Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.10 seconds.
Search: Posts Made By: Kurt in NJ
Forum: Model A (1928-31) Today, 02:01 AM
Replies: 9
Views: 323
Posted By Kurt in NJ
Re: Corn Head Grease Too Fluid for Gun

If the grease gun is made to use cartriges the piston is smaller to fit in the cartrige, try it with empty grease cartrige
Forum: Early V8 (1932-53) Yesterday, 06:27 PM
Replies: 5
Views: 164
Posted By Kurt in NJ
Re: Crank chunk

Crankshafts were cast in groups, that is where it was broke off the the cluster
Forum: Model A (1928-31) Yesterday, 01:30 PM
Replies: 19
Views: 662
Posted By Kurt in NJ
Re: Clutch stuck

My clutch got stuck. Wouldn't break loose, even got good at shifting without clutch, went on 40 mile drive, still wouldn't break loose, looking in I could see the hole in the disc, and that it was...
Forum: Model A (1928-31) Yesterday, 09:42 AM
Replies: 8
Views: 223
Posted By Kurt in NJ
Re: Front Main Spring

spring covers can be aftermarket or original ford --on page 316 of the service bulletins there are pictures and installation instructions
Forum: Model A (1928-31) 01-20-2020, 10:36 PM
Replies: 7
Views: 431
Posted By Kurt in NJ
Re: Ahooha

My horn gets set for parade or road, one click looser for parade, lower voltage, horn tune up-- drop of oil on each felt, clean commutator by rubbing with clean rag

Perhaps you should check the...
Forum: Early V8 (1932-53) 01-18-2020, 01:20 AM
Replies: 9
Views: 314
Posted By Kurt in NJ
Re: Allen Syncrograph Model E-316 Looking Info & Parts

I don't know model #, but probably similar internally, haven't found anything in parts, would like to find a meter lens, top one I sanded and polished, the bottom one has a big divot in the center,...
Forum: Model A (1928-31) 01-18-2020, 12:58 AM
Replies: 15
Views: 542
Posted By Kurt in NJ
Re: Head light focusing procedure

If you take the lens off, shine the light on a wall 25 feet away the property focused beam without the lens will look like this
Forum: Model A (1928-31) 01-15-2020, 04:35 PM
Replies: 21
Views: 737
Posted By Kurt in NJ
Re: steering sector

How was the sector fitted to the bushings -- how much clearance--- can you see it wiggling or moving side to side or in- out
Forum: Model A (1928-31) 01-15-2020, 12:31 PM
Replies: 17
Views: 700
Posted By Kurt in NJ
Re: Cracked Head

Glue it with jb weld and fill system to look for other problems, it froze in the past
Forum: Model A (1928-31) 01-15-2020, 01:42 AM
Replies: 8
Views: 298
Posted By Kurt in NJ
Re: Front generator bearing screeching.....

Have you ever lubricated the bearings as specified in the owners instruction book?
Forum: Early V8 (1932-53) 01-13-2020, 05:41 PM
Replies: 10
Views: 396
Posted By Kurt in NJ
Re: Simple DIY distributor/ignition bench tester

The article talks about building a tester for under a 100$, at Hershey I was looking for a vacuum gauge for a friend, stopped to look at Allen syncrograph, has a really nice vacuum gauge, was asked...
Forum: Early V8 (1932-53) 01-07-2020, 02:22 PM
Replies: 20
Views: 475
Posted By Kurt in NJ
Re: 47 pickup tranny

A60hp with 4:44 rear I had would do 74mph, either your brakes are dragging or the engine is low on power
Forum: Model A (1928-31) 01-07-2020, 01:36 PM
Replies: 13
Views: 561
Posted By Kurt in NJ
Re: Remove sector needle bearings

They should press straight through
Aftermarket 36 steering sectors usually had bushings to replace the needle bearings ---- they are the needle bearings used to replace bushings on the A
I also...
Forum: Model A (1928-31) 01-06-2020, 11:04 PM
Replies: 13
Views: 561
Posted By Kurt in NJ
Re: Remove sector needle bearings

If they are good now most likely they will be damaged in removing them, the seal should be able to be changed without disturbing the bearings--- what did the shaft on the old sector look like
Forum: Model A (1928-31) 01-02-2020, 10:55 PM
Replies: 44
Views: 2,027
Posted By Kurt in NJ
Re: Generator vs Alternator

Motoring it polarizes it
Make sure the field poles are not dragging on the armature--- that will burn it out,
What kind of bushing did you use, properly fitting one usually fits perfectly without...
Forum: Early V8 (1932-53) 01-02-2020, 05:54 PM
Replies: 27
Views: 1,576
Posted By Kurt in NJ
Re: Bellhousing indexing

I reality the bell housing doesn't matter, what matters is that the transmission centerline matches the crankshaft centerline
Forum: Early V8 (1932-53) 01-02-2020, 05:17 PM
Replies: 4
Views: 301
Posted By Kurt in NJ
Re: Air Filters

The K&Nfilters don't stop much, I always cringe when it is called a upgrade to rip out the innerds of a oil bath and put in a k&n

Another filter to look at is the capture size of a full flow...
Forum: Early V8 (1932-53) 01-01-2020, 03:51 AM
Replies: 18
Views: 695
Posted By Kurt in NJ
Re: Making your own gaskets

for something like that I would trace with sharp pencil, then cut with scalpel or new xacto knife, have leather punch pliers with assorted sizes along with gasket punches both homemade and factory
Forum: Early V8 (1932-53) 12-31-2019, 01:10 PM
Replies: 9
Views: 317
Posted By Kurt in NJ
Re: Radio repair

Tune it to the antenna--- usually near where the antenna wire goes in is a small adjustment screw in a hole--- antenna trimmer capacitor--- makes all the difference in reception-- I forget if best at...
Forum: Model A (1928-31) 12-31-2019, 01:05 PM
Replies: 14
Views: 693
Posted By Kurt in NJ
Re: Ways to Start With Obstructed Hand Crank

This would work, get a V8 crank
Forum: Model A (1928-31) 12-31-2019, 11:36 AM
Replies: 14
Views: 693
Posted By Kurt in NJ
Forum: Model A (1928-31) 12-31-2019, 07:48 AM
Replies: 8
Views: 472
Posted By Kurt in NJ
Re: Speedometer Cable Lube

I have used cv joint lube, it comes in small packages , and I have leftovers
Before you lube roll the cable on a table, if it rolls smooth it's straight, if a spot jumps work the bend out so the...
Forum: Early V8 (1932-53) 12-30-2019, 09:29 PM
Replies: 12
Views: 411
Posted By Kurt in NJ
Re: Fuel filter placement

pumps push trough a filter much better than they suck through a filter
Forum: Early V8 (1932-53) 12-30-2019, 01:59 PM
Replies: 11
Views: 445
Posted By Kurt in NJ
Re: Is there such a thing as columbia clutch ?

There's a friction clutch in the Columbia --- sorta like a synchronizer in a transmission to prevent clashing
Forum: Early V8 (1932-53) 12-30-2019, 01:41 PM
Replies: 16
Views: 770
Posted By Kurt in NJ
Re: Intake port repair

I was doing a valve job on a different flathead, there's evidence of "porting"attempts, in the #1 intake there's epoxy, didn't have coolant leaking problems ---- been glued for at least 15 years, I...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:45 AM.