Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Brian T
Forum: Model A (1928-31) Yesterday, 01:19 PM
Replies: 2
Views: 251
Posted By Brian T
Re: Sealing wax on condenser?

The plug was for keeping out moisture, the vendors have them.
Forum: Model A (1928-31) 01-17-2020, 03:30 PM
Replies: 21
Views: 726
Posted By Brian T
Re: steering sector

I have yet to hear of any poorly made 7 tooth parts, there are only 2 adjustments to make, there are shims in the lower housing to remove the play in the bearings top and bottom of the worm gear, the...
Forum: Model A (1928-31) 01-17-2020, 02:05 PM
Replies: 24
Views: 1,037
Posted By Brian T
Re: Throttle shaft brass plug for zenith carbs

I don't think so, there is seldom any wear on that side of the shaft, I have
2 Zeniths hanging up that do not have them, I believe the plug would only be removed if the bushings have been replaced...
Forum: Model A (1928-31) 01-15-2020, 01:08 PM
Replies: 21
Views: 726
Posted By Brian T
Re: steering sector

The first thing I would do is make sure the pitman arm bolt is tight, it takes a lot of torqueing to make that clamp close up, if that doesn't fix it then I would recheck all the measurements in the...
Forum: Model A (1928-31) 01-13-2020, 03:24 PM
Replies: 630
Views: 262,526
Posted By Brian T
Re: Model A commercial vehicles picture thread!!

Pictured outside of a rock quarry UK, probably cooling of its brakes. The other picture is the same place 1986, note the road way has not changed.
Forum: Model-A 01-08-2020, 01:57 PM
Replies: 8
Views: 1,938
Posted By Brian T
Forum: Model-A 12-30-2019, 02:31 PM
Replies: 3
Views: 443
Posted By Brian T
Re: Valve seat repair tools

Here we go again.
Forum: Model-A 12-30-2019, 02:30 PM
Replies: 8
Views: 1,527
Posted By Brian T
Re: Piston Expanders

To the top,
Forum: Model A (1928-31) 12-30-2019, 02:11 PM
Replies: 3
Views: 242
Posted By Brian T
Marvel jet size.

I have 2 marvel carburetors that I am reassembling, I am sure that the idle jet size would be the same as any Zenith, 44-48?, it would make sense if it was both having the same throttle diameters,...
Forum: Model A (1928-31) 12-26-2019, 01:08 PM
Replies: 41
Views: 2,217
Posted By Brian T
Re: Revising gear box

Good day to you Werner,
If you go to this web site you will have all the information you could wish for, Tom Endy is very precise in all of his articles regarding model A Ford repairs, scroll down...
Forum: Model A (1928-31) 12-24-2019, 03:21 PM
Replies: 11
Views: 791
Posted By Brian T
Re: E-Zsteer draglink/track rod kit

I went with the Teflon kit, I found that the steel kits did not confirm to the new balls on the reconditioned steering arms, some would only contact the outer edge of the concave and others would...
Forum: Model A (1928-31) 12-20-2019, 03:24 PM
Replies: 8
Views: 677
Posted By Brian T
Re: Carb Screen

If you haven't done so I would suggest installing the pencil filter in the tank and
remove the filter at the carb, in my opinion there is better fuel flow without it.
Forum: Model A (1928-31) 12-20-2019, 03:13 PM
Replies: 32
Views: 1,976
Posted By Brian T
Re: Model "A" Merry Christmas

Best wishes to all here on the Barn, hoping for a prosperous and healthy new year for everyone.
Forum: Model-A 11-26-2019, 12:30 PM
Replies: 8
Views: 1,527
Posted By Brian T
Forum: Model-A 11-26-2019, 12:27 PM
Replies: 3
Views: 443
Posted By Brian T
Forum: Model A (1928-31) 11-04-2019, 12:36 PM
Replies: 21
Views: 1,208
Posted By Brian T
Re: Stubborn Zenith

Hi Tin Cup,
Be sure that the idle speed is down below 6-700 RPM or lower , and the GAV is almost closed, then set the idle air screw at 1.1/2, - just a thought.
Forum: Model-A 10-27-2019, 04:22 PM
Replies: 4
Views: 909
Posted By Brian T
Re: 28-29 AA Truck Parts.

make offers send for pics,
Forum: Model-A 10-27-2019, 04:10 PM
Replies: 3
Views: 443
Posted By Brian T
Forum: Model-A 10-27-2019, 04:08 PM
Replies: 8
Views: 1,527
Posted By Brian T
Forum: Model A (1928-31) 10-23-2019, 02:54 PM
Replies: 33
Views: 2,075
Posted By Brian T
Re: Failing gas tank sealant

Here are some pictures of the so called dirty leg, the sediment trap on the right is the one I made, I used 1/4 inch valves, the other picture I believe has larger valves which would allow for...
Forum: Model A (1928-31) 10-20-2019, 01:25 PM
Replies: 37
Views: 1,779
Posted By Brian T
Re: Help! Tie rod end install

Looks to me that updraught wins the prize, maybe the grease fitting or hole not bored deep enough.
Forum: Model-A 10-17-2019, 01:41 PM
Replies: 3
Views: 443
Posted By Brian T
Valve seat repair tools

Looking to find valve seat cutting tools, just the small sets with the 3 angle cutters, pilot,etc would be OK send pictures to, btreserdern@san.rr.com, thanks in advance.
Forum: Model-A 09-11-2019, 10:20 AM
Replies: 4
Views: 909
Posted By Brian T
Re: 28-29 AA Truck Parts.

To The Top. MAKE OFFERS THANKS.
Forum: Model-A 08-22-2019, 01:50 PM
Replies: 4
Views: 909
Posted By Brian T
Re: 28-29 AA Truck Parts.

To the top. MAKE OFFERS THANKS.
Forum: Model A (1928-31) 08-18-2019, 04:14 PM
Replies: 8
Views: 542
Posted By Brian T
Re: Model AA

Hello David,
Welcome, I have a 1929 which I have had for 10 years and have gathered much info since then, as Ernie said post some pictures, if you have a problem posting them E-mail them to me --...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:52 PM.