Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: streetdreams
Forum: Late V8 01-04-2020, 05:56 PM
Replies: 1
Views: 304
Posted By streetdreams
Forum: Late V8 01-04-2020, 05:55 PM
Replies: 1
Views: 315
Posted By streetdreams
Forum: Late V8 01-04-2020, 05:55 PM
Replies: 2
Views: 369
Posted By streetdreams
Forum: Late V8 01-04-2020, 05:54 PM
Replies: 6
Views: 1,167
Posted By streetdreams
Forum: Late V8 01-04-2020, 05:54 PM
Replies: 4
Views: 1,177
Posted By streetdreams
Forum: Late V8 01-04-2020, 05:53 PM
Replies: 1
Views: 201
Posted By streetdreams
Forum: Late V8 11-20-2019, 08:50 PM
Replies: 1
Views: 304
Posted By streetdreams
Ford 292-312 tri power setup

Ford Y-Block tri power set up. Edelbrock 573 intake and 3 Ford 94 carbs. The 573 intake is the large port intake, best used with ECZ-C and ECZ-G heads.
The carbs are ECG center carb and EBU end...
Forum: Late V8 11-09-2019, 04:11 PM
Replies: 1
Views: 201
Posted By streetdreams
1963 Fairlane 289 HiPo exhaust manifolds

One set of factory exhaust manifolds for 289 HiPo Fairlane application. These are very early take-offs for header installation, have been on the shelf for over 50 years and the condition of them is...
Forum: Late V8 (1954+) 11-09-2019, 04:00 PM
Replies: 14
Views: 553
Posted By streetdreams
Re: Two barrel card spacer with pcv

if you're using a 2100 Ford 2 bbl, just about any mid to late '60s 302 or 351W has what you want
Forum: Late V8 (1954+) 08-18-2019, 08:20 AM
Replies: 12
Views: 743
Posted By streetdreams
Re: Holley 1273-2S carburetor

My info has the Ford 4100 w/ 1.08 venturis at 480 cfm. The 1.12 4100 used typically on 390 engines is rated 600 cfm
Forum: Late V8 08-16-2019, 07:16 PM
Replies: 8
Views: 1,166
Posted By streetdreams
Re: Sell Ford 1.08 4100 4bbl carb

sale pending on 1.08
Forum: Late V8 08-15-2019, 08:51 PM
Replies: 4
Views: 1,177
Posted By streetdreams
Forum: Late V8 08-15-2019, 08:51 PM
Replies: 8
Views: 1,166
Posted By streetdreams
Forum: Late V8 08-15-2019, 08:50 PM
Replies: 6
Views: 1,167
Posted By streetdreams
Forum: Late V8 08-15-2019, 08:49 PM
Replies: 2
Views: 369
Posted By streetdreams
Forum: Late V8 08-15-2019, 08:49 PM
Replies: 1
Views: 310
Posted By streetdreams
Forum: Late V8 (1954+) 07-29-2019, 06:33 PM
Replies: 30
Views: 1,287
Posted By streetdreams
Re: original paint y blocks

Ron, heads on your motor are ECZ-C heads.
Forum: Late V8 (1954+) 07-28-2019, 08:17 AM
Replies: 15
Views: 767
Posted By streetdreams
Re: Will a 390 expansion tank fit a Y-Block?

Swap meet stuff. $10-15 tops.
Forum: Late V8 (1954+) 07-25-2019, 08:08 PM
Replies: 24
Views: 1,125
Posted By streetdreams
Re: Tuning For Speed-Major Tuning (Blueprinting)

I've always wondered, what does the "M" in 351M mean?
Forum: Late V8 (1954+) 07-25-2019, 02:40 PM
Replies: 24
Views: 1,125
Posted By streetdreams
Re: Tuning For Speed-Major Tuning (Blueprinting)

Sal, if you won't be so closed minded about this stuff, you might learn something.
Forum: Late V8 (1954+) 07-20-2019, 12:48 PM
Replies: 61
Views: 2,410
Posted By streetdreams
Re: 292 312 Ford Engine

This post is turning into fantasy land. A Y Block is a flathead with OHV heads? Really? Stopgap design? Incidentally, Ford was not concerned with US designed engines overseas. Ford of Germany,...
Forum: Late V8 (1954+) 07-19-2019, 09:20 PM
Replies: 61
Views: 2,410
Posted By streetdreams
Re: 292 312 Ford Engine

"its this or jeopardy.but really hes been told where to look and hasnt.take about 30 seconds to find what motot he has.look at the crank and see if the dots there.look over the oil filter and give us...
Forum: Late V8 (1954+) 07-19-2019, 02:07 PM
Replies: 61
Views: 2,410
Posted By streetdreams
Re: 292 312 Ford Engine

Still cannot determine engine size. The cross over exhaust is early, but I've seen 312 long blocks under that old exhaust and lifter galley covers.
Forum: Late V8 (1954+) 07-18-2019, 08:26 PM
Replies: 61
Views: 2,410
Posted By streetdreams
Re: 292 312 Ford Engine

There is a letter/number cast into the side of the block above the oil pan rail. If you see ECZ-xxxx-A or C, there is a good chance it is a 312. The only way for sure is to look on the crank flange...
Forum: Late V8 (1954+) 07-04-2019, 10:33 AM
Replies: 2
Views: 291
Posted By streetdreams
Re: Happy Independence Day - 4th July

God Bless America, God save the Queen
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:58 PM.