Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts Made By: KenBolton
Forum: Model A (1928-31) 10-20-2020, 03:36 PM
Replies: 4
Views: 535
Posted By KenBolton
Re: A & L Metal Value Stems

The Medic has them.
Forum: Model A (1928-31) 10-20-2020, 01:18 PM
Replies: 4
Views: 535
Posted By KenBolton
A & L Metal Value Stems

I just became aware that there have been two manufacturers of Shrader valve stems. I ordered stems from Bratten’s a month ago and installed them in my tubes. At the time both the dust covers and stem...
Forum: Model A (1928-31) 10-17-2020, 08:04 PM
Replies: 1
Views: 203
Posted By KenBolton
Running Board Trim

My ‘30 Coupe has repro running boards with stainless steel trim. I’d like to change it over to zink. Bob Burdick doesn’t think his will work on repos. I see Sacramento Ford has zink trim for repro...
Forum: Model A (1928-31) 10-11-2020, 04:37 PM
Replies: 11
Views: 587
Posted By KenBolton
Headlight Focus Procedure

So far I’v found three different alignment heights from three different sources. 33”, 37” and 39 1/2”. Which is correct?
Forum: Model-A 09-07-2020, 03:28 PM
Replies: 0
Views: 114
Posted By KenBolton
Forum: Early V8 09-06-2020, 08:09 AM
Replies: 0
Views: 322
Posted By KenBolton
Forum: Model A (1928-31) 09-06-2020, 07:59 AM
Replies: 8
Views: 408
Posted By KenBolton
Re: Running Board Step Install

That’s what I was thinking, function over esthetics. It does look strange though. So far I haven’t been able to find any guidance in the “Standards”. Not a first there, they don’t cover everything.
Forum: Model A (1928-31) 09-05-2020, 08:17 PM
Replies: 8
Views: 408
Posted By KenBolton
Running Board Step Install

Wondering about the recommended spot on the running board for installation of step plates. On my coupe they are roughly centered with the doors. However, it seems like this is too far back for my...
Forum: Model-A 08-28-2020, 08:38 AM
Replies: 0
Views: 86
Posted By KenBolton
1929 Seat Springs FS

Tudor rear seat springs with wood base. Excellent condition.
Forum: Model A (1928-31) 08-27-2020, 03:53 PM
Replies: 13
Views: 962
Posted By KenBolton
Re: TDC Finder

Hard for one person to both crank and use the pin unless possibly if you’re under 30 and very athletic. Also to see the soapy bubble method. I plug the #1 hole with a rolled up paper towel. When you...
Forum: Model-A 08-27-2020, 03:43 PM
Replies: 0
Views: 155
Posted By KenBolton
Body Build Frame FS

Professionally straightened frame on approx 32” legs and casters. Don’t think I will need it again so offering to those who will. No shipping, pickup only. Legs are bolted to the frame so it could be...
Forum: Model A (1928-31) 08-19-2020, 08:15 AM
Replies: 9
Views: 564
Posted By KenBolton
Re: 1929 Business Coupe - Need more leg room

I am 6’2” and 230 lbs and was hesitant to remove the self tray on my 30 Coupe. I removed the clutch and brake peddles, then cut them down 3/4” and welded them back together. Did the same thing plus...
Forum: Model A (1928-31) 07-09-2020, 11:49 AM
Replies: 12
Views: 1,084
Posted By KenBolton
Re: Pickup Leg Room Needed

Yup, I bent the shifter to the right too. Thanks for all the input!
Forum: Model A (1928-31) 07-05-2020, 02:21 PM
Replies: 12
Views: 1,084
Posted By KenBolton
Pickup Leg Room Needed

I am six three, 220 lbs and 67 years young. I have shortened the brake and clutch peddles by 3/4” but still have a challenge getting into my 82-B with no seat installed. Touring Standards don’t like...
Showing results 1 to 14 of 14

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:43 AM.