Forum: Early V8
12-10-2019, 08:00 PM
|
Replies: 1
Views: 157
|
Forum: Early V8
12-03-2019, 11:07 PM
|
Replies: 1
Views: 157
2 speedway super 97 carbs
Two speedway super 97 carbs. Practically new when taken off but have been on the shelf for awhile. Comes with linkage. Any questions just ask.
|
Forum: Early V8 (1932-53)
12-02-2019, 09:18 PM
|
Replies: 7
Views: 250
Re: Light switch rod and steering box need help
I believe all the light switch rods are the same diameter as I have a 29 A light switch rod and it is the same diameter as my 35 light switch rod. Are the plates 78-3597 difficult to find? I don’t...
|
Forum: Model-A
12-02-2019, 08:47 PM
|
Replies: 0
Views: 119
Leaf spring singles needed
Doing some work on my car and have the front toor apart for service and noticed that my 2 large leafs directly above the main leaf are broke in half. Anybody have these two leafs?
|
Forum: Early V8 (1932-53)
12-02-2019, 08:34 PM
|
Replies: 7
Views: 250
Re: Light switch rod and steering box need help
I did some reading and it seems that end plates that had the steel tube are for 1940 and up because only the horn wire passed through. It seems that the plates that had a horn rod go through them had...
|
Forum: Early V8 (1932-53)
12-02-2019, 07:45 PM
|
Replies: 7
Views: 250
Light switch rod and steering box need help
Hi guys, I have a question regarding early boxes and headlight switch rods. I am putting together a ford using a 1948 ford F-1 steering box. I want to run my 1935 banjo wheel and light switch rod on...
|
Forum: Model-A
11-26-2019, 01:29 PM
|
Replies: 0
Views: 179
Late trans to 4 cylinder adapter
I have a specialty ford parts aluminum bellhousing to mount a 32-39 ford trans behind the stock 4 cylinder. Only have the bellhousing. Snyders has all the other parts you need for a bolt up kit. $250
|
Forum: Model-A
11-25-2019, 06:41 PM
|
Replies: 0
Views: 308
Ford model a engine
Ford model A engine. I was told it was a spare engine that an elderly man kept since 1957. It has .040 pistons, turns over just fine. Missing carb, head and a few other bits. $300
|
Forum: Early V8
11-21-2019, 01:11 PM
|
Replies: 0
Views: 110
37-39 steering box end plate needed
Looking for the end plate from a 37-39 ford steering box. It holds the headlight switch parts. The arrow indicates the part. Please let me know if you have one. Thanks.
|
Forum: Early V8
10-28-2019, 09:06 PM
|
Replies: 0
Views: 106
|
Forum: Model-A
10-22-2019, 10:00 PM
|
Replies: 0
Views: 187
Original patina 19” caps wanted
Looking for a set of 4 original patina 19” caps. Slight dings and scratches ok. Will buy singles if it’s all you have. Thanks.
|
Forum: Early V8
10-07-2019, 10:08 PM
|
Replies: 0
Views: 132
Crankshaft pulley 1936 wanted
Need a crankshaft pulley for my 1936 L-B. Don’t know if other years are the same. Please let me know if you have one. Thanks.
|
Forum: Early V8 (1932-53)
10-03-2019, 06:54 PM
|
Replies: 14
Views: 750
|
Forum: Early V8 (1932-53)
10-02-2019, 11:51 AM
|
Replies: 14
Views: 750
Cutting domes in 21 stud aluminum heads?
I have a pair of aluminum 21 stud factory heads but they are flat. My engine is a 36 LB and it has dome pistons. Is there enough material in the heads to cut the dome that is in my cast iron heads?...
|
Forum: Model A (1928-31)
09-23-2019, 10:42 AM
|
Replies: 8
Views: 734
Re: How many cc’s??
Thanks for the info guys. I have yet to pull the stock head to measure piston pop up if any.
|
Forum: Early V8
09-23-2019, 10:41 AM
|
Replies: 3
Views: 508
|
Forum: Model A (1928-31)
09-18-2019, 12:23 PM
|
Replies: 8
Views: 734
Re: How many cc’s??
I bought a head and it measures 125 cc. Just trying to figure out the compression ratio of it.
|
Forum: Model A (1928-31)
09-18-2019, 07:57 AM
|
Replies: 8
Views: 734
How many cc’s??
How many cc’s are stock heads? How many cc’s are Snyders 6:1 heads? I have a post saved from a few years ago where Bob Johnston says a 5:5 is 149 and a 6:1 is 137. According to Snyders catalog a 6:1...
|
Forum: Model A (1928-31)
08-22-2019, 04:51 PM
|
Replies: 8
Views: 759
|
Forum: Model A (1928-31)
08-21-2019, 06:50 PM
|
Replies: 8
Views: 759
Aristocrat dash swap
Hi guys,
I have an ad for an aristocrat dash panel and I did not put oval or round in the description. Have had a few people say they have one but it is for a round speedo, I have a 29 that is...
|
Forum: Model-A
08-16-2019, 09:09 PM
|
Replies: 0
Views: 178
|
Forum: Model-A
08-11-2019, 05:30 PM
|
Replies: 2
Views: 249
|
Forum: Model-A
08-09-2019, 11:52 PM
|
Replies: 2
Views: 249
|
Forum: Late V8
08-06-2019, 07:16 PM
|
Replies: 0
Views: 178
3.70 3rd member 28 spline
3.70 gear 3rd member. 28 spline. Nothing wrong just swapped out to a 3.00. Car axles can be included if needed. $125. Pickup only due to weight.
|
Forum: Early V8
08-06-2019, 07:14 PM
|
Replies: 0
Views: 138
3.70 gear 3rd member 28 spline
Have a 3.70 gear from my ‘60 F100. Swapped to a 3.00. Nothing wrong just decided I wanted to be able to do 70. Also have car axles that can go with. $125. Very heavy so no shipping.
|