Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Lawrie
Forum: Early V8 (1932-53) 11-24-2020, 07:27 PM
Replies: 16
Views: 367
Posted By Lawrie
Re: Rear shocks on a 1936 fordor

There should be stronger desistance in one direction, and they are adjustable.and temp compensated, quite a good setup considering when they were made.
Lawrie
Forum: Early V8 (1932-53) 11-24-2020, 06:06 PM
Replies: 16
Views: 367
Posted By Lawrie
Re: Rear shocks on a 1936 fordor

You can fix them your self if you have access to a lathe, I have just done 6 shocks from the rear of a 33 and a set from the front.
I replaced the seals with modern O rings and turned the shaft down...
Forum: Early V8 (1932-53) 11-24-2020, 02:01 AM
Replies: 57
Views: 1,358
Posted By Lawrie
Re: Another Huge Loss to me

Tony , my thoughts are with you at this very hard time, mine went in 84, way too young.
But its great to have learnt so much from them,
take solace that you have good memories, and many friends...
Forum: Early V8 (1932-53) 11-23-2020, 05:37 PM
Replies: 19
Views: 783
Posted By Lawrie
Re: 33 in the hills

Looks like this , from a couple years back looking for an old gold mine,
Lawrie
Forum: Early V8 (1932-53) 11-23-2020, 03:55 PM
Replies: 19
Views: 783
Posted By Lawrie
Re: 33 in the hills

Lawson, all is great here're missed all the virus stuff,
Will post some picks of the B24 we were going to look athttps://www.ozatwar.com/ozcrashes/qld89.htm
We will be back up there in a month or...
Forum: Early V8 (1932-53) 11-22-2020, 05:38 PM
Replies: 19
Views: 783
Posted By Lawrie
Re: 33 in the hills

Also, way up in the top of the ranges we came across some rust as wife Carol calls it, looks like an old mudguard(fender) from a truck or something.

Lawrie
Forum: Early V8 (1932-53) 11-22-2020, 02:04 AM
Replies: 19
Views: 783
Posted By Lawrie
33 in the hills

Wife and I went away for a weekend in the 33 and our caravan, just a short trip about 60 miles down the valley, for a relaxing few days.
While there' we took a drive up into the hills in the 33 on...
Forum: Early V8 (1932-53) 11-18-2020, 11:25 PM
Replies: 14
Views: 751
Posted By Lawrie
Re: question and maybe a picture

On a similar note, what if you put an 8ba into an early car, where do the engine stay rods go,
Lawrie
Forum: Early V8 (1932-53) 11-18-2020, 09:43 PM
Replies: 32
Views: 1,552
Posted By Lawrie
Re: head stud removal

This sure has put up some different ideas in getting the studs out, for me this is always the worst job on prepping a block.
Good to see the other ways of doing it.
thanks Lawrie
Forum: Early V8 (1932-53) 11-17-2020, 07:13 PM
Replies: 32
Views: 1,552
Posted By Lawrie
Re: head stud removal

Tony.
I will bow to your years of experience.
And on a bad block will try it out.
I am paranoid about buggering up the blocks as they Are the thing to save.
I used to drill and muck around and...
Forum: Early V8 (1932-53) 11-17-2020, 03:42 PM
Replies: 32
Views: 1,552
Posted By Lawrie
Re: head stud removal

I do all the drilling after the pilot drill with left handed snap on drills.
Lawrie
Forum: Early V8 (1932-53) 11-17-2020, 02:52 AM
Replies: 32
Views: 1,552
Posted By Lawrie
Re: head stud removal

Got the last one out this morning,I drilled it with a pilot drilll out the the root die of the thread, then picked out the remainder of the stud ,came out great but took as long as getting the bother...
Forum: Early V8 (1932-53) 11-16-2020, 05:48 PM
Replies: 2
Views: 249
Posted By Lawrie
Re: 35 condenser

You can use a condenser like that one when using a rewound original coil, I use them on my fords.
What you do is put a 3/16 did screw in through the hole where the original condenser was , use a...
Forum: Early V8 (1932-53) 11-16-2020, 03:46 AM
Replies: 32
Views: 1,552
Posted By Lawrie
head stud removal

I had a good day today , got 47 of the head studs out of a C69A block, only one snapped off flush.
What I did was to cut them all off about 1/2 inch above the block with a 4in cutoff wheel on the...
Forum: Early V8 (1932-53) 11-10-2020, 07:09 PM
Replies: 20
Views: 793
Posted By Lawrie
Re: remembrance day

I too have photos of my grandfather who was in the first lot to land at Gallipoli ,35 days there and wounded, also fought in Pashendale .
The pics show him and mates on leave in London,with a note...
Forum: Early V8 (1932-53) 11-10-2020, 04:04 PM
Replies: 20
Views: 793
Posted By Lawrie
remembrance day

A special day today
https://www.youtube.com/watch?v=ucIKv1SVvXo
Lawrie
Forum: Early V8 (1932-53) 11-06-2020, 05:46 AM
Replies: 13
Views: 1,420
Posted By Lawrie
Re: Fond these in an attic

I still use the floaters ,even in my276 eng with 2.139 journals, they are great bearings and long lasting.
Lawrie
Forum: Early V8 (1932-53) 11-06-2020, 01:37 AM
Replies: 0
Views: 223
Posted By Lawrie
34 3 window

I see a long post on the likely number of 32 3w that remain , has any one done the same for the 33 and 34 3 w coupes.
Lawrie
Forum: Early V8 (1932-53) 11-01-2020, 11:33 PM
Replies: 15
Views: 498
Posted By Lawrie
Re: Carburetor Adjustment for 33 Ford

If you have no luck ,let me know and I could send you stuff from the service books
Lawrie
Forum: Early V8 (1932-53) 11-01-2020, 01:51 AM
Replies: 13
Views: 619
Posted By Lawrie
Re: Pinion Location in Banjo

I have just installed a 3.78 into a 33 housing, there is a small gap between the edge of the gears and the roller bearing,
I you use NOS Ford pinion bearings, a stock 33/34 housing and FORD gears...
Forum: Early V8 (1932-53) 10-27-2020, 05:42 PM
Replies: 28
Views: 2,141
Posted By Lawrie
Re: Perfect work bench

Jim, good to see you are back on deck, stay good .
Lawrie
Forum: Early V8 (1932-53) 10-24-2020, 09:52 PM
Replies: 22
Views: 918
Posted By Lawrie
Re: 32 Ford brake cross shaft assembly

I just replaced the shaft and bushings on our 33, got them from Barnfind here,$22 for the set ,fitted them up and both pedals are perfect now.
Lawrie
Forum: Early V8 (1932-53) 10-24-2020, 09:03 PM
Replies: 16
Views: 634
Posted By Lawrie
Re: 41 Distributor Helmet Style - Dwell

Has any one tried one with the dwell points inoperative.
Lawrie
Forum: Early V8 (1932-53) 10-21-2020, 05:57 PM
Replies: 12
Views: 704
Posted By Lawrie
Re: parts pickup

Mark, they are brackets so I can carry long things, like reo bar etc, and a king brown is a BIG dangerous snake ,lots there
Brian
the bonnet was on the A when I first bought it about 30 yrs ago...
Forum: Early V8 (1932-53) 10-20-2020, 08:08 PM
Replies: 12
Views: 704
Posted By Lawrie
parts pickup

Last week I went out in the scrub to a mates old farm, he has a collection of old fords ,and lots of ford ww2 trucks.
I picked up really nice set of 3.78 gears for our 33 spare rear,I stripped two...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:22 PM.