 21
Views: 1,410
Posted By figment
Re: Zenith rebuilds

There is a Model A good guy that is selling rebuilt and tested zenith carbs for about $169 to $189 . . The best price that I have seen .
Forum: Model A (1928-31) 05-19-2019, 07:53 PM
Replies: 9
Views: 830
Posted By figment
Re: What correct screws and/or fasteners are needed?

I understand that someone is or was going to make the special washers for the floorboard screws , I sent him a sample of the original . Now I don't remember who it was . Norm
Forum: Model A (1928-31) 01-23-2019, 08:42 PM
Replies: 19
Views: 1,690
Posted By figment
Re: Vibration

Make sure that the fan is balanced and if original check for cracks .
Forum: Model A (1928-31) 01-23-2019, 08:35 PM
Replies: 12
Views: 870
Posted By figment
Re: window regulators.

Try Arizona Model A , Ask for Sammy . He has a lot of original parts and is quite reasonable .
Forum: Model A (1928-31) 01-22-2019, 06:25 PM
Replies: 7
Views: 676
Posted By figment
Re: Cabriolet trim piece

You probably will need both the rubber spacer and the chrome plated cover that fits over the rubber spacer . Norm
Forum: Model A (1928-31) 01-17-2019, 05:40 PM
Replies: 10
Views: 807
Posted By figment
Re: Roadster Door Knob

I have an original knob that is 8 sided and is 9/16 wrench size . The top has the look like the one on the right with the double bump .
Forum: Model A (1928-31) 11-26-2018, 09:24 AM
Replies: 8
Views: 759
Posted By figment
Re: Windshield gasket on a 30 Briggs Town sedan

If you are using a reproduction gas cap it might sit to tall . I used a original and the windshield opened and closed as it should .
Forum: Model A (1928-31) 11-07-2018, 03:03 PM
Replies: 4
Views: 450
Posted By figment
Re: Windshield rubber

Don't trim right after after installation let it set for a few days because the rubber seal tends to shrink up somewhat .
Forum: Model A (1928-31) 10-29-2018, 05:48 PM
Replies: 4
Views: 372
Posted By figment
Re: 1930 Cabriolet pass door lock question

The original keeper screw is only about 1/4 inch long and is slotted . When seated against the lock it does go quite deep into the door wood . I have not seen one broken because it is so short . But...
Forum: Model A (1928-31) 10-25-2018, 03:42 PM
Replies: 127
Views: 11,984
Posted By figment
Re: Model A cross-country migration

Trying to follow on face book but The Rambling Macks will not bring anything up . Have i got it right?
Forum: Model A (1928-31) 09-19-2018, 02:21 PM
Replies: 13
Views: 1,142
Posted By figment
Re: Transmission locked in Reverse

If the ring gear is installed on the wrong side you would have 3 speeds in reverse and 1 speed forward
Forum: Model A (1928-31) 09-11-2018, 10:06 PM
Replies: 3
Views: 494
Posted By figment
Re: Gilmore crowd?

There is plenty of parking . The swap meets in the past were small to medium but the parts are very nice . I believe this year might be the largest swap meet yet . I also believe there will be a good...
Forum: Model A (1928-31) 08-27-2018, 01:26 PM
Replies: 7
Views: 900
Posted By figment
Re: Model A Day Swap Registration open!

I hope you reserved a nice shady spot for me ? Norm
Forum: Model A (1928-31) 08-22-2018, 07:24 PM
Replies: 9
Views: 993
Posted By figment
Re: Gas peddle & footrest escutcheon 's

The foot rest base on the right with four screw holes is for the early Model a's
Forum: Model A (1928-31) 08-19-2018, 10:02 AM
Replies: 9
Views: 993
Posted By figment
Forum: Model A (1928-31) 08-15-2018, 08:44 PM
Replies: 7
Views: 560
Posted By figment
Re: 1930 Cabriolet window slide bar

I think you meant to type windshield slide bar .
Forum: Model A (1928-31) 08-13-2018, 08:15 PM
Replies: 12
Views: 1,096
Posted By figment
Re: Fire wall grommet

The cup washer and spring also had a small leather washer against the firewall.
Showing results 1 to 25 of 298

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:12 PM.