Forum: Early V8 (1932-53)
07-04-2016, 06:48 PM
|
Replies: 7
Views: 1,097
Re: Paging the '35 truck experts - chassis issue
I had the same problem with mine poorly done patch. I cut it out made a new piece and welded it all up. Came out as good as new just make sure to weld the piece in parallel to a bar resting across...
|
Forum: Early V8 (1932-53)
04-17-2016, 01:03 AM
|
Replies: 74
Views: 13,475
|
Forum: Early V8 (1932-53)
01-20-2016, 01:24 AM
|
Replies: 7
Views: 2,146
Re: Air bubbles at head nuts
Thanks for everyone's responses I think Bored and stroked might have found the answer
"The only other thing that I can think of is that some of Edmunds heads were known for porosity - maybe there...
|
Forum: Early V8 (1932-53)
01-18-2016, 09:09 PM
|
Replies: 7
Views: 2,146
Air bubbles at head nuts
Hope to solve a mystery. I recently started up a new rebuild. 1941 block bored 20 over 3 3/16, mercury crank, stock cam, adjustable lifters, egge pistons. The block was decked .010 best 59A...
|
Forum: Early V8
05-12-2015, 05:08 PM
|
Replies: 4
Views: 1,487
|
Forum: Early V8
05-02-2015, 01:40 PM
|
Replies: 1
Views: 1,112
|
Forum: Early V8
04-27-2015, 04:05 PM
|
Replies: 1
Views: 1,112
head studs
Looking for 3 used head studs 3 1/8" thanks Mike
|
Forum: Early V8 (1932-53)
04-25-2015, 12:45 AM
|
Replies: 15
Views: 2,708
|
Forum: Early V8
04-23-2015, 11:57 AM
|
Replies: 4
Views: 1,487
|
Forum: Early V8
04-16-2015, 05:09 PM
|
Replies: 4
Views: 1,487
|
Forum: Early V8
04-10-2015, 03:04 PM
|
Replies: 4
Views: 1,487
|
Forum: Early V8
04-08-2015, 09:43 PM
|
Replies: 4
Views: 1,487
|
Forum: Early V8
04-02-2015, 03:40 PM
|
Replies: 0
Views: 1,090
8Ba pulley
Looking for double 5/8 groove front crank pulley for merc crank Thanks
|
Forum: Early V8
04-02-2015, 02:02 PM
|
Replies: 0
Views: 1,006
8Ba pulley
Looking for a double front pulley for 5/8 belt for merc crank. Thanks
|
Forum: Early V8 (1932-53)
09-11-2014, 08:00 PM
|
Replies: 4
Views: 1,012
|
Forum: Early V8 (1932-53)
09-11-2014, 04:59 PM
|
Replies: 4
Views: 1,012
1936 driveshaft bearing clearance
I have a 1936 pickup rebuilt the trans am ready to install it. The front driveshaft bearing has noticable movement up and down. Does anyone know the runout for this bearing? Thanks
|
Forum: Early V8
08-30-2014, 12:12 AM
|
Replies: 1
Views: 887
|
Forum: Early V8
08-27-2014, 06:42 PM
|
Replies: 1
Views: 887
|
Forum: Early V8
07-17-2014, 08:54 PM
|
Replies: 2
Views: 1,107
|
Forum: Early V8
07-12-2014, 01:18 AM
|
Replies: 2
Views: 1,107
|
Forum: Early V8
07-08-2014, 04:17 PM
|
Replies: 2
Views: 1,107
|
Forum: Early V8 (1932-53)
06-22-2014, 08:30 PM
|
Replies: 24
Views: 5,233
|
Forum: Early V8
06-06-2014, 11:55 PM
|
Replies: 1
Views: 827
|
Forum: Early V8
06-03-2014, 01:46 AM
|
Replies: 1
Views: 827
59 ab block
Looking for crack free 59 ab bare block for rebuild. Thanks
|
Forum: Early V8
05-12-2014, 12:20 PM
|
Replies: 1
Views: 1,201
|