Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: Club Coupe
Forum: Early V8 (1932-53) 04-01-2021, 07:42 AM
Replies: 6
Views: 346
Posted By Club Coupe
Re: shifts hard

Thanks to all of you for your replies. I'll start removing all the small parts tomorrow and clean and lubricate them before reassembly. I would start today but it's that time of year for my first...
Forum: Early V8 (1932-53) 03-31-2021, 04:38 PM
Replies: 6
Views: 346
Posted By Club Coupe
Re: shifts hard

Thanks, Bob. Looks like I need to pull the entire steering column out. Rats!
Forum: Early V8 (1932-53) 03-31-2021, 03:57 PM
Replies: 6
Views: 346
Posted By Club Coupe
shifts hard

1950 Club Coupe. Shifting from first to second I raise the shift arm up to neutral and the spring does not pull the lever down to go on into second. I must push it forward then on into second It has...
Forum: Early V8 (1932-53) 10-21-2020, 07:46 PM
Replies: 3
Views: 343
Posted By Club Coupe
Re: knob on choke cable

Thank you both. I plan to reuse the know so I will try that tomorrow.
Forum: Early V8 (1932-53) 10-21-2020, 04:40 PM
Replies: 3
Views: 343
Posted By Club Coupe
knob on choke cable

I have a bad choke cable on my 1950 Ford. I can't get the old knob off. I tried screwing it off and pulling it straight off but nothing gives. What am I doing wrong? Can one of you advise me?
Forum: Early V8 (1932-53) 01-04-2020, 06:51 PM
Replies: 4
Views: 616
Posted By Club Coupe
Re: Drill a hole in the floor?

Thanks, 40cpe. At least I will know the hole's in the right place.
Forum: Early V8 (1932-53) 01-04-2020, 06:38 PM
Replies: 4
Views: 616
Posted By Club Coupe
Dtill a hole in the floor?

I am considering installing an OD tranny in my 1950 Ford. I have been offered one for $700which has been pro rebuilt. After doing some reading and Youtubing it looks like (among several other things)...
Forum: Model A (1928-31) 01-04-2020, 05:40 PM
Replies: 3
Views: 825
Posted By Club Coupe
a hole in my floorboard??!!

I am considering putting an OD tranny in my 1950 Ford. I have a rebuilt one available for $700. After reading and watching YouTube videos it seems that (among other things) I will need to drill a...
Forum: Questions & Suggestions 01-04-2020, 02:24 PM
Replies: 1
Views: 591
Posted By Club Coupe
A hole in my floorboard???

I am considering installing an OD tranny in my '50 club coupe. I have been offered a rebuilt one for $700. After doing a little research, it looks like I may have to drill a hole in my floorboard for...
Forum: Early V8 (1932-53) 11-23-2019, 09:20 PM
Replies: 14
Views: 1,116
Posted By Club Coupe
Re: gear ratio

Thanks, friends. I'm sure this will not work in my '50. I just wondered what car had a gearing that high. I would have to get a push to take off even if it did fit. But I will tell the owner of the...
Forum: Early V8 (1932-53) 11-22-2019, 01:00 PM
Replies: 14
Views: 1,116
Posted By Club Coupe
gear ratio

An acquaintance is trying to give me a differential for my 1950 Ford. It has 15 teeth on the pinion and 42 on the ring gear.
By my calculations that is a 2.80 ratio. Obviously I can't use it but I...
Showing results 1 to 11 of 11

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:33 AM.