Forum: Early V8 (1932-53)
04-15-2024, 06:13 PM
|
Replies: 11
Views: 995
|
Forum: Early V8 (1932-53)
01-28-2024, 09:52 AM
|
Replies: 12
Views: 782
|
Forum: Early V8 (1932-53)
01-08-2024, 07:28 PM
|
Replies: 23
Views: 1,141
|
Forum: Early V8 (1932-53)
12-23-2023, 06:16 PM
|
Replies: 17
Views: 1,130
Re: Edelbrock 1116 heads
Those ARP studs are listed as 3.16 long. You may be able to use the Speedway stud kit for the earlier 39-48 heads which are 3.25 long and only $115. They are all the same length....
|
Forum: Early V8 (1932-53)
12-21-2023, 07:40 PM
|
Replies: 35
Views: 2,626
|
Forum: Early V8 (1932-53)
12-16-2023, 03:35 PM
|
Replies: 9
Views: 756
|
Forum: Early V8 (1932-53)
11-30-2023, 07:00 PM
|
Replies: 79
Views: 5,129
|
Forum: Early V8 (1932-53)
11-27-2023, 09:25 AM
|
Replies: 16
Views: 1,150
Re: Door panel backing material?
I've used sheets of wood paneling around 1/8" thick. Some use masonite but it's thicker. There are sheets of expanded pvc that sign makers use. Also the real door panel material is available but...
|
Forum: Early V8 (1932-53)
11-26-2023, 04:45 PM
|
Replies: 4
Views: 556
Re: Gas Spillage
Can anything go bad other than the seal? Try switching the seal from your other cap or make one. Just a thought. Having gas coming out going around corners seems a little unusual to begin with. Maybe...
|
Forum: Early V8 (1932-53)
11-12-2023, 03:51 PM
|
Replies: 7
Views: 854
Re: Wheel bearings?
Kanter is another source. https://www.kanter.com/p-35864-search.html?fitment=1950%7CMercury&orientation=vertical&page=2
|
Forum: Early V8 (1932-53)
11-05-2023, 09:04 AM
|
Replies: 12
Views: 781
Re: Hub Stuck
My hub puller is different, but the directions say to hit the center shaft with a hammer to pop the taper, if needed. Worth a try?
|
Forum: Early V8 (1932-53)
11-02-2023, 06:24 AM
|
Replies: 33
Views: 2,455
|
Forum: Early V8 (1932-53)
11-01-2023, 09:32 PM
|
Replies: 33
Views: 2,455
|
Forum: Early V8 (1932-53)
10-22-2023, 08:45 PM
|
Replies: 19
Views: 1,816
Re: Carson Top
You hardly hear about a Carson tops anymore. Custom made tops. The old little mags would have builds in them. I recall they had like a tubular frame covered with chicken wire and upholstery. I have a...
|
Forum: Early V8 (1932-53)
10-05-2023, 12:23 PM
|
Replies: 12
Views: 858
|
Forum: Early V8 (1932-53)
09-26-2023, 06:27 PM
|
Replies: 20
Views: 1,628
Re: Garage lift
MaxJack used to be real popular over at the Garage Journal. Portable 2 post lift. ...
|
Forum: Early V8 (1932-53)
09-10-2023, 09:16 PM
|
Replies: 11
Views: 1,017
|
Forum: Early V8 (1932-53)
08-26-2023, 10:43 AM
|
Replies: 18
Views: 1,258
Re: Best wheel bearings:
I'm sure you can get quality parts from dealers on this site. Van Pelts and Third Gen are a couple.
|
Forum: Early V8 (1932-53)
07-19-2023, 12:08 PM
|
Replies: 13
Views: 872
|
Forum: Early V8 (1932-53)
07-14-2023, 06:44 PM
|
Replies: 2
Views: 474
|
Forum: Early V8 (1932-53)
07-07-2023, 06:14 AM
|
Replies: 15
Views: 928
|
Forum: Early V8 (1932-53)
06-23-2023, 08:45 AM
|
Replies: 49
Views: 8,191
Re: George Mitchell
Here is a picture of my Systematics MIG welder that my father bought over 40 yrs ago. Very good mig welder.
|
Forum: Early V8 (1932-53)
06-15-2023, 02:43 PM
|
Replies: 3
Views: 510
Re: intake manifold
Starting in the center and working your way out in a crisscross fashion, tighten all of the intake manifold bolts to 20-25 ft/lbs. Per Edelbrock.
|
Forum: Early V8 (1932-53)
06-02-2023, 06:11 AM
|
Replies: 5
Views: 680
|
Forum: Early V8 (1932-53)
05-03-2023, 10:39 AM
|
Replies: 5
Views: 768
|