Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Jacksonlll
Forum: Model A (1928-31) 09-19-2019, 08:00 PM
Replies: 8
Views: 379
Posted By Jacksonlll
Re: steering wheel on mush roomed threaded shaft

https://youtu.be/er3gKmcWZJs

See this video. It worked for me on a really stuck wheel. Use a lot of nylon rope and cover with a big towel in case something let’s go.
Forum: Model A (1928-31) 09-19-2019, 05:45 AM
Replies: 10
Views: 466
Posted By Jacksonlll
Re: 1930 Front brakes

The head of the pin in the center of the rollers should rest, and roll on a track that is rivetted to the back plate. Show us only the back plate.
Forum: Model A (1928-31) 09-18-2019, 04:13 PM
Replies: 23
Views: 659
Posted By Jacksonlll
Re: Model A dies over 45 mph

Sure sounds like your fuel line is going too far into the carb and it is hitting the side of the screen and the only flow you get is through the screen within the diameter of the tube. Just...
Forum: Model A (1928-31) 09-18-2019, 01:36 PM
Replies: 25
Views: 979
Posted By Jacksonlll
Re: Another new Model A owner.

That upper hose looks like it’s flexible. I’ve been looking for one to reduce the stress on the radiator inlet.
Forum: Model A (1928-31) 09-17-2019, 02:30 PM
Replies: 16
Views: 2,124
Posted By Jacksonlll
Re: Lebaron Bonney has closed????

An upholstery guy just told me that someone bought Lebaron bonney. I forgot the name. Something short like Red Hot or something like that.
Forum: Model A (1928-31) 09-16-2019, 07:53 PM
Replies: 15
Views: 491
Posted By Jacksonlll
Re: Resonant Rattle

Sure sounds like what the guys have already said. Get a rubber mallet and lightly hit the hood props, the radiator to dash rods, those engine pans and the windshield frame, and it should show itself.
Forum: Model A (1928-31) 09-16-2019, 04:26 PM
Replies: 27
Views: 778
Posted By Jacksonlll
Re: Ever have your engine die at a stop light?

Nex time you have the carb off, run a big file across the two mating mounting flanges. File until all is flat on both the carb and the intake flange. A tiny leak here can cause your prob and this is...
Forum: Model A (1928-31) 09-11-2019, 07:19 AM
Replies: 9
Views: 540
Posted By Jacksonlll
Re: Jumper wire

The wire from the switch to the dist is shorted to ground.
Forum: Model A (1928-31) 09-09-2019, 08:39 AM
Replies: 6
Views: 561
Posted By Jacksonlll
Re: RPMs measurement

Be careful of that fan blade and the belt. Not a friendly place to work.
Forum: Model A (1928-31) 09-09-2019, 08:36 AM
Replies: 7
Views: 375
Posted By Jacksonlll
Re: Timing/Spark control arm

Keep in mind that you can pull that rod up toward you to make room for whatever you do. It’s spring loaded at the bottom and will come up a bit.
Forum: Model A (1928-31) 09-06-2019, 07:05 PM
Replies: 8
Views: 501
Posted By Jacksonlll
Re: Flat spot in carburetor

Sounds like restricted fuel flow into the bowl. This happens on the Zenith when the feed tube is pushed in so far that it hits the filter screen in there.
Forum: Model A (1928-31) 09-06-2019, 07:02 PM
Replies: 31
Views: 1,242
Posted By Jacksonlll
Re: Stupid Question #2: how does an iron frame act as a ground on our cars

The structure is so big there is very little losses. No reason to use silver or copper. It’s just another big wire.
Forum: Model A (1928-31) 09-02-2019, 08:06 AM
Replies: 12
Views: 617
Posted By Jacksonlll
Re: New to the Addiction...

Unless you have a new radiator, your core is plugged. You want to run the belt as loose as you can. Just tight enough to work. Your overheating problem is not a loose belt.
Forum: Model A (1928-31) 08-31-2019, 08:24 AM
Replies: 14
Views: 610
Posted By Jacksonlll
Re: Oil Change Interval

500 if you don’t drive it much. A 1000 or more on long trips over a short time.
Forum: Model A (1928-31) 08-31-2019, 08:21 AM
Replies: 15
Views: 517
Posted By Jacksonlll
Re: The dreaded death wobble

Not by the book,but the way I stop it is by tightening the ends of the drag link and tie rod just where you can get the cotter pin in. Tighten pitman arm, check sector shaft bushings. Adjust gear,...
Forum: Model A (1928-31) 08-30-2019, 02:06 PM
Replies: 48
Views: 1,755
Posted By Jacksonlll
Re: Where to start?

If the points are open, both sides should be hot. Distributor side goes to the ignition switch on it’s way to the distributor.
Forum: Model A (1928-31) 08-28-2019, 05:57 PM
Replies: 9
Views: 453
Posted By Jacksonlll
Re: distrbuter screw

No, just the slotted stud and lock nut.
Forum: Model A (1928-31) 08-28-2019, 09:21 AM
Replies: 27
Views: 1,148
Posted By Jacksonlll
Re: hidden radio ideas or just slighty out of sight. wood hide door?

A radio is very hard to hear in an A. At road load you will have to turn the volume way up.
Forum: Model A (1928-31) 08-27-2019, 11:15 AM
Replies: 48
Views: 1,755
Posted By Jacksonlll
Re: Where to start?

Don’t even think about buying an interior until you get much further along. Get it running like a top, and then think about the cosmetics.
Forum: Model A (1928-31) 08-27-2019, 06:01 AM
Replies: 48
Views: 1,755
Posted By Jacksonlll
Re: Where to start?

Here is the playlist of my YouTube videos that should help you with a few things.
https://www.youtube.com/playlist?list=PLhL36Rc6o5MI5gsZreCrIa0r_fFQcz4R0

Join MARC, or MAFCA and a local club. ...
Forum: Model A (1928-31) 08-27-2019, 05:43 AM
Replies: 19
Views: 587
Posted By Jacksonlll
Re: what caused radiator failure?

Where did you find a softer hose? Even with slight movement of the engine, a stiff hose will transmit engine movement to the rad. inlet and put a lot of stress on that solder joint. I have seen...
Forum: Model A (1928-31) 08-24-2019, 07:46 PM
Replies: 49
Views: 1,886
Posted By Jacksonlll
Re: Transmission Issues

I bet Ryan is right.
Forum: Model A (1928-31) 08-23-2019, 12:23 PM
Replies: 9
Views: 481
Posted By Jacksonlll
Re: Distributor Body Rocking??

Tighten things up. The dist should be solid with no movement.
Forum: Model A (1928-31) 08-23-2019, 12:20 PM
Replies: 37
Views: 2,425
Posted By Jacksonlll
Re: My model A wont go faster than 40-45

Remove your fuel line from carb, and make sure the ferrule is no more than a 1/16 inch from end of tube. If too long, it will hit filter and block a lot of the fuel flow. Easy to check. Good luck.
Forum: Model A (1928-31) 08-22-2019, 06:13 PM
Replies: 18
Views: 863
Posted By Jacksonlll
Re: Motor Suddenly Stuck

Do not push it forward. That will just jam it more or break something. Push the car back and don’t bang on anything.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:25 AM.