Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 423
Search took 0.03 seconds.
Search: Posts Made By: Bill OH
Forum: Early V8 (1932-53) 03-24-2024, 06:24 PM
Replies: 10
Views: 336
Posted By Bill OH
Re: stock NOS fomoco valve springs on a 236 @.050 .355 lift cam

I agree with John - 43s to small- use 45s and I use a 71 PV. And LZ springs are good.
Forum: Early V8 (1932-53) 03-08-2024, 02:27 PM
Replies: 16
Views: 711
Posted By Bill OH
Re: 1951 Ford, runs fine then runs bad.

You mention new wires - if they are resistance wires I would replace them with copper core wires. Packard 440 is a god wire. But give attention to the replacement of coil.
Forum: Early V8 (1932-53) 03-08-2024, 09:12 AM
Replies: 16
Views: 711
Posted By Bill OH
Re: 1951 Ford, runs fine then runs bad.

Try a new coil - heat is killing the coil you currently have. You have a 6 volt positive ground system - make sure the ignition switch wire is connected to the minus of the coil and the distributor...
Forum: Early V8 (1932-53) 02-10-2024, 06:58 PM
Replies: 9
Views: 653
Posted By Bill OH
Re: GENERATOR 40 Ford Sdn.

Use a digital volt ohm meter between the generator and the frame of the regulator to determine that zero ohms exist, if not connect the generator and the frame of the regulator with 16ga wire with...
Forum: Early V8 (1932-53) 12-23-2023, 04:55 PM
Replies: 22
Views: 1,243
Posted By Bill OH
Re: Ardun sales brochure

I used a slide rule thru college - very handy. I have one in my tool cabinet. Great memoriesI
Forum: Early V8 (1932-53) 11-13-2023, 11:44 AM
Replies: 11
Views: 803
Posted By Bill OH
Re: Bleed down on vacuum advance question

With the vacuum control on the distributor and the vacuum line disconnected, I advance the point plate by hand, then put my finger over the vacuum connection and the release the point plate and if...
Forum: Early V8 (1932-53) 10-29-2023, 03:40 PM
Replies: 2
Views: 459
Posted By Bill OH
Re: Timing tool jig help

I do not have a diagram, but the points act as a switch between the batteries (D or C cells) and the light on the side. OR you could use an Ohmmeter connected across the dizzy body and terminal for...
Forum: Early V8 (1932-53) 10-10-2023, 10:08 AM
Replies: 33
Views: 4,134
Posted By Bill OH
Re: 1937 model 74 blowing the blues

I purchased a 221 in 1950 - burned oil as you describe. I ran detergent oil and it cleared the problem. I also cleaned 3/4 inch of sludge out of the pan. I could always depend on 86 mph and even...
Forum: Early V8 (1932-53) 10-09-2023, 09:28 AM
Replies: 18
Views: 1,426
Posted By Bill OH
Re: Help !!!!! Belts

I use the long flat blade screwdriver between the generator and the ledge on the front of the intake.
Forum: Early V8 (1932-53) 10-07-2023, 07:13 PM
Replies: 18
Views: 1,426
Posted By Bill OH
Re: Help !!!!! Belts

Install the fan assembly and leave the two mounting bolts finger tight to allow the generator to be adjusted for its belt, then adjust the fan belt by sliding its mounting bracket up and tighten its...
Forum: Early V8 (1932-53) 10-06-2023, 12:06 PM
Replies: 17
Views: 1,154
Posted By Bill OH
Re: Heat/ Exhaust Rise Intake

I used cupped core plugs in the block - works very well and durable.
Forum: Early V8 (1932-53) 09-18-2023, 09:38 AM
Replies: 25
Views: 1,716
Posted By Bill OH
Re: 1947 Super Deluxe V8 engine ground strap?

I have a 38 Ford 221 that had a ground strap from the battery to the firewall and another ground strap from the firewall to the engine, all of which yielded a voltage drop of 0.35 volts.
Steel does...
Forum: Early V8 (1932-53) 09-11-2023, 05:18 PM
Replies: 32
Views: 2,124
Posted By Bill OH
Re: 1953 Mercury unusual plug condition

I would find a diagram of the runners of the intake manifold and I am of the opinion that one of barrels of the carb is feeding too much fuel. I would take a look at the main jets for size - do not...
Forum: Early V8 (1932-53) 09-10-2023, 08:18 PM
Replies: 18
Views: 1,196
Posted By Bill OH
Re: 1938 Dual Cowl Phaeton

But it is a fun car to drive in fair weather and you do not have to wash door glass. I removed the hot water heater. Open cowl vent and enjoy.
Forum: Early V8 (1932-53) 09-10-2023, 09:46 AM
Replies: 1
Views: 316
Posted By Bill OH
Re: Replacing front shocks..

No, been there, done that.
Forum: Early V8 (1932-53) 08-11-2023, 11:53 AM
Replies: 16
Views: 716
Posted By Bill OH
Re: Optima battery holdown?

I put my Optima battery on the diagonal and went across the top of it from hold down bolt to hold down bolt with 3/8 x 1/14 varnished oak.
Forum: Early V8 (1932-53) 07-29-2023, 11:43 AM
Replies: 15
Views: 914
Posted By Bill OH
Re: Charging System Issue

I ran a 16ga wire between the generator housing and the regulator frame and a digital ohm meter connected across those two points should read zero ohms with clean connections. Generator and...
Forum: Early V8 (1932-53) 07-20-2023, 10:02 AM
Replies: 9
Views: 594
Posted By Bill OH
Re: New carb and fuel pump start procedure?

I have used a neoprene gasket for years with out difficulty - cork gets hard and brittle. TerryS may have a stuck valve in the fuel pump - hit it with screw driver handle has solved that issue for...
Forum: Early V8 (1932-53) 07-14-2023, 03:45 AM
Replies: 19
Views: 1,049
Posted By Bill OH
Re: Oil Leaks and Flathead mechanic, Santa Ynez, CA

I slide a large piece of cardboard under the car in the garage and stay off of driveways, especially those of friends.
Forum: Early V8 (1932-53) 07-13-2023, 09:19 AM
Replies: 7
Views: 684
Posted By Bill OH
Re: 1933 stock v8 40 compression test results & advice welcome

Another method for removal: Disconnect coil wire and vacuum line from left side and remove 5/16ths cap screw from left side - you will need to remove left distributor cap. Now go to the right...
Forum: Early V8 (1932-53) 06-11-2023, 01:42 PM
Replies: 63
Views: 14,585
Posted By Bill OH
Re: Airtex E8902 Debacle

You are correct- Facet - my mistake in spelling. But it looks like the Bendix pump.
Forum: Early V8 (1932-53) 06-08-2023, 11:23 AM
Replies: 63
Views: 14,585
Posted By Bill OH
Re: Airtex E8902 Debacle

I use Fasco (Bendix) electric fuel pumps. Reliable.
Forum: Early V8 (1932-53) 06-07-2023, 07:32 PM
Replies: 37
Views: 2,698
Posted By Bill OH
Re: 8ba fuel pump rod getting stuck

Thanks for the report - hope your success continues!!!
Forum: Early V8 (1932-53) 06-07-2023, 05:36 PM
Replies: 6
Views: 620
Posted By Bill OH
Re: Vacuum advance brake

I backed the vacuum brake full off on my 38 distributor and I have done that as early as 1950 - top speed increased 12 mph. I think you will need to plug the vacuum port or line because if you...
Forum: Early V8 (1932-53) 06-07-2023, 05:22 PM
Replies: 13
Views: 1,477
Posted By Bill OH
Re: hard start only when hot

I had the same problem on a 221 Ford with stromberg carbs and the coil was rebuilt and still had the hot hard start problem. I put 4 -5 gaskets under the carb and installed cupped core plugs in the...
Showing results 1 to 25 of 423

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:13 PM.