Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 23 of 23
Search took 0.00 seconds. Search: Posts Made By: [email protected]
Forum: Early V8 (1932-53) 02-28-2023, 09:07 AM
Replies: 2
Views: 414
Posted By [email protected]
A head on B engine

Will a model a head fit on a model B engine
Forum: Model A (1928-31) 02-28-2023, 09:04 AM
Replies: 10
Views: 2,226
Posted By [email protected]
Model a head on model b engine

Will a model a head fit on a model B engine
Forum: Model A (1928-31) 01-26-2023, 08:35 AM
Replies: 39
Views: 5,477
Posted By [email protected]
Re: Rear Main Bearing Oil Flow Study

thank you good post
Forum: Model A (1928-31) 01-26-2023, 08:34 AM
Replies: 39
Views: 5,477
Posted By [email protected]
Re: Rear Main Bearing Oil Flow Study

:):)
Forum: Model A (1928-31) 03-04-2022, 04:39 PM
Replies: 6
Views: 897
Posted By [email protected]
Re: Balance weights moving

We did the same thing on the 650 Yamaha snow pro sled that we raced years ago
Forum: Model A (1928-31) 03-04-2022, 01:33 PM
Replies: 6
Views: 897
Posted By [email protected]
Re: Balance weights moving

You look at the picture close the balance weight has two marks on the crank into marks on the weight and they don’t line up I wonder if that’s the amount that it has moved
Forum: Model A (1928-31) 03-04-2022, 12:59 PM
Replies: 6
Views: 897
Posted By [email protected]
Balance weights moving

Balance weights moving is it possible for the balance weights on a 32 engine that a full circle weights to move in cause a slight vibration
Forum: Model A (1928-31) 03-03-2022, 01:45 PM
Replies: 36
Views: 5,977
Posted By [email protected]
Re: Need Photo of Crank Counterweight

I have a model B engine with for full circle weights on the crank but it still has a small vibration I wonder if they can move
Forum: Model A (1928-31) 03-03-2022, 01:39 PM
Replies: 36
Views: 5,977
Posted By [email protected]
Re: Need Photo of Crank Counterweight

I have a model B engine which full circle balance weights have been added but I think one of them could have moved I have a slight vibration
Forum: Model A (1928-31) 03-03-2022, 10:08 AM
Replies: 36
Views: 5,977
Posted By [email protected]
Re: Need Photo of Crank Counterweight

My model B motor has full circle weights added on but I still get a small vibration it mid throttle485345
Forum: Model A (1928-31) 02-25-2022, 05:20 PM
Replies: 74
Views: 16,755
Posted By [email protected]
Re: T 5 5 speed VS Mitchell Transmission with overdrive

I installed t5 from a 1987S 10 Chevy 2 Wheel Dr. and it’s the best thing I ever did for that car it works perfectly
Forum: Model A (1928-31) 02-12-2022, 11:11 AM
Replies: 18
Views: 1,730
Posted By [email protected]
Re: What makes the model A have double the HP of a T

The best way I found to increase the power in a model a is to install a well balanced and blueprinted model B engine
Forum: Model A (1928-31) 02-12-2022, 11:04 AM
Replies: 6
Views: 2,641
Posted By [email protected]
Re: Coil & Ballast Resistor

The purpose of a ballast resistor is that when the points open and close faster on a 12 V car voltage will rise and as you slow down and go along and then idle you’ll get down to around 6 to 9 volts
Forum: Model A (1928-31) 02-09-2022, 09:17 AM
Replies: 1
Views: 546
Posted By [email protected]
ford plant

file:///C:/Users/dick/Pictures/ford.pdf
Forum: Model A (1928-31) 02-01-2022, 03:33 PM
Replies: 31
Views: 5,348
Posted By [email protected]
Re: Pressurized Radiator

The thermostat acts as a restrictor the water pump is pushing water too fast to the top of the radiator and it’s going out the overflow
Forum: Early V8 (1932-53) 01-27-2022, 11:49 AM
Replies: 7
Views: 1,589
Posted By [email protected]
Re: 1932 Model B 5-Window Loosing Water

Restrict the flow with either a 160 or 180 thermostat it will end your problems
Forum: Early V8 (1932-53) 01-24-2022, 06:32 PM
Replies: 7
Views: 819
Posted By [email protected]
Re: 32 banger head gasket

Thank you
Forum: Early V8 (1932-53) 01-24-2022, 11:32 AM
Replies: 7
Views: 819
Posted By [email protected]
32 banger head gasket

Can I get some opinions on which cylinder head gasket works best to cover the steam holes in the center of the model B head
Forum: Early V8 (1932-53) 01-21-2022, 09:43 AM
Replies: 3
Views: 697
Posted By [email protected]
Model B manifold

Will a model b intake manifold work with a model a exhaust manifold that has a heater
Forum: Model A (1928-31) 12-28-2021, 05:26 PM
Replies: 17
Views: 2,606
Posted By [email protected]
Re: Shimming axles

Used Loctite bearing mount when I shimmed my axles
Forum: Model A (1928-31) 12-26-2021, 10:20 AM
Replies: 4
Views: 763
Posted By [email protected]
Re: Axle shims

Thank you that makes me feel better
Forum: Model A (1928-31) 12-26-2021, 09:54 AM
Replies: 17
Views: 2,606
Posted By [email protected]
Shimming axles

Shimming axles I had to shim both axles is this going to work
Forum: Model A (1928-31) 12-26-2021, 09:52 AM
Replies: 4
Views: 763
Posted By [email protected]
Axle shims

Axle shims I would like to hear some opinions on shimming axles
Showing results 1 to 23 of 23

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:31 PM.