Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.15 seconds.
Search: Posts Made By: Purdy Swoft
Forum: Model A (1928-31) Yesterday, 06:28 PM
Replies: 9
Views: 473
Posted By Purdy Swoft
Re: Which 1931 hub cap to buy.

Actually I've never ran into the curb . Sometimes small dents can happen on the thin stainless hubcaps . If or when it happens , I don't try to beat the dent out . I turn the cap over on a smooth...
Forum: Model A (1928-31) Yesterday, 12:16 PM
Replies: 19
Views: 912
Posted By Purdy Swoft
Re: High compression head vs cooling

Mine still has the model A cackle or chick ah lunk as I call it at idle. They might not idle exactly as slowly as original , but they idle pretty slow with the spark retarded .
Forum: Model A (1928-31) 12-07-2019, 09:57 PM
Replies: 19
Views: 912
Posted By Purdy Swoft
Re: High compression head vs cooling

My heads are all cast iron . I prefer cast iron for durability , A lot of people have been running the Thomas finned aluminum heads for years , the aluminum heads must be doing some good or people...
Forum: Model A (1928-31) 12-07-2019, 05:05 PM
Replies: 19
Views: 912
Posted By Purdy Swoft
Re: High compression head vs cooling

Besides the 5.9 head , I run the super street Winfield 3/4 race cam , lighter model B flywheel , dual updraft model B carburetors and a few other minor mods . My model A idles smoothly and has the...
Forum: Model A (1928-31) 12-07-2019, 12:35 PM
Replies: 9
Views: 473
Posted By Purdy Swoft
Re: Which 1931 hub cap to buy.

Sometimes it can happen .
Forum: Model A (1928-31) 12-07-2019, 11:17 AM
Replies: 9
Views: 473
Posted By Purdy Swoft
Re: Which 1931 hub cap to buy.

I prefer the stainless steel 30-31 hub caps without the steel inner liner . I can usually straighten the stainless steel caps without the steel inner lining when they get bent . I used the domed at...
Forum: Model A (1928-31) 12-07-2019, 10:43 AM
Replies: 19
Views: 912
Posted By Purdy Swoft
Re: High compression head vs cooling

I'm still running 5.9 compression heads on some of my model A's and they run cooler than original .
Forum: Model A (1928-31) 12-03-2019, 02:18 PM
Replies: 14
Views: 494
Posted By Purdy Swoft
Re: Alternator Replacement 12V

The twelve volt one wire alternators offered by model A parts venders is probably less expensive than the ones offered locally . Years ago it was mentioned that NAPA offers some model A distributor...
Forum: Model A (1928-31) 12-03-2019, 01:45 PM
Replies: 11
Views: 442
Posted By Purdy Swoft
Re: water pump end play how to stop?

I either use the longer water pump shaft and grind for at least six thousands clearance at the rear of the shaft where it meets inside the head . There is a collar that can be installed on the water...
Forum: Model A (1928-31) 12-02-2019, 11:00 PM
Replies: 13
Views: 525
Posted By Purdy Swoft
Re: Install generator

I haven't had a generator pulley come loose yet . I did once wring off a generator pulley bolt . smiley face
Forum: Model A (1928-31) 12-02-2019, 12:31 PM
Replies: 14
Views: 494
Posted By Purdy Swoft
Re: Alternator Replacement 12V

The twelve volt alternators that I've seen advertised in the model A parts catalogs are negative ground .
Forum: Model A (1928-31) 12-01-2019, 03:20 PM
Replies: 4
Views: 229
Posted By Purdy Swoft
Re: original piston pins

The center lock wrist pins can be driven out with a like size or near , deep wall socket and a hammer . I've never needed a press to remove or install center lock model A wrist pins .
Forum: Model A (1928-31) 12-01-2019, 11:30 AM
Replies: 13
Views: 525
Posted By Purdy Swoft
Re: Install generator

There is one bolt that attaches the generator pulley . It is so much easier to install the belt when the pulley is removed . I slip the belt in the groove of the pulley and only need to move the...
Forum: Model A (1928-31) 11-30-2019, 05:09 PM
Replies: 5
Views: 232
Posted By Purdy Swoft
Re: Generator Brush Adjustment

Yes , The slip ring will rotate only so far . If a voltage regulator is used it will allow the generator to cycle between higher and lower charge rate to prevent overcharging the battery . When a...
Forum: Model A (1928-31) 11-30-2019, 04:34 PM
Replies: 57
Views: 2,099
Posted By Purdy Swoft
Re: Using Ford Barn as an distraction

I'm so sorry to hear of your loss .
Forum: Model A (1928-31) 11-30-2019, 04:18 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

If the ignition switch is left on without the engine running , if the points are closed the coil will get hot whether a resistor is used or not . When a resistor is used with a six volt 1.5 ohm coil...
Forum: Model A (1928-31) 11-30-2019, 03:54 PM
Replies: 5
Views: 232
Posted By Purdy Swoft
Re: Generator Brush Adjustment

push downward on the adjustable brush that is pictured , to increase the charge rate . The slip ring should slightly rotate when pushed down or raised up .
Forum: Model A (1928-31) 11-28-2019, 02:14 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

I'm very sorry if I took things wrong . No hard feelings, just my bad . I'm sorry that I was Rude . Please forgive . Happy thanksgiving .
Forum: Model A (1928-31) 11-28-2019, 02:02 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

Thanks Pat I'm probably not going anywhere unless it gets worse . Sometimes I just get agrivated when I try to give what I feel may be helpful info and it seems that some will jump right on it . I...
Forum: Model A (1928-31) 11-28-2019, 01:17 PM
Replies: 17
Views: 498
Posted By Purdy Swoft
Re: Trans Bearings

I agree , replace all of the transmission bearings . When bearings begin to fail , the rollers can and will stack . When the rollers from the failed bearings stack it throws the gear teeth out of...
Forum: Model A (1928-31) 11-28-2019, 12:54 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

.


Maybe I was quick to anger . I thought I explained every detail of how I did my 12 volt setup . It just seemed to me that you and rotowrench were trying to say that what I did would result in...
Forum: Model A (1928-31) 11-28-2019, 11:58 AM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

Just because a performance coil is used doesn't mean that points and condensers will fail on a weekly basis or at all . If points and condensers are failing on a regular basis there are other...
Forum: Model A (1928-31) 11-27-2019, 11:55 PM
Replies: 4
Views: 994
Posted By Purdy Swoft
Re: Tom Wesenberg

Tom is probably mostly posting on the Vintage site .
Forum: Model A (1928-31) 11-27-2019, 11:24 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

The original model A coil was TAR filled , not oil Filled . Many times it makes NO difference what the original designer wanted !!! Modifications have always been the choice of the owner of the...
Forum: Model A (1928-31) 11-27-2019, 01:38 PM
Replies: 41
Views: 968
Posted By Purdy Swoft
Re: 12 volt coil with resistor

Some may want to run an original Ford script coil , Others may just not want to spend the money for a new coil . If running a six volt coil on twelve volts a resistor mounted at the coil connection...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:04 AM.