Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: Bob C
Forum: Model A (1928-31) 02-19-2021, 03:51 PM
Replies: 4
Views: 315
Posted By Bob C
Re: Canadian Patent Plate

Like this. https://www.mikes-afordable.com/product/A18650C.html
Forum: Model A (1928-31) 02-18-2021, 09:32 PM
Replies: 9
Views: 328
Posted By Bob C
Re: AA truck radiator question

This is a AA radiator shell that takes the thicker radiator, notice no widows peak.
Forum: Model A (1928-31) 02-18-2021, 06:53 PM
Replies: 9
Views: 328
Posted By Bob C
Re: AA truck radiator question

Yes and no. In April 1930 they went to a wider 4 row of tube radiator.
Forum: Model A (1928-31) 02-18-2021, 06:46 PM
Replies: 1
Views: 131
Posted By Bob C
Re: AA truck front end question

The Feb 1936 Service Bulletins show the A and AA camber and toe the same, the
AA has a little less caster.
Forum: Model A (1928-31) 02-16-2021, 01:35 PM
Replies: 11
Views: 427
Posted By Bob C
Re: 1931 Wide Bed Pickup Cowl band

Yes, page E-88 of the Judging Standards.
Forum: Model A (1928-31) 02-16-2021, 12:24 PM
Replies: 24
Views: 3,283
Posted By Bob C
Re: Engine Bearings

This started in post 16 when the thread was high jacked instead of starting a new thread.
Forum: Model A (1928-31) 02-16-2021, 12:07 PM
Replies: 11
Views: 427
Posted By Bob C
Re: 1931 Wide Bed Pickup Cowl band

Body color is correct.
Forum: Early V8 (1932-53) 02-16-2021, 11:31 AM
Replies: 9
Views: 321
Posted By Bob C
Re: 1936 Intake manifold

Cab Over Engine
Forum: Early V8 (1932-53) 02-16-2021, 11:30 AM
Replies: 17
Views: 827
Posted By Bob C
Re: Flathead identification

As Alan mentioned, not a truck oil pan.
Forum: Model A (1928-31) 02-15-2021, 05:49 PM
Replies: 20
Views: 847
Posted By Bob C
Re: Rear axle housing grease zerk question

This is from page 361 of the Service Bulletins.


Rear axle shaft, drive shaft, and rear wheel
grease retainers, part numbers A-4245 and
A-1175, must be installed with the sharp edge
of the...
Forum: Early V8 (1932-53) 02-14-2021, 07:41 PM
Replies: 6
Views: 220
Posted By Bob C
Re: 47 pickup 100vs60 mph speedometer

Do the odometers read accurately?
Forum: Early V8 (1932-53) 02-14-2021, 07:16 PM
Replies: 2
Views: 118
Posted By Bob C
Re: F-1 Brake/Clutch pedal support question

In the parts book is shows a pin at the grease fitting end of the shaft.
The shaft looks like part # O1T-7606 and the bushings B-7526-A
Forum: Early V8 (1932-53) 02-14-2021, 11:28 AM
Replies: 5
Views: 278
Posted By Bob C
Re: wiper motor ID?

A little late to the party but I have Trico catalogs that cover 1927-1946
and I didn't see KSB 600 listed.
Looks like OldGold is right, a universal motor.
Forum: Model A (1928-31) 02-13-2021, 02:12 PM
Replies: 17
Views: 846
Posted By Bob C
Re: B Carb Questions

This is out of print and no longer available. To bad it was a great book.
Forum: Model A (1928-31) 02-12-2021, 05:23 PM
Replies: 7
Views: 423
Posted By Bob C
Re: NewRex Ignition Switch with Auxiliary Position

The ignition shouldn't be on when it's turned to ACC.
Forum: Early V8 (1932-53) 02-11-2021, 12:01 PM
Replies: 2
Views: 408
Posted By Bob C
Re: K R wILSON TOOL

How about a picture??
Forum: Model A (1928-31) 02-10-2021, 05:35 PM
Replies: 6
Views: 381
Posted By Bob C
Re: Front Brake operating pin

Model A drums are 11", 1932 are 12"
Forum: Model A (1928-31) 02-10-2021, 04:46 PM
Replies: 6
Views: 381
Posted By Bob C
Re: Front Brake operating pin

The 1932 had 12" brakes so needs a longer operating pin.
Forum: Model A (1928-31) 02-09-2021, 05:43 PM
Replies: 17
Views: 729
Posted By Bob C
Re: How to clean our inside cast sediment bowl?

I use Rust 911, comes out looking like new. If it's really bad it
may take a couple of soakings. I bought a pyrex bowl and a desktop
coffee cup warmer for use in the winter as the solution...
Forum: Model A (1928-31) 02-09-2021, 11:22 AM
Replies: 29
Views: 1,170
Posted By Bob C
Re: Fatigue Cracks In Model "A" Parts

Here's a common one. No picture but the steering column by the spark and
throttle rods.
Forum: Model A (1928-31) 02-08-2021, 07:36 PM
Replies: 2
Views: 288
Posted By Bob C
Re: Cowell lacing with wire - 1929 Model A

Here's an old thread that may help. https://www.fordbarn.com/forum/showthread.php?t=53780
Forum: Early V8 (1932-53) 02-08-2021, 05:34 PM
Replies: 3
Views: 331
Posted By Bob C
Re: Horn Wiring

The hook up looks similar to a Model A horn.
Forum: Model A (1928-31) 02-08-2021, 02:47 PM
Replies: 18
Views: 514
Posted By Bob C
Re: windshield frame size

1928-29 stock stanchions did not fold, 1930-31 did.
Forum: Model A (1928-31) 02-08-2021, 12:11 PM
Replies: 12
Views: 480
Posted By Bob C
Re: Horn wiring question

As mentioned the cover screw can be to long and contact the brush holder.
Forum: Model A (1928-31) 02-07-2021, 07:07 PM
Replies: 18
Views: 514
Posted By Bob C
Re: windshield frame size

Found another picture.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:59 AM.